Re: [PATCH v3 00/3] MIPS: SGI-IP27 rework part2

[Bjorn Helgaas]

Hi Thomas,

On Tue, Mar 19, 2019 at 04:47:49PM +0100, Thomas Bogendoerfer wrote:
> SGI IP27 (Origin/Onyx2) and SGI IP30 (Octane) have a similair
> architecture and share some hardware (ioc3/bridge). To share
> the software parts this patchset reworks SGI IP27 interrupt
> and pci bridge code. By using features Linux gained during the
> many years since SGI IP27 code was integrated this even results
> in code reduction and IMHO cleaner code.
> 
> Tests have been done on a two module O200 (4 CPUs) and an
> Origin 2000 (8 CPUs).

Thanks for doing all this work!  It seems like it basically converts
some of the SGI PCI code to the structure typical of current host
controller drivers and moves it to drivers/pci/controller, which all
seems great to me.

The patches were kind of in limbo as far as Patchwork.  Lorenzo
handles the native host controller drivers, so I just delegated them
to him, so now they should be on his radar.

Bjorn

> My next step in integrating SGI IP30 support is splitting ioc3eth
> into a MFD and subdevice drivers, which will be submitted soon.
> 
> Changes in v3:
> 
> - dropped patches accepted by Paul
> - moved IP27 specific __phys_to_dma/__dma_to_phys into its own file
> - moved pcibios_to_node into IP27 specific file
> - moved PCI bus address resources setup out of pci-xtalk code into
>   IP27 specific code
> - dropped bit from hub_irq_data and use hwirq from irq_data
> - introduced intr_addr for setting up bridge interrupts (IP30 preperation)
> 
> Changes in v2:
> 
> - replaced HUB_L/HUB_S by __raw_readq/__raw_writeq
> - removed union bridge_ate
> - replaced remaing fields in slice_data by per_cpu data
> - use generic_handle_irq instead of do_IRQ
> - use hierarchy irq domain for stacking bridge and hub interrupt
> - moved __dma_to_phys/__phy_to_dma to mach-ip27/dma-direct.h
> - use dev_to_node() for pcibus_to_node() implementation
> 
> Thomas Bogendoerfer (3):
>   MIPS: SGI-IP27: move IP27 specific code out of pci-ip27.c into new
>     file
>   MIPS: SGI-IP27: use generic PCI driver
>   MIPS: SGI-IP27: abstract chipset irq from bridge
> 
>  arch/mips/Kconfig                          |   3 +
>  arch/mips/include/asm/mach-ip27/topology.h |  11 +-
>  arch/mips/include/asm/pci/bridge.h         |  14 +-
>  arch/mips/include/asm/sn/irq_alloc.h       |  11 +
>  arch/mips/include/asm/xtalk/xtalk.h        |   9 -
>  arch/mips/pci/Makefile                     |   1 -
>  arch/mips/pci/ops-bridge.c                 | 302 --------------
>  arch/mips/pci/pci-ip27.c                   | 214 ----------
>  arch/mips/sgi-ip27/Makefile                |   4 +-
>  arch/mips/sgi-ip27/ip27-init.c             |   2 +
>  arch/mips/sgi-ip27/ip27-irq.c              | 191 ++++-----
>  arch/mips/sgi-ip27/ip27-pci.c              |  30 ++
>  arch/mips/sgi-ip27/ip27-xtalk.c            |  61 ++-
>  drivers/pci/controller/Kconfig             |   3 +
>  drivers/pci/controller/Makefile            |   1 +
>  drivers/pci/controller/pci-xtalk-bridge.c  | 610 +++++++++++++++++++++++++++++
>  include/linux/platform_data/xtalk-bridge.h |  22 ++
>  17 files changed, 822 insertions(+), 667 deletions(-)
>  create mode 100644 arch/mips/include/asm/sn/irq_alloc.h
>  delete mode 100644 arch/mips/pci/ops-bridge.c
>  delete mode 100644 arch/mips/pci/pci-ip27.c
>  create mode 100644 arch/mips/sgi-ip27/ip27-pci.c
>  create mode 100644 drivers/pci/controller/pci-xtalk-bridge.c
>  create mode 100644 include/linux/platform_data/xtalk-bridge.h
> 
> -- 
> 2.13.7
>