[PATCH v2 5/5] ARM: dts: sun50i: h6: Introduce Beelink GS1 board

From: ClÃment PÃron
Date: Fri Apr 05 2019 - 08:21:44 EST

Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply

Signed-off-by: ClÃment PÃron <peron.clem@xxxxxxxxx>
---

Thanks to Jagan and Icenowy, most of this devicetree is taken from their works on
the OrangePi One Plus and Pine H64.

Changes in v2 (Thanks to Maxime Ripard):
- move MMC pinctrl to SOC dtsi
- add board to Sunxi YAML file
- add PIO/R_PIO regulators
- remove always_on from SDIO regulators


.../devicetree/bindings/arm/sunxi.yaml | 5 +
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-h6-beelink-gs1.dts | 256 ++++++++++++++++++
3 files changed, 262 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 11563d3f7c65..9ab9b266881d 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -136,6 +136,11 @@ properties:
- const: lemaker,bananapro
- const: allwinner,sun7i-a20

+ - description: Beelink GS1
+ items:
+ - const: azw,beelink-gs1
+ - const: allwinner,sun50i-h6
+
- description: Beelink X2
items:
- const: roofull,beelink-x2
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index e4dce2f6fa3a..2dd806a3d5c9 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-beelink-gs1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
new file mode 100644
index 000000000000..d820a138522b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2019 ClÃment PÃron <peron.clem@xxxxxxxxx>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Beelink GS1";
+ compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ label = "beelink:white:power";
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
+ default-state = "on";
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the DC jack */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <&reg_aldo2>;
+ allwinner,rx-delay-ps = <0>;
+ allwinner,tx-delay-ps = <0>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <&reg_cldo1>;
+ vqmmc-supply = <&reg_bldo2>;
+ non-removable;
+ cap-mmc-hw-reset;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pd-supply = <&reg_cldo1>;
+ vcc-pg-supply = <&reg_aldo1>;
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp805: pmic@36 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x36>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+ vina-supply = <&reg_vcc5v>;
+ vinb-supply = <&reg_vcc5v>;
+ vinc-supply = <&reg_vcc5v>;
+ vind-supply = <&reg_vcc5v>;
+ vine-supply = <&reg_vcc5v>;
+ aldoin-supply = <&reg_vcc5v>;
+ bldoin-supply = <&reg_vcc5v>;
+ cldoin-supply = <&reg_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ regulator-enable-ramp-delay = <100000>;
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc25-dram";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-1";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&r_pio {
+ vcc-pl-supply = <&reg_aldo1>;
+ vcc-pm-supply = <&reg_aldo1>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usb2otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb2phy {
+ usb0_vbus-supply = <&reg_vcc5v>;
+ status = "okay";
+};
--
2.17.1