Re: [PATCH v5 1/7] dt-bindings: Add panel-timing subnode to simple-panel

[Boris Brezillon]

On Mon,  1 Apr 2019 10:17:18 -0700
Douglas Anderson <dianders@xxxxxxxxxxxx> wrote:

> From: Sean Paul <seanpaul@xxxxxxxxxxxx>
> 
> This patch adds a new subnode to simple-panel allowing us to override
> the typical timing expressed in the panel's display_timing.
> 
> Changes in v2:
>  - Split out the binding into a new patch (Rob)
>  - display-timings is a new section (Rob)
>  - Use the full display-timings subnode instead of picking the timing
>    out (Rob/Thierry)
> Changes in v3:
>  - Go back to using the timing subnode directly, but rename to
>    panel-timing (Rob)
> Changes in v4:
>  - Simplify desc. for when override should be used (Thierry/Laurent)
>  - Removed Rob H review since it's been a year and wording changed
> Changes in v5:
>  - Removed bit about OS may ignore (Rob/Ezequiel)
> 
> Cc: Doug Anderson <dianders@xxxxxxxxxxxx>
> Cc: Eric Anholt <eric@xxxxxxxxxx>
> Cc: Heiko Stuebner <heiko@xxxxxxxxx>
> Cc: Jeffy Chen <jeffy.chen@xxxxxxxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: StÃphane Marchesin <marcheu@xxxxxxxxxxxx>
> Cc: Thierry Reding <thierry.reding@xxxxxxxxx>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
> Cc: linux-rockchip@xxxxxxxxxxxxxxxxxxx
> Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>

Reviewed-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>

> ---
> 
>  .../bindings/display/panel/simple-panel.txt   | 22 +++++++++++++++++++
>  1 file changed, 22 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
> index b2b872c710f2..93882268c0b9 100644
> --- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
> +++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
> @@ -15,6 +15,16 @@ Optional properties:
>    (hot plug detect) signal, but the signal isn't hooked up so we should
>    hardcode the max delay from the panel spec when powering up the panel.
>  
> +panel-timing subnode
> +--------------------
> +
> +This optional subnode is for devices which require a mode differing
> +from the panel's "typical" display timing.
> +
> +Format information on the panel-timing subnode can be found in
> +display-timing.txt.
> +
> +
>  Example:
>  
>  	panel: panel {
> @@ -25,4 +35,16 @@ Example:
>  		enable-gpios = <&gpio 90 0>;
>  
>  		backlight = <&backlight>;
> +
> +		panel-timing {
> +			clock-frequency = <266604720>;
> +			hactive = <2400>;
> +			hfront-porch = <48>;
> +			hback-porch = <84>;
> +			hsync-len = <32>;
> +			vactive = <1600>;
> +			vfront-porch = <3>;
> +			vback-porch = <120>;
> +			vsync-len = <10>;
> +		};
>  	};