[PATCH 1/1] ARM: dts: meson8b: odroidc1: add the GPIO line names
From: Martin Blumenstingl
Date: Thu Mar 28 2019 - 16:47:46 EST
This adds the GPIO line names from the schematics to get them displayed
in the debugfs output of each GPIO controller.
The schematics from Odroid-C1+ PCB revision 0.4 20150615 are used as
referenced.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
---
arch/arm/boot/dts/meson8b-odroidc1.dts | 52 ++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 3b0e0f8fbc23..0157646e3a89 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -234,7 +234,59 @@
};
};
+&gpio {
+ gpio-line-names = /* Bank GPIOX */
+ "J2 Header Pin 35", "J2 Header Pin 36",
+ "J2 Header Pin 32", "J2 Header Pin 31",
+ "J2 Header Pin 29", "J2 Header Pin 18",
+ "J2 Header Pin 22", "J2 Header Pin 16",
+ "J2 Header Pin 23", "J2 Header Pin 21",
+ "J2 Header Pin 19", "J2 Header Pin 33",
+ "J2 Header Pin 8", "J2 Header Pin 10",
+ "J2 Header Pin 15", "J2 Header Pin 13",
+ "J2 Header Pin 24", "J2 Header Pin 26",
+ /* Bank GPIOY */
+ "Revision (upper)", "Revision (lower)",
+ "J2 Header Pin 7", "", "J2 Header Pin 12",
+ "J2 Header Pin 11", "", "", "",
+ "TFLASH_VDD_EN", "", "",
+ /* Bank GPIODV */
+ "VCCK_PWM (PWM_C)", "I2CA_SDA", "I2CA_SCL",
+ "I2CB_SDA", "I2CB_SCL", "VDDEE_PWM (PWM_D)",
+ "",
+ /* Bank GPIOH */
+ "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL",
+ "ETH_PHY_INTR", "ETH_PHY_NRST", "ETH_TXD1",
+ "ETH_TXD0", "ETH_TXD3", "ETH_TXD2",
+ "ETH_RGMII_TX_CLK",
+ /* Bank CARD */
+ "SD_DATA1 (SDB_D1)", "SD_DATA0 (SDB_D0)",
+ "SD_CLK", "SD_CMD", "SD_DATA3 (SDB_D3)",
+ "SD_DATA2 (SDB_D2)", "SD_CDN (SD_DET_N)",
+ /* Bank BOOT */
+ "SDC_D0 (EMMC)", "SDC_D1 (EMMC)",
+ "SDC_D2 (EMMC)", "SDC_D3 (EMMC)",
+ "SDC_D4 (EMMC)", "SDC_D5 (EMMC)",
+ "SDC_D6 (EMMC)", "SDC_D7 (EMMC)",
+ "SDC_CLK (EMMC)", "SDC_RSTn (EMMC)",
+ "SDC_CMD (EMMC)", "BOOT_SEL", "", "", "",
+ "", "", "", "",
+ /* Bank DIF */
+ "ETH_RXD1", "ETH_RXD0", "ETH_RX_DV",
+ "RGMII_RX_CLK", "ETH_RXD3", "ETH_RXD2",
+ "ETH_TXEN", "ETH_PHY_REF_CLK_25MOUT",
+ "ETH_MDC", "ETH_MDIO";
+};
+
&gpio_ao {
+ gpio-line-names = "UART TX", "UART RX", "",
+ "TF_3V3N_1V8_EN", "USB_HUB_RST_N",
+ "USB_OTG_PWREN", "J7 Header Pin 2",
+ "IR_IN", "J7 Header Pin 4",
+ "J7 Header Pin 6", "J7 Header Pin 5",
+ "J7 Header Pin 7", "HDMI_CEC",
+ "SYS_LED", "", "";
+
/*
* WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
* to be turned high in order to be detected by the USB Controller.
--
2.21.0