Re: [PATCH v2 2/7] clk: bcm283x: add driver interfacing with Raspberry Pi's firmware

[Stefan Wahren]

Hi Nicolas,

Am 06.06.19 um 16:22 schrieb Nicolas Saenz Julienne:
> Raspberry Pi's firmware offers an interface though which update it's
> clock's frequencies. This is specially useful in order to change the CPU
> clock (pllb_arm) which is 'owned' by the firmware and we're unable to
> scale using the register interface provided by clk-bcm2835.
>
> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx>
> Acked-by: Eric Anholt <eric@xxxxxxxxxx>
>
> ---
>
> Changes since v1:
>   - Use BIT()
>   - Add Kconfig entry, with compile test
>   - remove prepare/unprepare
>   - Fix uninitialized init.name in pllb registration
>   - Add MODULE_ALIAS()
>   - Use determine_rate() instead of round_rate()
>   - Add small introduction explaining need for driver
>
>  drivers/clk/bcm/Kconfig           |   7 +
>  drivers/clk/bcm/Makefile          |   1 +
>  drivers/clk/bcm/clk-raspberrypi.c | 302 ++++++++++++++++++++++++++++++
>  3 files changed, 310 insertions(+)
>  create mode 100644 drivers/clk/bcm/clk-raspberrypi.c
>
> diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
> index 29ee7b776cd4..a4a2775d65e1 100644
> --- a/drivers/clk/bcm/Kconfig
> +++ b/drivers/clk/bcm/Kconfig
> @@ -64,3 +64,10 @@ config CLK_BCM_SR
>  	default ARCH_BCM_IPROC
>  	help
>  	  Enable common clock framework support for the Broadcom Stingray SoC
> +
> +config CLK_RASPBERRYPI
> +	tristate "Raspberry Pi firmware based clock support"
> +	depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE)
> +	help
> +	  Enable common clock framework support for Raspberry Pi's firmware
> +	  dependent clocks
> diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
> index 002661d39128..eb7159099d82 100644
> --- a/drivers/clk/bcm/Makefile
> +++ b/drivers/clk/bcm/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm21664.o
>  obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
>  obj-$(CONFIG_ARCH_BCM2835)	+= clk-bcm2835.o
>  obj-$(CONFIG_ARCH_BCM2835)	+= clk-bcm2835-aux.o
> +obj-$(CONFIG_CLK_RASPBERRYPI)	+= clk-raspberrypi.o
>  obj-$(CONFIG_ARCH_BCM_53573)	+= clk-bcm53573-ilp.o
>  obj-$(CONFIG_CLK_BCM_CYGNUS)	+= clk-cygnus.o
>  obj-$(CONFIG_CLK_BCM_HR2)	+= clk-hr2.o

not your fault but you better rebase your next version on linux-next
because Florian's latest patches ("clk: bcm: Make BCM2835 clock drivers
selectable") collide with this patch.

Checkpatch gives the following output about this patch:

WARNING: 'harware' may be misspelled - perhaps 'hardware'?

#58: FILE: drivers/clk/bcm/clk-raspberrypi.c:5:
+ * Even though clk-bcm2835 provides an interface to the harware
registers for

ERROR: code indent should use tabs where possible
#197: FILE: drivers/clk/bcm/clk-raspberrypi.c:144:
+^I^I^I^IÂÂÂÂÂÂÂÂÂÂ struct clk_rate_request *req)$