[PATCH v2 3/3] ARM: dts: imx50: Add Kobo Aura DTS

From: Jonathan NeuschÃfer
Date: Sun Mar 31 2019 - 15:16:51 EST

The Kobo Aura is an e-book reader released in 2013.

With the devicetree in its current state, the kernel will boot and run
for about ten seconds. To solve this, the embedded controller needs to
be told that the system should stay powered on. This will be done in a
later patchset.

- The IOMUXC mode bits for the SD interfaces were taken from the
vendor's U-Boot fork.
- The bus width of the eMMC is 4 bits in the vendor kernel, but I
achieved better performance with 8 bits.
- The SDIO clock frequency for the WiFi chip is 25MHz in the vendor
kernel, but the WiFi chip (BCM43362) supports 50MHz, which works
reliably on this board and gives slightly better performance.
- The I2C pins' IOMUXC settings come from the vendor's U-Boot fork.

Signed-off-by: Jonathan NeuschÃfer <j.neuschaefer@xxxxxxx>
---

v2:
- Squash patch 4 ("ARM: dts: imx50-kobo-aura: Enable USB support")
- Sort pinctrl nodes alphabetically, as suggested by Shawn Guo
- Sort labeled nodes alphabetically, as suggested by Shawn Guo
- Make "status" the last property, as suggested by Shawn Guo
- Use KEY_RESERVED and EV_SW, as suggested by Shawn Guo
- Remove newlines between properties, as suggested by Shawn Guo

v1:
https://lore.kernel.org/lkml/20190319152421.16179-3-j.neuschaefer@xxxxxxx/
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx50-kobo-aura.dts | 258 ++++++++++++++++++++++++++
2 files changed, 260 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx50-kobo-aura.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aeaf3298..0c85156c552b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -363,7 +363,8 @@ dtb-$(CONFIG_SOC_IMX35) += \
imx35-eukrea-mbimxsd35-baseboard.dtb \
imx35-pdk.dtb
dtb-$(CONFIG_SOC_IMX50) += \
- imx50-evk.dtb
+ imx50-evk.dtb \
+ imx50-kobo-aura.dtb
dtb-$(CONFIG_SOC_IMX51) += \
imx51-apf51.dtb \
imx51-apf51dev.dtb \
diff --git a/arch/arm/boot/dts/imx50-kobo-aura.dts b/arch/arm/boot/dts/imx50-kobo-aura.dts
new file mode 100644
index 000000000000..a0eaf869b913
--- /dev/null
+++ b/arch/arm/boot/dts/imx50-kobo-aura.dts
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2019 Jonathan NeuschÃfer
+//
+// The Kobo Aura e-book reader, model N514. The mainboard is marked as E606F0B.
+
+/dts-v1/;
+#include "imx50.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Kobo Aura (N514)";
+ compatible = "kobo,aura", "fsl,imx50";
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@70000000 {
+ device_type = "memory";
+ reg = <0x70000000 0x10000000>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ on {
+ label = "kobo_aura:orange:on";
+ gpios = <&gpio6 24 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiokeys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ hallsensor {
+ label = "Hallsensor";
+ gpios = <&gpio5 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESERVED>;
+ linux,input-type = <EV_SW>;
+ };
+
+ frontlight {
+ label = "Frontlight";
+ gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_DISPLAYTOGGLE>;
+ };
+ };
+
+ sd2_pwrseq: pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd2_reset>;
+ reset-gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+ };
+
+ sd2_vmmc: gpio-regulator {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd2_vmmc>;
+ regulator-name = "vmmc";
+ states = <3300000 0>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-gpio = <&gpio4 12 GPIO_ACTIVE_LOW>;
+ startup-delay-us = <100000>;
+ };
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd1>;
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ cd-gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ status = "okay";
+
+ /* External ÂSD card */
+};
+
+&esdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd2>;
+ bus-width = <4>;
+ max-frequency = <50000000>;
+ disable-wp;
+ mmc-pwrseq = <&sd2_pwrseq>;
+ vmmc-supply = <&sd2_vmmc>;
+ status = "okay";
+
+ /* CyberTan WC121 SDIO WiFi (BCM43362) */
+};
+
+&esdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sd3>;
+ bus-width = <8>;
+ non-removable;
+ max-frequency = <50000000>;
+ disable-wp;
+ status = "okay";
+
+ /* Internal eMMC */
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ /* TODO: ektf2132 touch controller at 0x15 */
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ /* TODO: TPS65185 PMIC for E Ink at 0x68 */
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ /* TODO: embedded controller at 0x43 */
+};
+
+&iomuxc {
+ pinctrl_gpiokeys: gpiokeys {
+ fsl,pins = <
+ MX50_PAD_CSPI_MISO__GPIO4_10 0x0
+ MX50_PAD_SD2_D7__GPIO5_15 0x0
+ MX50_PAD_KEY_ROW0__GPIO4_1 0x0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1 {
+ fsl,pins = <
+ MX50_PAD_I2C1_SCL__I2C1_SCL 0x400001fd
+ MX50_PAD_I2C1_SDA__I2C1_SDA 0x400001fd
+ >;
+ };
+
+ pinctrl_i2c2: i2c2 {
+ fsl,pins = <
+ MX50_PAD_I2C2_SCL__I2C2_SCL 0x400001fd
+ MX50_PAD_I2C2_SDA__I2C2_SDA 0x400001fd
+ >;
+ };
+
+ pinctrl_i2c3: i2c3 {
+ fsl,pins = <
+ MX50_PAD_I2C3_SCL__I2C3_SCL 0x400001fd
+ MX50_PAD_I2C3_SDA__I2C3_SDA 0x400001fd
+ >;
+ };
+
+ pinctrl_leds: leds {
+ fsl,pins = <
+ MX50_PAD_PWM1__GPIO6_24 0x0
+ >;
+ };
+
+ pinctrl_sd1: sd1 {
+ fsl,pins = <
+ MX50_PAD_SD1_CMD__ESDHC1_CMD 0x1e4
+ MX50_PAD_SD1_CLK__ESDHC1_CLK 0xd4
+ MX50_PAD_SD1_D0__ESDHC1_DAT0 0x1d4
+ MX50_PAD_SD1_D1__ESDHC1_DAT1 0x1d4
+ MX50_PAD_SD1_D2__ESDHC1_DAT2 0x1d4
+ MX50_PAD_SD1_D3__ESDHC1_DAT3 0x1d4
+
+ MX50_PAD_SD2_CD__GPIO5_17 0x0
+ >;
+ };
+
+ pinctrl_sd2: sd2 {
+ fsl,pins = <
+ MX50_PAD_SD2_CMD__ESDHC2_CMD 0x1e4
+ MX50_PAD_SD2_CLK__ESDHC2_CLK 0xd4
+ MX50_PAD_SD2_D0__ESDHC2_DAT0 0x1d4
+ MX50_PAD_SD2_D1__ESDHC2_DAT1 0x1d4
+ MX50_PAD_SD2_D2__ESDHC2_DAT2 0x1d4
+ MX50_PAD_SD2_D3__ESDHC2_DAT3 0x1d4
+ >;
+ };
+
+ pinctrl_sd2_reset: sd2-reset {
+ fsl,pins = <
+ MX50_PAD_ECSPI2_MOSI__GPIO4_17 0x0
+ >;
+ };
+
+ pinctrl_sd2_vmmc: sd2-vmmc {
+ fsl,pins = <
+ MX50_PAD_ECSPI1_SCLK__GPIO4_12 0x0
+ >;
+ };
+
+ pinctrl_sd3: sd3 {
+ fsl,pins = <
+ MX50_PAD_SD3_CMD__ESDHC3_CMD 0x1e4
+ MX50_PAD_SD3_CLK__ESDHC3_CLK 0xd4
+ MX50_PAD_SD3_D0__ESDHC3_DAT0 0x1d4
+ MX50_PAD_SD3_D1__ESDHC3_DAT1 0x1d4
+ MX50_PAD_SD3_D2__ESDHC3_DAT2 0x1d4
+ MX50_PAD_SD3_D3__ESDHC3_DAT3 0x1d4
+ MX50_PAD_SD3_D4__ESDHC3_DAT4 0x1d4
+ MX50_PAD_SD3_D5__ESDHC3_DAT5 0x1d4
+ MX50_PAD_SD3_D6__ESDHC3_DAT6 0x1d4
+ MX50_PAD_SD3_D7__ESDHC3_DAT7 0x1d4
+ >;
+ };
+
+ pinctrl_uart2: uart2 {
+ fsl,pins = <
+ MX50_PAD_UART2_TXD__UART2_TXD_MUX 0x1e4
+ MX50_PAD_UART2_RXD__UART2_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_usbphy: usbphy {
+ fsl,pins = <
+ MX50_PAD_ECSPI2_SS0__GPIO4_19 0x0
+ >;
+ };
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg {
+ phy_type = "utmi_wide";
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbphy>;
+ vbus-detect-gpio = <&gpio4 19 GPIO_ACTIVE_LOW>;
+};
--
2.20.1