[PATCH v3 14/21] docs: hwmon: dme1737, vt1211: convert to ReST format
From: Mauro Carvalho Chehab
Date: Wed Apr 17 2019 - 05:48:12 EST
Convert dme1737 and vt1211 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@xxxxxxxxxx>
---
Documentation/hwmon/dme1737 | 88 ++++++++++++++++++++++++++-----------
Documentation/hwmon/vt1211 | 84 +++++++++++++++++++++--------------
2 files changed, 114 insertions(+), 58 deletions(-)
diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737
index 4d2935145a1c..82fcbc6b2b43 100644
--- a/Documentation/hwmon/dme1737
+++ b/Documentation/hwmon/dme1737
@@ -2,21 +2,37 @@ Kernel driver dme1737
=====================
Supported chips:
+
* SMSC DME1737 and compatibles (like Asus A8000)
+
Prefix: 'dme1737'
+
Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+
Datasheet: Provided by SMSC upon request and under NDA
+
* SMSC SCH3112, SCH3114, SCH3116
+
Prefix: 'sch311x'
+
Addresses scanned: none, address read from Super-I/O config space
+
Datasheet: Available on the Internet
+
* SMSC SCH5027
+
Prefix: 'sch5027'
+
Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+
Datasheet: Provided by SMSC upon request and under NDA
+
* SMSC SCH5127
+
Prefix: 'sch5127'
+
Addresses scanned: none, address read from Super-I/O config space
+
Datasheet: Provided by SMSC upon request and under NDA
Authors:
@@ -26,11 +42,14 @@ Authors:
Module Parameters
-----------------
-* force_start: bool Enables the monitoring of voltage, fan and temp inputs
+* force_start: bool
+ Enables the monitoring of voltage, fan and temp inputs
and PWM output control functions. Using this parameter
shouldn't be required since the BIOS usually takes care
of this.
-* probe_all_addr: bool Include non-standard LPC addresses 0x162e and 0x164e
+
+* probe_all_addr: bool
+ Include non-standard LPC addresses 0x162e and 0x164e
when probing for ISA devices. This is required for the
following boards:
- VIA EPIA SN18000
@@ -70,7 +89,8 @@ scaling resistors. The values returned by the driver therefore reflect true
millivolts and don't need scaling. The voltage inputs are mapped as follows
(the last column indicates the input ranges):
-DME1737, A8000:
+DME1737, A8000::
+
in0: +5VTR (+5V standby) 0V - 6.64V
in1: Vccp (processor core) 0V - 3V
in2: VCC (internal +3.3V) 0V - 4.38V
@@ -79,7 +99,8 @@ DME1737, A8000:
in5: VTR (+3.3V standby) 0V - 4.38V
in6: Vbat (+3.0V) 0V - 4.38V
-SCH311x:
+SCH311x::
+
in0: +2.5V 0V - 3.32V
in1: Vccp (processor core) 0V - 2V
in2: VCC (internal +3.3V) 0V - 4.38V
@@ -88,7 +109,8 @@ SCH311x:
in5: VTR (+3.3V standby) 0V - 4.38V
in6: Vbat (+3.0V) 0V - 4.38V
-SCH5027:
+SCH5027::
+
in0: +5VTR (+5V standby) 0V - 6.64V
in1: Vccp (processor core) 0V - 3V
in2: VCC (internal +3.3V) 0V - 4.38V
@@ -97,7 +119,8 @@ SCH5027:
in5: VTR (+3.3V standby) 0V - 4.38V
in6: Vbat (+3.0V) 0V - 4.38V
-SCH5127:
+SCH5127::
+
in0: +2.5 0V - 3.32V
in1: Vccp (processor core) 0V - 3V
in2: VCC (internal +3.3V) 0V - 4.38V
@@ -119,7 +142,7 @@ Celsius. The chip also features offsets for all 3 temperature inputs which -
when programmed - get added to the input readings. The chip does all the
scaling by itself and the driver therefore reports true temperatures that don't
need any user-space adjustments. The temperature inputs are mapped as follows
-(the last column indicates the input ranges):
+(the last column indicates the input ranges)::
temp1: Remote diode 1 (3904 type) temperature -127C - +127C
temp2: DME1737 internal temperature -127C - +127C
@@ -171,6 +194,7 @@ pwm[1-3]_auto_pwm_min, respectively. The thermal thresholds of the zones are
programmed via zone[1-3]_auto_point[1-3]_temp and
zone[1-3]_auto_point1_temp_hyst:
+ =============================== =======================================
pwm[1-3]_auto_point2_pwm full-speed duty-cycle (255, i.e., 100%)
pwm[1-3]_auto_point1_pwm low-speed duty-cycle
pwm[1-3]_auto_pwm_min min-speed duty-cycle
@@ -179,6 +203,7 @@ zone[1-3]_auto_point1_temp_hyst:
zone[1-3]_auto_point2_temp full-speed temp
zone[1-3]_auto_point1_temp low-speed temp
zone[1-3]_auto_point1_temp_hyst min-speed temp
+ =============================== =======================================
The chip adjusts the output duty-cycle linearly in the range of auto_point1_pwm
to auto_point2_pwm if the temperature of the associated zone is between
@@ -192,17 +217,21 @@ all PWM outputs are set to 100% duty-cycle.
Following is another representation of how the chip sets the output duty-cycle
based on the temperature of the associated thermal zone:
- Duty-Cycle Duty-Cycle
- Temperature Rising Temp Falling Temp
- ----------- ----------- ------------
+ =============== =============== =================
+ Temperature Duty-Cycle Duty-Cycle
+ Rising Temp Falling Temp
+ =============== =============== =================
full-speed full-speed full-speed
- < linearly adjusted duty-cycle >
+ - < linearly -
+ adjusted
+ duty-cycle >
low-speed low-speed low-speed
- min-speed low-speed
+ - min-speed low-speed
min-speed min-speed min-speed
- min-speed min-speed
+ - min-speed min-speed
+ =============== =============== =================
Sysfs Attributes
@@ -211,8 +240,9 @@ Sysfs Attributes
Following is a list of all sysfs attributes that the driver provides, their
permissions and a short description:
+=============================== ======= =======================================
Name Perm Description
----- ---- -----------
+=============================== ======= =======================================
cpu0_vid RO CPU core reference voltage in
millivolts.
vrm RW Voltage regulator module version
@@ -242,9 +272,10 @@ temp[1-3]_fault RO Temp input fault. Returns 1 if the chip
zone[1-3]_auto_channels_temp RO Temperature zone to temperature input
mapping. This attribute is a bitfield
and supports the following values:
- 1: temp1
- 2: temp2
- 4: temp3
+
+ - 1: temp1
+ - 2: temp2
+ - 4: temp3
zone[1-3]_auto_point1_temp_hyst RW Auto PWM temp point1 hysteresis. The
output of the corresponding PWM is set
to the pwm_auto_min value if the temp
@@ -275,9 +306,10 @@ pmw[1-3,5-6] RO/RW Duty-cycle of PWM output. Supported
manual mode.
pwm[1-3]_enable RW Enable of PWM outputs 1-3. Supported
values are:
- 0: turned off (output @ 100%)
- 1: manual mode
- 2: automatic mode
+
+ - 0: turned off (output @ 100%)
+ - 1: manual mode
+ - 2: automatic mode
pwm[5-6]_enable RO Enable of PWM outputs 5-6. Always
returns 1 since these 2 outputs are
hard-wired to manual mode.
@@ -294,11 +326,12 @@ pmw[1-3]_ramp_rate RW Ramp rate of PWM output. Determines how
pwm[1-3]_auto_channels_zone RW PWM output to temperature zone mapping.
This attribute is a bitfield and
supports the following values:
- 1: zone1
- 2: zone2
- 4: zone3
- 6: highest of zone[2-3]
- 7: highest of zone[1-3]
+
+ - 1: zone1
+ - 2: zone2
+ - 4: zone3
+ - 6: highest of zone[2-3]
+ - 7: highest of zone[1-3]
pwm[1-3]_auto_pwm_min RW Auto PWM min pwm. Minimum PWM duty-
cycle. Supported values are 0 or
auto_point1_pwm.
@@ -307,12 +340,14 @@ pwm[1-3]_auto_point1_pwm RW Auto PWM pwm point. Auto_point1 is the
pwm[1-3]_auto_point2_pwm RO Auto PWM pwm point. Auto_point2 is the
full-speed duty-cycle which is hard-
wired to 255 (100% duty-cycle).
+=============================== ======= =======================================
Chip Differences
----------------
+======================= ======= ======= ======= =======
Feature dme1737 sch311x sch5027 sch5127
--------------------------------------------------------
+======================= ======= ======= ======= =======
temp[1-3]_offset yes yes
vid yes
zone3 yes yes yes
@@ -326,3 +361,4 @@ pwm5 opt opt
fan6 opt opt
pwm6 opt opt
in7 yes
+======================= ======= ======= ======= =======
diff --git a/Documentation/hwmon/vt1211 b/Documentation/hwmon/vt1211
index 77fa633b97a8..ddbcde7dd642 100644
--- a/Documentation/hwmon/vt1211
+++ b/Documentation/hwmon/vt1211
@@ -2,9 +2,13 @@ Kernel driver vt1211
====================
Supported chips:
+
* VIA VT1211
+
Prefix: 'vt1211'
+
Addresses scanned: none, address read from Super-I/O config space
+
Datasheet: Provided by VIA upon request and under NDA
Authors: Juerg Haefliger <juergh@xxxxxxxxx>
@@ -19,14 +23,17 @@ technical support.
Module Parameters
-----------------
-* uch_config: int Override the BIOS default universal channel (UCH)
+
+* uch_config: int
+ Override the BIOS default universal channel (UCH)
configuration for channels 1-5.
Legal values are in the range of 0-31. Bit 0 maps to
UCH1, bit 1 maps to UCH2 and so on. Setting a bit to 1
enables the thermal input of that particular UCH and
setting a bit to 0 enables the voltage input.
-* int_mode: int Override the BIOS default temperature interrupt mode.
+* int_mode: int
+ Override the BIOS default temperature interrupt mode.
The only possible value is 0 which forces interrupt
mode 0. In this mode, any pending interrupt is cleared
when the status register is read but is regenerated as
@@ -55,8 +62,9 @@ connected to the PWM outputs of the VT1211 :-().
The following table shows the relationship between the vt1211 inputs and the
sysfs nodes.
+=============== ============== =========== ================================
Sensor Voltage Mode Temp Mode Default Use (from the datasheet)
------- ------------ --------- --------------------------------
+=============== ============== =========== ================================
Reading 1 temp1 Intel thermal diode
Reading 3 temp2 Internal thermal diode
UCH1/Reading2 in0 temp3 NTC type thermistor
@@ -65,6 +73,7 @@ UCH3 in2 temp5 VccP (processor core)
UCH4 in3 temp6 +5V
UCH5 in4 temp7 +12V
+3.3V in5 Internal VCC (+3.3V)
+=============== ============== =========== ================================
Voltage Monitoring
@@ -82,19 +91,22 @@ follows. And this is of course totally dependent on the actual board
implementation :-) You will have to find documentation for your own
motherboard and edit sensors.conf accordingly.
- Expected
+============= ====== ====== ========= ============
+ Expected
Voltage R1 R2 Divider Raw Value
------------------------------------------------
+============= ====== ====== ========= ============
+2.5V 2K 10K 1.2 2083 mV
-VccP --- --- 1.0 1400 mV (1)
+VccP --- --- 1.0 1400 mV [1]_
+5V 14K 10K 2.4 2083 mV
+12V 47K 10K 5.7 2105 mV
-+3.3V (int) 2K 3.4K 1.588 3300 mV (2)
++3.3V (int) 2K 3.4K 1.588 3300 mV [2]_
+3.3V (ext) 6.8K 10K 1.68 1964 mV
+============= ====== ====== ========= ============
-(1) Depending on the CPU (1.4V is for a VIA C3 Nehemiah).
-(2) R1 and R2 for 3.3V (int) are internal to the VT1211 chip and the driver
- performs the scaling and returns the properly scaled voltage value.
+.. [1] Depending on the CPU (1.4V is for a VIA C3 Nehemiah).
+
+.. [2] R1 and R2 for 3.3V (int) are internal to the VT1211 chip and the driver
+ performs the scaling and returns the properly scaled voltage value.
Each measured voltage has an associated low and high limit which triggers an
alarm when crossed.
@@ -124,35 +136,37 @@ compute temp1 (@-Offset)/Gain, (@*Gain)+Offset
According to the VIA VT1211 BIOS porting guide, the following gain and offset
values should be used:
+=============== ======== ===========
Diode Type Offset Gain
----------- ------ ----
+=============== ======== ===========
Intel CPU 88.638 0.9528
- 65.000 0.9686 *)
+ 65.000 0.9686 [3]_
VIA C3 Ezra 83.869 0.9528
VIA C3 Ezra-T 73.869 0.9528
+=============== ======== ===========
-*) This is the formula from the lm_sensors 2.10.0 sensors.conf file. I don't
-know where it comes from or how it was derived, it's just listed here for
-completeness.
+.. [3] This is the formula from the lm_sensors 2.10.0 sensors.conf file. I don't
+ know where it comes from or how it was derived, it's just listed here for
+ completeness.
Temp3-temp7 support NTC thermistors. For these channels, the driver returns
the voltages as seen at the individual pins of UCH1-UCH5. The voltage at the
pin (Vpin) is formed by a voltage divider made of the thermistor (Rth) and a
-scaling resistor (Rs):
+scaling resistor (Rs)::
-Vpin = 2200 * Rth / (Rs + Rth) (2200 is the ADC max limit of 2200 mV)
+ Vpin = 2200 * Rth / (Rs + Rth) (2200 is the ADC max limit of 2200 mV)
The equation for the thermistor is as follows (google it if you want to know
-more about it):
+more about it)::
-Rth = Ro * exp(B * (1 / T - 1 / To)) (To is 298.15K (25C) and Ro is the
- nominal resistance at 25C)
+ Rth = Ro * exp(B * (1 / T - 1 / To)) (To is 298.15K (25C) and Ro is the
+ nominal resistance at 25C)
Mingling the above two equations and assuming Rs = Ro and B = 3435 yields the
-following formula for sensors.conf:
+following formula for sensors.conf::
-compute tempx 1 / (1 / 298.15 - (` (2200 / @ - 1)) / 3435) - 273.15,
- 2200 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
+ compute tempx 1 / (1 / 298.15 - (` (2200 / @ - 1)) / 3435) - 273.15,
+ 2200 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
Fan Speed Control
@@ -176,31 +190,37 @@ registers in the VT1211 and programming one set is sufficient (actually only
the first set pwm1_auto_point[1-4]_temp is writable, the second set is
read-only).
+========================== =========================================
PWM Auto Point PWM Output Duty-Cycle
-------------------------------------------------
+========================== =========================================
pwm[1-2]_auto_point4_pwm full speed duty-cycle (hard-wired to 255)
pwm[1-2]_auto_point3_pwm high speed duty-cycle
pwm[1-2]_auto_point2_pwm low speed duty-cycle
pwm[1-2]_auto_point1_pwm off duty-cycle (hard-wired to 0)
+========================== =========================================
+========================== =================
Temp Auto Point Thermal Threshold
----------------------------------------------
+========================== =================
pwm[1-2]_auto_point4_temp full speed temp
pwm[1-2]_auto_point3_temp high speed temp
pwm[1-2]_auto_point2_temp low speed temp
pwm[1-2]_auto_point1_temp off temp
+========================== =================
Long story short, the controller implements the following algorithm to set the
PWM output duty-cycle based on the input temperature:
-Thermal Threshold Output Duty-Cycle
- (Rising Temp) (Falling Temp)
-----------------------------------------------------------
- full speed duty-cycle full speed duty-cycle
+=================== ======================= ========================
+Thermal Threshold Output Duty-Cycle Output Duty-Cycle
+ (Rising Temp) (Falling Temp)
+=================== ======================= ========================
+- full speed duty-cycle full speed duty-cycle
full speed temp
- high speed duty-cycle full speed duty-cycle
+- high speed duty-cycle full speed duty-cycle
high speed temp
- low speed duty-cycle high speed duty-cycle
+- low speed duty-cycle high speed duty-cycle
low speed temp
- off duty-cycle low speed duty-cycle
+- off duty-cycle low speed duty-cycle
off temp
+=================== ======================= ========================
--
2.20.1