Re: [PATCH v11 1/4] dmaengine: 8250_mtk_dma: add MediaTek uart DMA support
From: Sean Wang
Date: Sun Mar 10 2019 - 20:32:13 EST
Hi, Long
List some comments as the below and this week I will find a board to
test and then improve the driver.
Sean
On Wed, Mar 6, 2019 at 5:45 PM Long Cheng <long.cheng@xxxxxxxxxxxx> wrote:
>
> In DMA engine framework, add 8250 uart dma to support MediaTek uart.
> If MediaTek uart enabled(SERIAL_8250_MT6577), and want to improve
> the performance, can enable the function.
>
> Signed-off-by: Long Cheng <long.cheng@xxxxxxxxxxxx>
> ---
> drivers/dma/mediatek/Kconfig | 11 +
> drivers/dma/mediatek/Makefile | 1 +
> drivers/dma/mediatek/mtk-uart-apdma.c | 660 +++++++++++++++++++++++++++++++++
> 3 files changed, 672 insertions(+)
> create mode 100644 drivers/dma/mediatek/mtk-uart-apdma.c
>
> diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> index 680fc05..ac49eb6 100644
> --- a/drivers/dma/mediatek/Kconfig
> +++ b/drivers/dma/mediatek/Kconfig
> @@ -24,3 +24,14 @@ config MTK_CQDMA
>
> This controller provides the channels which is dedicated to
> memory-to-memory transfer to offload from CPU.
> +
> +config MTK_UART_APDMA
> + tristate "MediaTek SoCs APDMA support for UART"
> + depends on OF && SERIAL_8250_MT6577
> + select DMA_ENGINE
> + select DMA_VIRTUAL_CHANNELS
> + help
> + Support for the UART DMA engine found on MediaTek MTK SoCs.
> + When SERIAL_8250_MT6577 is enabled, and if you want to use DMA,
> + you can enable the config. The DMA engine can only be used
> + with MediaTek SoCs.
> diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> index 41bb381..61a6d29 100644
> --- a/drivers/dma/mediatek/Makefile
> +++ b/drivers/dma/mediatek/Makefile
> @@ -1,2 +1,3 @@
> +obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
> obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> obj-$(CONFIG_MTK_CQDMA) += mtk-cqdma.o
> diff --git a/drivers/dma/mediatek/mtk-uart-apdma.c b/drivers/dma/mediatek/mtk-uart-apdma.c
> new file mode 100644
> index 0000000..9ed7a49
> --- /dev/null
> +++ b/drivers/dma/mediatek/mtk-uart-apdma.c
> @@ -0,0 +1,660 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * MediaTek Uart APDMA driver.
> + *
> + * Copyright (c) 2018 MediaTek Inc.
> + * Author: Long Cheng <long.cheng@xxxxxxxxxxxx>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/dmaengine.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/list.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_dma.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +#include "../virt-dma.h"
> +
> +/* The default number of virtual channel */
> +#define MTK_UART_APDMA_NR_VCHANS 8
> +
> +#define VFF_EN_B BIT(0)
> +#define VFF_STOP_B BIT(0)
> +#define VFF_FLUSH_B BIT(0)
> +#define VFF_4G_SUPPORT_B BIT(0)
> +#define VFF_RX_INT_EN0_B BIT(0) /* rx valid size >= vff thre */
> +#define VFF_RX_INT_EN1_B BIT(1)
> +#define VFF_TX_INT_EN_B BIT(0) /* tx left size >= vff thre */
> +#define VFF_WARM_RST_B BIT(0)
> +#define VFF_RX_INT_CLR_B (BIT(0) | BIT(1))
> +#define VFF_TX_INT_CLR_B 0
> +#define VFF_STOP_CLR_B 0
> +#define VFF_INT_EN_CLR_B 0
> +#define VFF_4G_SUPPORT_CLR_B 0
> +
> +/* interrupt trigger level for tx */
> +#define VFF_TX_THRE(n) ((n) * 7 / 8)
> +/* interrupt trigger level for rx */
> +#define VFF_RX_THRE(n) ((n) * 3 / 4)
> +
> +#define VFF_RING_SIZE 0xffffU
> +/* invert this bit when wrap ring head again */
> +#define VFF_RING_WRAP 0x10000U
> +
> +#define VFF_INT_FLAG 0x00
> +#define VFF_INT_EN 0x04
> +#define VFF_EN 0x08
> +#define VFF_RST 0x0c
> +#define VFF_STOP 0x10
> +#define VFF_FLUSH 0x14
> +#define VFF_ADDR 0x1c
> +#define VFF_LEN 0x24
> +#define VFF_THRE 0x28
> +#define VFF_WPT 0x2c
> +#define VFF_RPT 0x30
> +/* TX: the buffer size HW can read. RX: the buffer size SW can read. */
> +#define VFF_VALID_SIZE 0x3c
> +/* TX: the buffer size SW can write. RX: the buffer size HW can write. */
> +#define VFF_LEFT_SIZE 0x40
> +#define VFF_DEBUG_STATUS 0x50
> +#define VFF_4G_SUPPORT 0x54
> +
> +struct mtk_uart_apdmadev {
> + struct dma_device ddev;
> + struct clk *clk;
> + bool support_33bits;
> + unsigned int dma_requests;
> + unsigned int *dma_irq;
> +};
> +
> +struct mtk_uart_apdma_desc {
> + struct virt_dma_desc vd;
> +
> + unsigned int avail_len;
> +};
> +
> +struct mtk_chan {
> + struct virt_dma_chan vc;
> + struct dma_slave_config cfg;
> + void __iomem *base;
> + struct mtk_uart_apdma_desc *desc;
> +
> + enum dma_transfer_direction dir;
> +
> + bool requested;
> +
> + unsigned int rx_status;
> +};
> +
> +static inline struct mtk_uart_apdmadev *
> +to_mtk_uart_apdma_dev(struct dma_device *d)
> +{
> + return container_of(d, struct mtk_uart_apdmadev, ddev);
> +}
> +
> +static inline struct mtk_chan *to_mtk_uart_apdma_chan(struct dma_chan *c)
> +{
> + return container_of(c, struct mtk_chan, vc.chan);
> +}
> +
> +static inline struct mtk_uart_apdma_desc *to_mtk_uart_apdma_desc
> + (struct dma_async_tx_descriptor *t)
> +{
> + return container_of(t, struct mtk_uart_apdma_desc, vd.tx);
> +}
> +
> +static void mtk_uart_apdma_write(struct mtk_chan *c,
> + unsigned int reg, unsigned int val)
> +{
> + writel(val, c->base + reg);
> +}
> +
> +static unsigned int mtk_uart_apdma_read(struct mtk_chan *c, unsigned int reg)
> +{
> + return readl(c->base + reg);
> +}
> +
> +static void mtk_uart_apdma_desc_free(struct virt_dma_desc *vd)
> +{
> + struct dma_chan *chan = vd->tx.chan;
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> +
> + kfree(c->desc);
> +}
> +
> +static void mtk_uart_apdma_start_tx(struct mtk_chan *c)
> +{
> + unsigned int len, send, left, wpt, d_wpt, tmp;
> + int ret;
> +
> + left = mtk_uart_apdma_read(c, VFF_LEFT_SIZE);
> + if (!left) {
> + mtk_uart_apdma_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
> + return;
> + }
> +
> + /* Wait 1sec for flush, can't sleep */
> + ret = readx_poll_timeout(readl, c->base + VFF_FLUSH, tmp,
> + tmp != VFF_FLUSH_B, 0, 1000000);
It is really not a good idea that polling up to 1 second in an
interrupt context.
> + if (ret)
> + dev_warn(c->vc.chan.device->dev, "tx: fail, debug=0x%x\n",
> + mtk_uart_apdma_read(c, VFF_DEBUG_STATUS));
> +
> + send = min_t(unsigned int, left, c->desc->avail_len);
> + wpt = mtk_uart_apdma_read(c, VFF_WPT);
> + len = c->cfg.dst_port_window_size;
> +
> + d_wpt = wpt + send;
> + if ((d_wpt & VFF_RING_SIZE) >= len) {
I am confused what size of VFF is. Either VFF_RING_SIZE or
c->cfg.dst_port_window_size?
> + d_wpt = d_wpt - len;
> + d_wpt = d_wpt ^ VFF_RING_WRAP;
> + }
> + mtk_uart_apdma_write(c, VFF_WPT, d_wpt);
> +
> + c->desc->avail_len -= send;
> +
> + mtk_uart_apdma_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
Why should we need to program interrupt enabled bit again?
> + if (mtk_uart_apdma_read(c, VFF_FLUSH) == 0U)
> + mtk_uart_apdma_write(c, VFF_FLUSH, VFF_FLUSH_B);
> +}
> +
> +static void mtk_uart_apdma_start_rx(struct mtk_chan *c)
> +{
> + struct mtk_uart_apdma_desc *d = c->desc;
> + unsigned int len, wg, rg;
> + int cnt;
> +
> + if ((mtk_uart_apdma_read(c, VFF_VALID_SIZE) == 0U) ||
> + !d || !vchan_next_desc(&c->vc))
> + return;
If the current descriptor is not available, the hardware should be
idle or stopped. so I think the condition can be removed or there is
somewhere your handle descriptors incorrectly.
> +
> + len = c->cfg.src_port_window_size;
> + rg = mtk_uart_apdma_read(c, VFF_RPT);
> + wg = mtk_uart_apdma_read(c, VFF_WPT);
> + cnt = (wg & VFF_RING_SIZE) - (rg & VFF_RING_SIZE);
Is it possible that rg and wg would be greater than VFF_RING_SIZE?
> + /*
> + * The buffer is ring buffer. If wrap bit different,
> + * represents the start of the next cycle for WPT
> + */
> + if ((rg ^ wg) & VFF_RING_WRAP)
> + cnt += len;
Again, I am confused what size of VFF is. Either VFF_RING_SIZE or
c->cfg.dst_port_window_size?
> +
> + c->rx_status = d->avail_len - cnt;
> + mtk_uart_apdma_write(c, VFF_RPT, wg);
> +
> + list_del(&d->vd.node);
> + vchan_cookie_complete(&d->vd);
> +}
> +
> +static irqreturn_t mtk_uart_apdma_irq_handler(int irq, void *dev_id)
> +{
> + struct dma_chan *chan = (struct dma_chan *)dev_id;
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + struct mtk_uart_apdma_desc *d;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&c->vc.lock, flags);
> + if (c->dir == DMA_DEV_TO_MEM) {
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_RX_INT_CLR_B);
> + mtk_uart_apdma_start_rx(c);
> + } else if (c->dir == DMA_MEM_TO_DEV) {
> + d = c->desc;
> +
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_TX_INT_CLR_B);
> +
> + if (d->avail_len != 0U) {
> + mtk_uart_apdma_start_tx(c);
> + } else {
> + list_del(&d->vd.node);
> + vchan_cookie_complete(&d->vd);
> + }
> + }
> + spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int mtk_uart_apdma_alloc_chan_resources(struct dma_chan *chan)
> +{
> + struct mtk_uart_apdmadev *mtkd = to_mtk_uart_apdma_dev(chan->device);
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + unsigned int tmp;
> + int ret;
> +
> + pm_runtime_get_sync(mtkd->ddev.dev);
Add an error handling, something like
err = pm_runtime_get_sync(mtkd->ddev.dev);
if (err < 0) {
pm_runtime_put_noidle(dev);
...
}
> +
> + mtk_uart_apdma_write(c, VFF_ADDR, 0);
> + mtk_uart_apdma_write(c, VFF_THRE, 0);
> + mtk_uart_apdma_write(c, VFF_LEN, 0);
> + mtk_uart_apdma_write(c, VFF_RST, VFF_WARM_RST_B);
> +
> + ret = readx_poll_timeout(readl, c->base + VFF_EN, tmp, !tmp, 10, 100);
> + if (ret) {
> + dev_err(chan->device->dev, "dma reset: fail, timeout\n");
> + return ret;
> + }
> +
> + if (!c->requested) {
> + c->requested = true;
The variable c->requested can be saved since the same channel
shouldn't be requested more one time
> + ret = request_irq(mtkd->dma_irq[chan->chan_id],
> + mtk_uart_apdma_irq_handler, IRQF_TRIGGER_NONE,
> + KBUILD_MODNAME, chan);
> + if (ret < 0) {
> + dev_err(chan->device->dev, "Can't request dma IRQ\n");
> + return -EINVAL;
> + }
> + }
> +
> + if (mtkd->support_33bits)
> + mtk_uart_apdma_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_CLR_B);
> +
> + return ret;
> +}
> +
> +static void mtk_uart_apdma_free_chan_resources(struct dma_chan *chan)
> +{
> + struct mtk_uart_apdmadev *mtkd = to_mtk_uart_apdma_dev(chan->device);
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> +
> + if (c->requested) {
ditto as the above
> + c->requested = false;
> + free_irq(mtkd->dma_irq[chan->chan_id], chan);
> + }
> +
> + tasklet_kill(&c->vc.task);
> +
> + vchan_free_chan_resources(&c->vc);
> +
> + pm_runtime_put_sync(mtkd->ddev.dev);
> +}
> +
> +static enum dma_status mtk_uart_apdma_tx_status(struct dma_chan *chan,
> + dma_cookie_t cookie,
> + struct dma_tx_state *txstate)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + enum dma_status ret;
> +
> + ret = dma_cookie_status(chan, cookie, txstate);
> +
> + dma_set_residue(txstate, c->rx_status);
> +
The handling is not enough. You should get the descriptor
corresponding to the cookie and then calculate and return the
->tx_status by the descriptor
> + return ret;
> +}
> +
> +static void mtk_uart_apdma_config_write(struct dma_chan *chan,
> + struct dma_slave_config *cfg,
> + enum dma_transfer_direction dir)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + struct mtk_uart_apdmadev *mtkd =
> + to_mtk_uart_apdma_dev(c->vc.chan.device);
> + unsigned int tmp;
> +
> + if (mtk_uart_apdma_read(c, VFF_EN) == VFF_EN_B)
> + return;
> +
> + c->dir = dir;
The direction is fixed by the device, I don't think it is required to
keep it in a software state.
> +
> + if (dir == DMA_DEV_TO_MEM) {
> + tmp = cfg->src_port_window_size;
> +
> + mtk_uart_apdma_write(c, VFF_ADDR, cfg->src_addr);
That is wrong. ->src_addr is the physical address where DMA slave data
should be read (RX), not the memory address.
You should program the register VFF_ADDR and VFF_LEN by sg address and
length from device_prep_slave_sg.
> + mtk_uart_apdma_write(c, VFF_LEN, tmp);
> + mtk_uart_apdma_write(c, VFF_THRE, VFF_RX_THRE(tmp));
> + mtk_uart_apdma_write(c, VFF_INT_EN,
> + VFF_RX_INT_EN0_B | VFF_RX_INT_EN1_B);
> + mtk_uart_apdma_write(c, VFF_RPT, 0);
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_RX_INT_CLR_B);
> + } else if (dir == DMA_MEM_TO_DEV) {
> + tmp = cfg->dst_port_window_size;
> +
> + mtk_uart_apdma_write(c, VFF_ADDR, cfg->dst_addr);
That is also wrong. st_addr: this is the physical address where DMA
slave data should be written (TX), not the memory address similar to
the above explanation.
> + mtk_uart_apdma_write(c, VFF_LEN, tmp);
> + mtk_uart_apdma_write(c, VFF_THRE, VFF_TX_THRE(tmp));
> + mtk_uart_apdma_write(c, VFF_WPT, 0);
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_TX_INT_CLR_B);
> + }
> +
> + mtk_uart_apdma_write(c, VFF_EN, VFF_EN_B);
> +
> + if (mtkd->support_33bits)
> + mtk_uart_apdma_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> +
> + if (mtk_uart_apdma_read(c, VFF_EN) != VFF_EN_B)
> + dev_err(chan->device->dev, "dir[%d] fail\n", dir);
> +}
> +
> +/*
> + * dmaengine_prep_slave_single will call the function. and sglen is 1.
> + * 8250 uart using one ring buffer, and deal with one sg.
> + */
> +static struct dma_async_tx_descriptor *mtk_uart_apdma_prep_slave_sg
> + (struct dma_chan *chan, struct scatterlist *sgl,
> + unsigned int sglen, enum dma_transfer_direction dir,
> + unsigned long tx_flags, void *context)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + struct mtk_uart_apdma_desc *d;
> +
> + if (!is_slave_direction(dir))
> + return NULL;
> +
> + mtk_uart_apdma_config_write(chan, &c->cfg, dir);
> +
> + /* Now allocate and setup the descriptor */
> + d = kzalloc(sizeof(*d), GFP_ATOMIC);
> + if (!d)
> + return NULL;
> +
> + /* sglen is 1 */
> + d->avail_len = sg_dma_len(sgl);
> + c->rx_status = d->avail_len;
> +
> + return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
> +}
> +
> +static void mtk_uart_apdma_issue_pending(struct dma_chan *chan)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + struct virt_dma_desc *vd;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&c->vc.lock, flags);
> + if (vchan_issue_pending(&c->vc)) {
> + vd = vchan_next_desc(&c->vc);
> + c->desc = to_mtk_uart_apdma_desc(&vd->tx);
> + }
> +
> + if (c->dir == DMA_DEV_TO_MEM)
> + mtk_uart_apdma_start_rx(c);
> + else if (c->dir == DMA_MEM_TO_DEV)
> + mtk_uart_apdma_start_tx(c);
> +
> + spin_unlock_irqrestore(&c->vc.lock, flags);
> +}
> +
> +static int mtk_uart_apdma_slave_config(struct dma_chan *chan,
> + struct dma_slave_config *config)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> +
> + memcpy(&c->cfg, config, sizeof(*config));
> +
> + return 0;
> +}
> +
> +static int mtk_uart_apdma_terminate_all(struct dma_chan *chan)
> +{
> + struct mtk_chan *c = to_mtk_uart_apdma_chan(chan);
> + unsigned long flags;
> + unsigned int tmp;
> + int ret;
> +
> + spin_lock_irqsave(&c->vc.lock, flags);
> +
> + mtk_uart_apdma_write(c, VFF_FLUSH, VFF_FLUSH_B);
> + /* Wait 1sec for flush, can't sleep */
> + ret = readx_poll_timeout(readl, c->base + VFF_FLUSH, tmp,
> + tmp != VFF_FLUSH_B, 0, 1000000);
It is extremely bad pending so long is in the spin_lock_irqsave
> + if (ret)
> + dev_err(c->vc.chan.device->dev, "flush: fail, debug=0x%x\n",
> + mtk_uart_apdma_read(c, VFF_DEBUG_STATUS));
> +
> + /* set stop as 1 -> wait until en is 0 -> set stop as 0 */
> + mtk_uart_apdma_write(c, VFF_STOP, VFF_STOP_B);
> + ret = readx_poll_timeout(readl, c->base + VFF_EN, tmp, !tmp, 10, 100);
> + if (ret)
> + dev_err(c->vc.chan.device->dev, "stop: fail, debug=0x%x\n",
> + mtk_uart_apdma_read(c, VFF_DEBUG_STATUS));
> +
> + mtk_uart_apdma_write(c, VFF_STOP, VFF_STOP_CLR_B);
> + mtk_uart_apdma_write(c, VFF_INT_EN, VFF_INT_EN_CLR_B);
> +
> + if (c->dir == DMA_DEV_TO_MEM)
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_RX_INT_CLR_B);
> + else if (c->dir == DMA_MEM_TO_DEV)
> + mtk_uart_apdma_write(c, VFF_INT_FLAG, VFF_TX_INT_CLR_B);
> +
> + spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> + return 0;
> +}
> +
> +static int mtk_uart_apdma_device_pause(struct dma_chan *chan)
> +{
> + /* just for check caps pass */
> + dev_err(chan->device->dev, "Pause can't support\n");
> +
If the device can't support hardware pause, we can do it as a software
pause in an implementation based on vdesc.
> + return 0;
> +}
> +
> +static void mtk_uart_apdma_free(struct mtk_uart_apdmadev *mtkd)
> +{
> + while (!list_empty(&mtkd->ddev.channels)) {
> + struct mtk_chan *c = list_first_entry(&mtkd->ddev.channels,
> + struct mtk_chan, vc.chan.device_node);
> +
> + list_del(&c->vc.chan.device_node);
> + tasklet_kill(&c->vc.task);
> + }
> +}
> +
> +static const struct of_device_id mtk_uart_apdma_match[] = {
> + { .compatible = "mediatek,mt6577-uart-dma", },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, mtk_uart_apdma_match);
> +
> +static int mtk_uart_apdma_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + struct mtk_uart_apdmadev *mtkd;
> + struct resource *res;
> + struct mtk_chan *c;
> + int bit_mask = 32, rc;
> + unsigned int i;
> +
> + mtkd = devm_kzalloc(&pdev->dev, sizeof(*mtkd), GFP_KERNEL);
> + if (!mtkd)
> + return -ENOMEM;
> +
> + mtkd->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(mtkd->clk)) {
> + dev_err(&pdev->dev, "No clock specified\n");
> + rc = PTR_ERR(mtkd->clk);
> + return rc;
> + }
> +
> + if (of_property_read_bool(np, "mediatek,dma-33bits"))
> + mtkd->support_33bits = true;
> +
> + if (mtkd->support_33bits)
> + bit_mask = 33;
> +
> + rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(bit_mask));
> + if (rc)
> + return rc;
> +
> + dma_cap_set(DMA_SLAVE, mtkd->ddev.cap_mask);
> + mtkd->ddev.device_alloc_chan_resources =
> + mtk_uart_apdma_alloc_chan_resources;
> + mtkd->ddev.device_free_chan_resources =
> + mtk_uart_apdma_free_chan_resources;
> + mtkd->ddev.device_tx_status = mtk_uart_apdma_tx_status;
> + mtkd->ddev.device_issue_pending = mtk_uart_apdma_issue_pending;
> + mtkd->ddev.device_prep_slave_sg = mtk_uart_apdma_prep_slave_sg;
> + mtkd->ddev.device_config = mtk_uart_apdma_slave_config;
> + mtkd->ddev.device_pause = mtk_uart_apdma_device_pause;
> + mtkd->ddev.device_terminate_all = mtk_uart_apdma_terminate_all;
> + mtkd->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> + mtkd->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> + mtkd->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
> + mtkd->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
> + mtkd->ddev.dev = &pdev->dev;
> + INIT_LIST_HEAD(&mtkd->ddev.channels);
> +
> + mtkd->dma_requests = MTK_UART_APDMA_NR_VCHANS;
> + if (of_property_read_u32(np, "dma-requests", &mtkd->dma_requests)) {
> + dev_info(&pdev->dev,
> + "Using %u as missing dma-requests property\n",
> + MTK_UART_APDMA_NR_VCHANS);
> + }
> +
> + mtkd->dma_irq = devm_kcalloc(&pdev->dev, mtkd->dma_requests,
> + sizeof(*mtkd->dma_irq), GFP_KERNEL);
> + if (!mtkd->dma_irq)
> + return -ENOMEM;
> +
> + for (i = 0; i < mtkd->dma_requests; i++) {
> + c = devm_kzalloc(mtkd->ddev.dev, sizeof(*c), GFP_KERNEL);
> + if (!c) {
> + rc = -ENODEV;
> + goto err_no_dma;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, i);
> + if (!res) {
> + rc = -ENODEV;
> + goto err_no_dma;
> + }
> +
> + c->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(c->base)) {
> + rc = PTR_ERR(c->base);
> + goto err_no_dma;
> + }
> + c->requested = false;
> + c->vc.desc_free = mtk_uart_apdma_desc_free;
> + vchan_init(&c->vc, &mtkd->ddev);
> +
> + mtkd->dma_irq[i] = platform_get_irq(pdev, i);
> + if ((int)mtkd->dma_irq[i] < 0) {
> + dev_err(&pdev->dev, "failed to get IRQ[%d]\n", i);
> + rc = -EINVAL;
> + goto err_no_dma;
> + }
> + }
> +
> + pm_runtime_enable(&pdev->dev);
> + pm_runtime_set_active(&pdev->dev);
> +
> + rc = dma_async_device_register(&mtkd->ddev);
> + if (rc)
> + goto rpm_disable;
> +
> + platform_set_drvdata(pdev, mtkd);
> +
> + /* Device-tree DMA controller registration */
> + rc = of_dma_controller_register(np, of_dma_xlate_by_chan_id, mtkd);
> + if (rc)
> + goto dma_remove;
> +
> + return rc;
> +
> +dma_remove:
> + dma_async_device_unregister(&mtkd->ddev);
> +rpm_disable:
> + pm_runtime_disable(&pdev->dev);
> +err_no_dma:
> + mtk_uart_apdma_free(mtkd);
> + return rc;
> +}
> +
> +static int mtk_uart_apdma_remove(struct platform_device *pdev)
> +{
> + struct mtk_uart_apdmadev *mtkd = platform_get_drvdata(pdev);
> +
> + if (pdev->dev.of_node)
> + of_dma_controller_free(pdev->dev.of_node);
> +
> + pm_runtime_disable(&pdev->dev);
> + pm_runtime_put_noidle(&pdev->dev);
That pm_runtime_put_noidle should be removed or it causes an
inconsistency with the probe handler.
> +
> + dma_async_device_unregister(&mtkd->ddev);
> + mtk_uart_apdma_free(mtkd);
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int mtk_uart_apdma_suspend(struct device *dev)
> +{
> + struct mtk_uart_apdmadev *mtkd = dev_get_drvdata(dev);
> +
> + if (!pm_runtime_suspended(dev))
> + clk_disable_unprepare(mtkd->clk);
> +
> + return 0;
> +}
> +
> +static int mtk_uart_apdma_resume(struct device *dev)
> +{
> + int ret;
> + struct mtk_uart_apdmadev *mtkd = dev_get_drvdata(dev);
> +
> + if (!pm_runtime_suspended(dev)) {
> + ret = clk_prepare_enable(mtkd->clk);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
> +}
> +#endif /* CONFIG_PM_SLEEP */
> +
> +#ifdef CONFIG_PM
> +static int mtk_uart_apdma_runtime_suspend(struct device *dev)
> +{
> + struct mtk_uart_apdmadev *mtkd = dev_get_drvdata(dev);
> +
> + clk_disable_unprepare(mtkd->clk);
> +
> + return 0;
> +}
> +
> +static int mtk_uart_apdma_runtime_resume(struct device *dev)
> +{
> + int ret;
> + struct mtk_uart_apdmadev *mtkd = dev_get_drvdata(dev);
> +
> + ret = clk_prepare_enable(mtkd->clk);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +#endif /* CONFIG_PM */
> +
> +static const struct dev_pm_ops mtk_uart_apdma_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(mtk_uart_apdma_suspend, mtk_uart_apdma_resume)
> + SET_RUNTIME_PM_OPS(mtk_uart_apdma_runtime_suspend,
> + mtk_uart_apdma_runtime_resume, NULL)
> +};
It probably causes a build error when CONFIG_PM is not enabled.
and use a UNIVERSAL_DEV_PM_OPS because the runtime suspend/resume and
system suspend/resume for the dma are
almost the same.
> +
> +static struct platform_driver mtk_uart_apdma_driver = {
> + .probe = mtk_uart_apdma_probe,
> + .remove = mtk_uart_apdma_remove,
> + .driver = {
> + .name = KBUILD_MODNAME,
> + .pm = &mtk_uart_apdma_pm_ops,
> + .of_match_table = of_match_ptr(mtk_uart_apdma_match),
> + },
> +};
> +
> +module_platform_driver(mtk_uart_apdma_driver);
> +
> +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> +MODULE_AUTHOR("Long Cheng <long.cheng@xxxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +
> --
> 1.7.9.5
>