Re: [PATCH v7 5/6] usb:cdns3 Add Cadence USB3 DRD Driver

From: Jun Li
Date: Fri Jun 14 2019 - 02:36:25 EST

Next message: Viresh Kumar: "Re: [RFC v2 02/11] OPP: Make dev_pm_opp_set_rate() with freq=0 as valid"
Previous message: Christoph Hellwig: "Re: [PATCH 09/22] memremap: lift the devmap_enable manipulation into devm_memremap_pages"
In reply to: Heikki Krogerus: "Re: [PATCH v7 5/6] usb:cdns3 Add Cadence USB3 DRD Driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Pawel Laszczak <pawell@xxxxxxxxxxx> ä2019å6æ5æåä äå6:07åéï
>
> This patch introduce new Cadence USBSS DRD driver to Linux kernel.
>
> The Cadence USBSS DRD Driver is a highly configurable IP Core which
> can be instantiated as Dual-Role Device (DRD), Peripheral Only and
> Host Only (XHCI)configurations.
>
> The current driver has been validated with FPGA platform. We have
> support for PCIe bus, which is used on FPGA prototyping.
>
> The host side of USBSS-DRD controller is compliant with XHCI
> specification, so it works with standard XHCI Linux driver.
>
> Signed-off-by: Pawel Laszczak <pawell@xxxxxxxxxxx>
> ---
> drivers/usb/Kconfig | 2 +
> drivers/usb/Makefile | 2 +
> drivers/usb/cdns3/Kconfig | 44 +
> drivers/usb/cdns3/Makefile | 14 +
> drivers/usb/cdns3/cdns3-pci-wrap.c | 157 ++
> drivers/usb/cdns3/core.c | 529 +++++++
> drivers/usb/cdns3/core.h | 121 ++
> drivers/usb/cdns3/debug.h | 173 +++
> drivers/usb/cdns3/debugfs.c | 173 +++
> drivers/usb/cdns3/drd.c | 379 +++++
> drivers/usb/cdns3/drd.h | 166 ++
> drivers/usb/cdns3/ep0.c | 915 +++++++++++
> drivers/usb/cdns3/gadget-export.h | 28 +
> drivers/usb/cdns3/gadget.c | 2290 ++++++++++++++++++++++++++++
> drivers/usb/cdns3/gadget.h | 1313 ++++++++++++++++
> drivers/usb/cdns3/host-export.h | 28 +
> drivers/usb/cdns3/host.c | 76 +
> drivers/usb/cdns3/trace.c | 23 +
> drivers/usb/cdns3/trace.h | 447 ++++++
> 19 files changed, 6880 insertions(+)
> create mode 100644 drivers/usb/cdns3/Kconfig
> create mode 100644 drivers/usb/cdns3/Makefile
> create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
> create mode 100644 drivers/usb/cdns3/core.c
> create mode 100644 drivers/usb/cdns3/core.h
> create mode 100644 drivers/usb/cdns3/debug.h
> create mode 100644 drivers/usb/cdns3/debugfs.c
> create mode 100644 drivers/usb/cdns3/drd.c
> create mode 100644 drivers/usb/cdns3/drd.h
> create mode 100644 drivers/usb/cdns3/ep0.c
> create mode 100644 drivers/usb/cdns3/gadget-export.h
> create mode 100644 drivers/usb/cdns3/gadget.c
> create mode 100644 drivers/usb/cdns3/gadget.h
> create mode 100644 drivers/usb/cdns3/host-export.h
> create mode 100644 drivers/usb/cdns3/host.c
> create mode 100644 drivers/usb/cdns3/trace.c
> create mode 100644 drivers/usb/cdns3/trace.h
>
> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
> index e4b27413f528..c2e78882f8c2 100644
> --- a/drivers/usb/Kconfig
> +++ b/drivers/usb/Kconfig
> @@ -113,6 +113,8 @@ source "drivers/usb/usbip/Kconfig"
>
> endif
>
> +source "drivers/usb/cdns3/Kconfig"
> +
> source "drivers/usb/mtu3/Kconfig"
>
> source "drivers/usb/musb/Kconfig"
> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
> index 7d1b8c82b208..ab125b966cac 100644
> --- a/drivers/usb/Makefile
> +++ b/drivers/usb/Makefile
> @@ -12,6 +12,8 @@ obj-$(CONFIG_USB_DWC3) += dwc3/
> obj-$(CONFIG_USB_DWC2) += dwc2/
> obj-$(CONFIG_USB_ISP1760) += isp1760/
>
> +obj-$(CONFIG_USB_CDNS3) += cdns3/
> +
> obj-$(CONFIG_USB_MON) += mon/
> obj-$(CONFIG_USB_MTU3) += mtu3/
>
> diff --git a/drivers/usb/cdns3/Kconfig b/drivers/usb/cdns3/Kconfig
> new file mode 100644
> index 000000000000..118ec91c4c70
> --- /dev/null
> +++ b/drivers/usb/cdns3/Kconfig
> @@ -0,0 +1,44 @@
> +config USB_CDNS3
> + tristate "Cadence USB3 Dual-Role Controller"
> + depends on USB_SUPPORT && (USB || USB_GADGET) && HAS_DMA
> + help
> + Say Y here if your system has a Cadence USB3 dual-role controller.
> + It supports: dual-role switch, Host-only, and Peripheral-only.
> +
> + If you choose to build this driver is a dynamically linked
> + as module, the module will be called cdns3.ko.
> +
> +if USB_CDNS3
> +
> +config USB_CDNS3_GADGET
> + bool "Cadence USB3 device controller"
> + depends on USB_GADGET
> + help
> + Say Y here to enable device controller functionality of the
> + Cadence USBSS-DEV driver.
> +
> + This controller supports FF, HS and SS mode. It doesn't support
> + LS and SSP mode.
> +
> +config USB_CDNS3_HOST
> + bool "Cadence USB3 host controller"
> + depends on USB_XHCI_HCD
> + help
> + Say Y here to enable host controller functionality of the
> + Cadence driver.
> +
> + Host controller is compliant with XHCI so it will use
> + standard XHCI driver.
> +
> +config USB_CDNS3_PCI_WRAP
> + tristate "Cadence USB3 support on PCIe-based platforms"
> + depends on USB_PCI && ACPI
> + default USB_CDNS3
> + help
> + If you're using the USBSS Core IP with a PCIe, please say
> + 'Y' or 'M' here.
> +
> + If you choose to build this driver as module it will
> + be dynamically linked and module will be called cdns3-pci.ko
> +
> +endif
> diff --git a/drivers/usb/cdns3/Makefile b/drivers/usb/cdns3/Makefile
> new file mode 100644
> index 000000000000..46c27b94b94b
> --- /dev/null
> +++ b/drivers/usb/cdns3/Makefile
> @@ -0,0 +1,14 @@
> +# SPDX-License-Identifier: GPL-2.0
> +# define_trace.h needs to know how to find our header
> +CFLAGS_trace.o := -I$(src)
> +
> +cdns3-y := core.o drd.o
> +
> +obj-$(CONFIG_USB_CDNS3) += cdns3.o
> +ifneq ($(CONFIG_DEBUG_FS),)
> + cdns3-y += debugfs.o
> +endif
> +
> +cdns3-$(CONFIG_USB_CDNS3_GADGET) += gadget.o ep0.o trace.o
> +cdns3-$(CONFIG_USB_CDNS3_HOST) += host.o
> +obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci-wrap.o
> diff --git a/drivers/usb/cdns3/cdns3-pci-wrap.c b/drivers/usb/cdns3/cdns3-pci-wrap.c
> new file mode 100644
> index 000000000000..65b61ea246b1
> --- /dev/null
> +++ b/drivers/usb/cdns3/cdns3-pci-wrap.c
> @@ -0,0 +1,157 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS PCI Glue driver
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/slab.h>
> +
> +struct cdns3_wrap {
> + struct platform_device *plat_dev;
> + struct pci_dev *hg_dev;
> + struct resource dev_res[6];
> +};
> +
> +#define RES_IRQ_HOST_ID 0
> +#define RES_IRQ_PERIPHERAL_ID 1
> +#define RES_IRQ_OTG_ID 2
> +#define RES_HOST_ID 3
> +#define RES_DEV_ID 4
> +#define RES_DRD_ID 5
> +
> +#define PCI_BAR_HOST 0
> +#define PCI_BAR_DEV 2
> +#define PCI_BAR_OTG 4
> +
> +#define PCI_DEV_FN_HOST_DEVICE 0
> +#define PCI_DEV_FN_OTG 1
> +
> +#define PCI_DRIVER_NAME "cdns3-pci-usbss"
> +#define PLAT_DRIVER_NAME "cdns-usb3"
> +
> +#define CDNS_VENDOR_ID 0x17cd
> +#define CDNS_DEVICE_ID 0x0100
> +
> +static int cdns3_pci_probe(struct pci_dev *pdev,
> + const struct pci_device_id *id)
> +{
> + struct platform_device_info plat_info;
> + struct cdns3_wrap *wrap;
> + struct resource *res;
> + int err;
> +
> + /*
> + * for GADGET/HOST PCI (devfn) function number is 0,
> + * for OTG PCI (devfn) function number is 1
> + */
> + if (!id || pdev->devfn != PCI_DEV_FN_HOST_DEVICE)
> + return -EINVAL;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", err);
> + return err;
> + }
> +
> + pci_set_master(pdev);
> + wrap = devm_kzalloc(&pdev->dev, sizeof(*wrap), GFP_KERNEL);
> + if (!wrap) {
> + pci_disable_device(pdev);
> + return -ENOMEM;
> + }
> +
> + /* function 0: host(BAR_0) + device(BAR_1) + otg(BAR_2)). */
> + dev_dbg(&pdev->dev, "Initialize Device resources\n");
> + res = wrap->dev_res;
> +
> + res[RES_DEV_ID].start = pci_resource_start(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].end = pci_resource_end(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].name = "dev";
> + res[RES_DEV_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-DEV physical base addr: %pa\n",
> + &res[RES_DEV_ID].start);
> +
> + res[RES_HOST_ID].start = pci_resource_start(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].end = pci_resource_end(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].name = "xhci";
> + res[RES_HOST_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-XHCI physical base addr: %pa\n",
> + &res[RES_HOST_ID].start);
> +
> + res[RES_DRD_ID].start = pci_resource_start(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].end = pci_resource_end(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].name = "otg";
> + res[RES_DRD_ID].flags = IORESOURCE_MEM;
> + dev_dbg(&pdev->dev, "USBSS-DRD physical base addr: %pa\n",
> + &res[RES_DRD_ID].start);
> +
> + /* Interrupt for XHCI */
> + wrap->dev_res[RES_IRQ_HOST_ID].start = pdev->irq;
> + wrap->dev_res[RES_IRQ_HOST_ID].name = "host";
> + wrap->dev_res[RES_IRQ_HOST_ID].flags = IORESOURCE_IRQ;
> +
> + /* Interrupt device. It's the same as for HOST. */
> + wrap->dev_res[RES_IRQ_PERIPHERAL_ID].start = pdev->irq;
> + wrap->dev_res[RES_IRQ_PERIPHERAL_ID].name = "peripheral";
> + wrap->dev_res[RES_IRQ_PERIPHERAL_ID].flags = IORESOURCE_IRQ;
> +
> + /* Interrupt for OTG/DRD. */
> + wrap->dev_res[RES_IRQ_OTG_ID].start = pdev->irq;
> + wrap->dev_res[RES_IRQ_OTG_ID].name = "otg";
> + wrap->dev_res[RES_IRQ_OTG_ID].flags = IORESOURCE_IRQ;
> +
> + /* set up platform device info */
> + memset(&plat_info, 0, sizeof(plat_info));
> + plat_info.parent = &pdev->dev;
> + plat_info.fwnode = pdev->dev.fwnode;
> + plat_info.name = PLAT_DRIVER_NAME;
> + plat_info.id = pdev->devfn;
> + plat_info.res = wrap->dev_res;
> + plat_info.num_res = ARRAY_SIZE(wrap->dev_res);
> + plat_info.dma_mask = pdev->dma_mask;
> +
> + /* register platform device */
> + wrap->plat_dev = platform_device_register_full(&plat_info);
> + if (IS_ERR(wrap->plat_dev)) {
> + pci_disable_device(pdev);
> + return PTR_ERR(wrap->plat_dev);
> + }
> +
> + pci_set_drvdata(pdev, wrap);
> +
> + return err;
> +}
> +
> +static void cdns3_pci_remove(struct pci_dev *pdev)
> +{
> + struct cdns3_wrap *wrap = (struct cdns3_wrap *)pci_get_drvdata(pdev);
> +
> + platform_device_unregister(wrap->plat_dev);
> +}
> +
> +static const struct pci_device_id cdns3_pci_ids[] = {
> + { PCI_DEVICE(CDNS_VENDOR_ID, CDNS_DEVICE_ID), },
> + { 0, }
> +};
> +
> +static struct pci_driver cdns3_pci_driver = {
> + .name = PCI_DRIVER_NAME,
> + .id_table = cdns3_pci_ids,
> + .probe = cdns3_pci_probe,
> + .remove = cdns3_pci_remove,
> +};
> +
> +module_pci_driver(cdns3_pci_driver);
> +MODULE_DEVICE_TABLE(pci, cdns3_pci_ids);
> +
> +MODULE_AUTHOR("Pawel Laszczak <pawell@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Cadence USBSS PCI wrapperr");
> diff --git a/drivers/usb/cdns3/core.c b/drivers/usb/cdns3/core.c
> new file mode 100644
> index 000000000000..daf146efbb35
> --- /dev/null
> +++ b/drivers/usb/cdns3/core.c
> @@ -0,0 +1,529 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver.
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + * Copyright (C) 2017-2018 NXP
> + * Copyright (C) 2019 Texas Instruments
> + *
> + * Author: Peter Chen <peter.chen@xxxxxxx>
> + * Pawel Laszczak <pawell@xxxxxxxxxxx>
> + * Roger Quadros <rogerq@xxxxxx>
> + */
> +
> +#include <linux/dma-mapping.h>
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/pm_runtime.h>
> +
> +#include "gadget.h"
> +#include "core.h"
> +#include "host-export.h"
> +#include "gadget-export.h"
> +#include "drd.h"
> +#include "debug.h"
> +
> +/**
> + * cdns3_handshake - spin reading until handshake completes or fails
> + * @ptr: address of device controller register to be read
> + * @mask: bits to look at in result of read
> + * @done: value of those bits when handshake succeeds
> + * @usec: timeout in microseconds
> + *
> + * Returns negative errno, or zero on success
> + *
> + * Success happens when the "mask" bits have the specified value (hardware
> + * handshake done). There are two failure modes: "usec" have passed (major
> + * hardware flakeout), or the register reads as all-ones (hardware removed).
> + */
> +int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec)
> +{
> + u32 result;
> +
> + do {
> + result = readl(ptr);
> + if (result == ~(u32)0) /* card removed */
> + return -ENODEV;
> +
> + result &= mask;
> + if (result == done)
> + return 0;
> +
> + udelay(1);
> + usec--;
> + } while (usec > 0);

readl_poll_timeout_atomic()

> +
> + return -ETIMEDOUT;
> +}
> +
> +static inline
> +struct cdns3_role_driver *cdns3_get_current_role_driver(struct cdns3 *cdns)
> +{
> + WARN_ON(cdns->role >= CDNS3_ROLE_END || !cdns->roles[cdns->role]);
> + return cdns->roles[cdns->role];
> +}
> +
> +static int cdns3_role_start(struct cdns3 *cdns, enum cdns3_roles role)
> +{
> + int ret;
> +
> + if (WARN_ON(role >= CDNS3_ROLE_END))
> + return 0;
> +
> + if (!cdns->roles[role])
> + return -ENXIO;
> +
> + if (cdns->roles[role]->state == CDNS3_ROLE_STATE_ACTIVE)
> + return 0;
> +
> + mutex_lock(&cdns->mutex);
> + cdns->role = role;
> + ret = cdns->roles[role]->start(cdns);
> + if (!ret)
> + cdns->roles[role]->state = CDNS3_ROLE_STATE_ACTIVE;
> + mutex_unlock(&cdns->mutex);
> + return ret;
> +}
> +
> +void cdns3_role_stop(struct cdns3 *cdns)
> +{
> + enum cdns3_roles role = cdns->role;
> +
> + if (role >= CDNS3_ROLE_END) {
> + WARN_ON(role > CDNS3_ROLE_END);
> + return;
> + }
> +
> + if (cdns->roles[role]->state == CDNS3_ROLE_STATE_INACTIVE)
> + return;
> +
> + mutex_lock(&cdns->mutex);
> + cdns->roles[role]->stop(cdns);
> + cdns->roles[role]->state = CDNS3_ROLE_STATE_INACTIVE;
> + mutex_unlock(&cdns->mutex);
> +}
> +
> +static void cdns3_exit_roles(struct cdns3 *cdns)
> +{
> + cdns3_role_stop(cdns);
> + cdns3_drd_exit(cdns);
> +}
> +
> +enum cdns3_roles cdsn3_get_real_role(struct cdns3 *cdns);
> +
> +static int cdns3_idle_role_start(struct cdns3 *cnds)
> +{ /* Hold PHY in RESET */
> + return 0;
> +}
> +
> +static void cdns3_idle_role_stop(struct cdns3 *cnds)
> +{
> + /* Program Lane swap and bring PHY out of RESET */
> +}
> +
> +static int cdns3_idle_init(struct cdns3 *cdns)
> +{
> + struct cdns3_role_driver *rdrv;
> +
> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
> + if (!rdrv)
> + return -ENOMEM;
> +
> + rdrv->start = cdns3_idle_role_start;
> + rdrv->stop = cdns3_idle_role_stop;
> + rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> + rdrv->suspend = NULL;
> + rdrv->resume = NULL;
> + rdrv->name = "idle";
> +
> + cdns->roles[CDNS3_ROLE_IDLE] = rdrv;
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_core_init_role - initialize role of operation
> + * @cdns: Pointer to cdns3 structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_core_init_role(struct cdns3 *cdns)
> +{
> + struct device *dev = cdns->dev;
> + enum usb_dr_mode best_dr_mode;
> + enum usb_dr_mode dr_mode;
> + int ret = 0;
> +
> + dr_mode = usb_get_dr_mode(dev);
> + cdns->role = CDNS3_ROLE_END;
> +
> + /*
> + * If driver can't read mode by means of usb_get_dr_mode function then
> + * chooses mode according with Kernel configuration. This setting

Only consider kernel configuration in case of can't read from usb_get_dr_mode?

> + * can be restricted later depending on strap pin configuration.

So I think you'd better have one central place to get dr mode which consider:
- usb_get_dr_mode
- kernel config
- strap pin

> + */
> + if (dr_mode == USB_DR_MODE_UNKNOWN) {
> + if (IS_ENABLED(CONFIG_USB_CDNS3_HOST) &&
> + IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
> + dr_mode = USB_DR_MODE_OTG;
> + else if (IS_ENABLED(CONFIG_USB_CDNS3_HOST))
> + dr_mode = USB_DR_MODE_HOST;
> + else if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET))
> + dr_mode = USB_DR_MODE_PERIPHERAL;
> + }
> +
> + /*
> + * At this point cdns->dr_mode contains strap configuration.
> + * Driver try update this setting considering kernel configuration
> + */
> + best_dr_mode = cdns->dr_mode;
> +
> + ret = cdns3_idle_init(cdns);
> + if (ret)
> + return ret;
> +
> + if (dr_mode == USB_DR_MODE_OTG) {
> + best_dr_mode = cdns->dr_mode;
> + } else if (cdns->dr_mode == USB_DR_MODE_OTG) {
> + best_dr_mode = dr_mode;
> + } else if (cdns->dr_mode != dr_mode) {
> + dev_err(dev, "Incorrect DRD configuration\n");
> + return -EINVAL;
> + }
> +
> + dr_mode = best_dr_mode;
> +
> + if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_HOST) {
> + ret = cdns3_host_init(cdns);
> + if (ret) {
> + dev_err(dev, "Host initialization failed with %d\n",
> + ret);
> + goto err;
> + }
> + }
> +
> + if (dr_mode == USB_DR_MODE_OTG || dr_mode == USB_DR_MODE_PERIPHERAL) {
> + ret = cdns3_gadget_init(cdns);
> + if (ret) {
> + dev_err(dev, "Device initialization failed with %d\n",
> + ret);
> + goto err;
> + }
> + }
> +
> + cdns->desired_dr_mode = dr_mode;
> + cdns->dr_mode = dr_mode;
> +
> + /*
> + * desired_dr_mode might have changed so we need to update
> + * the controller configuration"?
> + */
> + ret = cdns3_drd_update_mode(cdns);
> + if (ret)
> + goto err;
> +
> + cdns->role = cdsn3_get_real_role(cdns);
> +
> + ret = cdns3_role_start(cdns, cdns->role);
> + if (ret) {
> + dev_err(dev, "can't start %s role\n",
> + cdns3_get_current_role_driver(cdns)->name);
> + goto err;
> + }
> +
> + return ret;
> +err:
> + cdns3_exit_roles(cdns);
> + return ret;
> +}
> +
> +/**
> + * cdsn3_get_real_role - get real role of controller based on hardware settings.
> + * @cdns: Pointer to cdns3 structure
> + *
> + * Returns role
> + */
> +enum cdns3_roles cdsn3_get_real_role(struct cdns3 *cdns)
> +{
> + enum cdns3_roles role;
> + int id, vbus;
> +
> + if (cdns->current_dr_mode != USB_DR_MODE_OTG)
> + goto not_otg;
> +
> + id = cdns3_get_id(cdns);
> + vbus = cdns3_get_vbus(cdns);
> +
> + /*
> + * Role change state machine
> + * Inputs: ID, VBUS
> + * Previous state: cdns->role
> + * Next state: role
> + */
> + role = cdns->role;
> +
> + switch (role) {
> + case CDNS3_ROLE_IDLE: /* from IDLE, we can change to HOST or GADGET */
> + if (!id)
> + role = CDNS3_ROLE_HOST;
> + else if (vbus)
> + role = CDNS3_ROLE_GADGET;
> + break;
> + case CDNS3_ROLE_HOST: /* from HOST, we can only change to IDLE */
> + if (id)
> + role = CDNS3_ROLE_IDLE;
> + break;
> + case CDNS3_ROLE_GADGET: /* from GADGET, we can only change to IDLE */
> + if (!vbus)
> + role = CDNS3_ROLE_IDLE;
> + break;
> + case CDNS3_ROLE_END: /* only at initialization, move to IDLE */
> + role = CDNS3_ROLE_IDLE;
> + break;
> + }
> +
> + dev_info(cdns->dev, "role %d -> %d\n", cdns->role, role);
> +
> + return role;
> +
> +not_otg:
> + if (cdns3_is_host(cdns))
> + role = CDNS3_ROLE_HOST;
> + if (cdns3_is_device(cdns))
> + role = CDNS3_ROLE_GADGET;
> +
> + return role;
> +}
> +
> +/**
> + * cdns3_role_switch - work queue handler for role switch
> + *
> + * @work: work queue item structure
> + *
> + * Handles below events:
> + * - Role switch for dual-role devices
> + * - CDNS3_ROLE_GADGET <--> CDNS3_ROLE_END for peripheral-only devices
> + */
> +static void cdns3_role_switch(struct work_struct *work)
> +{
> + enum cdns3_roles role = CDNS3_ROLE_END;
> + struct cdns3_role_driver *role_drv;
> + enum cdns3_roles current_role;
> + struct cdns3 *cdns;
> + int ret = 0;
> +
> + cdns = container_of(work, struct cdns3, role_switch_wq);
> +
> + pm_runtime_get_sync(cdns->dev);
> +
> + role = cdsn3_get_real_role(cdns);
> +
> + role_drv = cdns3_get_current_role_driver(cdns);
> +
> + /* Disable current role if requested from debugfs */
> + if (cdns->debug_disable && role_drv->state == CDNS3_ROLE_STATE_ACTIVE) {

seems this "disable" file is only for debug purpose, need keep it in
formal patch?

> + cdns3_role_stop(cdns);
> + goto exit;
> + }
> +
> + /* Do nothing if nothing changed */
> + if (cdns->role == role && role_drv->state == CDNS3_ROLE_STATE_ACTIVE)
> + goto exit;
> +
> + cdns3_role_stop(cdns);
> +
> + role = cdsn3_get_real_role(cdns);
> +
> + current_role = cdns->role;
> + dev_dbg(cdns->dev, "Switching role");
> +
> + ret = cdns3_role_start(cdns, role);
> + if (ret) {
> + /* Back to current role */
> + dev_err(cdns->dev, "set %d has failed, back to %d\n",
> + role, current_role);
> + ret = cdns3_role_start(cdns, current_role);
> + if (ret)
> + dev_err(cdns->dev, "back to %d failed too\n",
> + current_role);
> + }
> +exit:
> + pm_runtime_put_sync(cdns->dev);
> +}
> +
> +/**
> + * cdns3_probe - probe for cdns3 core device
> + * @pdev: Pointer to cdns3 core platform device
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + struct cdns3 *cdns;
> + void __iomem *regs;
> + int ret;
> +
> + ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
> + if (ret) {
> + dev_err(dev, "error setting dma mask: %d\n", ret);
> + return -ENODEV;
> + }
> +
> + cdns = devm_kzalloc(dev, sizeof(*cdns), GFP_KERNEL);
> + if (!cdns)
> + return -ENOMEM;
> +
> + cdns->dev = dev;
> +
> + platform_set_drvdata(pdev, cdns);
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "host");
> + if (!res) {
> + dev_err(dev, "missing host IRQ\n");
> + return -ENODEV;
> + }
> +
> + cdns->xhci_res[0] = *res;
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "xhci");
> + if (!res) {
> + dev_err(dev, "couldn't get xhci resource\n");
> + return -ENXIO;
> + }
> +
> + cdns->xhci_res[1] = *res;
> +
> + cdns->dev_irq = platform_get_irq_byname(pdev, "peripheral");
> + if (cdns->dev_irq == -EPROBE_DEFER)
> + return cdns->dev_irq;
> +
> + if (cdns->dev_irq < 0)
> + dev_err(dev, "couldn't get peripheral irq\n");
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dev");
> + regs = devm_ioremap_resource(dev, res);
> + if (IS_ERR(regs)) {
> + dev_err(dev, "couldn't iomap dev resource\n");
> + return PTR_ERR(regs);
> + }
> + cdns->dev_regs = regs;
> +
> + cdns->otg_irq = platform_get_irq_byname(pdev, "otg");
> + if (cdns->otg_irq == -EPROBE_DEFER)
> + return cdns->otg_irq;
> +
> + if (cdns->otg_irq < 0) {
> + dev_err(dev, "couldn't get otg irq\n");
> + return cdns->otg_irq;
> + }
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "otg");
> + if (!res) {
> + dev_err(dev, "couldn't get otg resource\n");
> + return -ENXIO;
> + }
> +
> + cdns->otg_res = *res;
> +
> + mutex_init(&cdns->mutex);
> +
> + cdns->phy = devm_phy_optional_get(dev, "cdns3,usbphy");
> + if (IS_ERR(cdns->phy))
> + return PTR_ERR(cdns->phy);
> +
> + phy_init(cdns->phy);
> + ret = phy_init(cdns->phy);
> + if (ret) {
> + dev_err(dev, "phy_init error\n");
> + return ret;
> + }
> +
> + ret = phy_power_on(cdns->phy);
> + if (ret) {
> + dev_err(dev, "phy_power_on error\n");
> + phy_exit(cdns->phy);
> + return ret;
> + }
> +
> + INIT_WORK(&cdns->role_switch_wq, cdns3_role_switch);
> +
> + ret = cdns3_drd_init(cdns);
> + if (ret)
> + goto err;
> +
> + ret = cdns3_core_init_role(cdns);
> + if (ret)
> + goto err;
> +
> + cdns3_debugfs_init(cdns);
> + device_set_wakeup_capable(dev, true);
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> +
> + /*
> + * The controller needs less time between bus and controller suspend,
> + * and we also needs a small delay to avoid frequently entering low
> + * power mode.
> + */
> + pm_runtime_set_autosuspend_delay(dev, 20);
> + pm_runtime_mark_last_busy(dev);
> + pm_runtime_use_autosuspend(dev);
> + dev_dbg(dev, "Cadence USB3 core: probe succeed\n");
> +
> + return 0;
> +
> +err:
> + phy_power_off(cdns->phy);
> + phy_exit(cdns->phy);
> + return ret;
> +}
> +
> +/**
> + * cdns3_remove - unbind drd driver and clean up
> + * @pdev: Pointer to Linux platform device
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_remove(struct platform_device *pdev)
> +{
> + struct cdns3 *cdns = platform_get_drvdata(pdev);
> +
> + pm_runtime_get_sync(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
> + pm_runtime_put_noidle(&pdev->dev);
> + cdns3_debugfs_exit(cdns);
> + cdns3_exit_roles(cdns);
> + phy_power_off(cdns->phy);
> + phy_exit(cdns->phy);
> + return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id of_cdns3_match[] = {
> + { .compatible = "cdns,usb3-1.0.0" },
> + { .compatible = "cdns,usb3-1.0.1" },

Can't this version infor be read out from register?

> + { },
> +};
> +MODULE_DEVICE_TABLE(of, of_cdns3_match);
> +#endif
> +
> +static struct platform_driver cdns3_driver = {
> + .probe = cdns3_probe,
> + .remove = cdns3_remove,
> + .driver = {
> + .name = "cdns-usb3",
> + .of_match_table = of_match_ptr(of_cdns3_match),
> + },
> +};
> +
> +module_platform_driver(cdns3_driver);
> +
> +MODULE_ALIAS("platform:cdns3");
> +MODULE_AUTHOR("Pawel Laszczak <pawell@xxxxxxxxxxx>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Cadence USB3 DRD Controller Driver");
> diff --git a/drivers/usb/cdns3/core.h b/drivers/usb/cdns3/core.h
> new file mode 100644
> index 000000000000..83fc5f6f60c5
> --- /dev/null
> +++ b/drivers/usb/cdns3/core.h
> @@ -0,0 +1,121 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Header File.
> + *
> + * Copyright (C) 2017-2018 NXP
> + * Copyright (C) 2018-2019 Cadence.
> + *
> + * Authors: Peter Chen <peter.chen@xxxxxxx>
> + * Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +#include <linux/usb/otg.h>
> +
> +#ifndef __LINUX_CDNS3_CORE_H
> +#define __LINUX_CDNS3_CORE_H
> +
> +struct cdns3;
> +enum cdns3_roles {
> + CDNS3_ROLE_IDLE = 0,
> + CDNS3_ROLE_HOST,
> + CDNS3_ROLE_GADGET,
> + CDNS3_ROLE_END,
> +};
> +
> +/**
> + * struct cdns3_role_driver - host/gadget role driver
> + * @start: start this role
> + * @stop: stop this role
> + * @suspend: suspend callback for this role
> + * @resume: resume callback for this role
> + * @irq: irq handler for this role
> + * @name: role name string (host/gadget)
> + * @state: current state
> + */
> +struct cdns3_role_driver {
> + int (*start)(struct cdns3 *cdns);
> + void (*stop)(struct cdns3 *cdns);
> + int (*suspend)(struct cdns3 *cdns, bool do_wakeup);
> + int (*resume)(struct cdns3 *cdns, bool hibernated);
> + const char *name;
> +#define CDNS3_ROLE_STATE_INACTIVE 0
> +#define CDNS3_ROLE_STATE_ACTIVE 1
> + int state;
> +};
> +
> +#define CDNS3_XHCI_RESOURCES_NUM 2
> +/**
> + * struct cdns3 - Representation of Cadence USB3 DRD controller.
> + * @dev: pointer to Cadence device struct
> + * @xhci_regs: pointer to base of xhci registers
> + * @xhci_res: the resource for xhci
> + * @dev_regs: pointer to base of dev registers
> + * @otg_res: the resource for otg
> + * @otg_v0_regs: pointer to base of v0 otg registers
> + * @otg_v1_regs: pointer to base of v1 otg registers
> + * @otg_regs: pointer to base of otg registers
> + * @otg_irq: irq number for otg controller
> + * @dev_irq: irq number for device controller
> + * @roles: array of supported roles for this controller
> + * @role: current role
> + * @host_dev: the child host device pointer for cdns3 core
> + * @gadget_dev: the child gadget device pointer for cdns3 core
> + * @usb: phy for this controller
> + * @role_switch_wq: work queue item for role switch
> + * @in_lpm: the controller in low power mode
> + * @wakeup_int: the wakeup interrupt
> + * @mutex: the mutex for concurrent code at driver
> + * @dr_mode: supported mode of operation it can be only Host, only Device
> + * or OTG mode that allow to switch between Device and Host mode.
> + * This field based on firmware setting, kernel configuration
> + * and hardware configuration.
> + * @current_dr_mode: current mode of operation when in dual-role mode
> + * @desired_dr_mode: desired mode of operation when in dual-role mode.
> + * This value can be changed during runtime.
> + * Available options depends on dr_mode:
> + * dr_mode | desired_dr_mode and current_dr_mode
> + * ----------------------------------------------------------------
> + * USB_DR_MODE_HOST | only USB_DR_MODE_HOST
> + * USB_DR_MODE_PERIPHERAL | only USB_DR_MODE_PERIPHERAL
> + * USB_DR_MODE_OTG | USB_DR_MODE_OTG or USB_DR_MODE_HOST or
> + * | USB_DR_MODE_PERIPHERAL
> + * Desired_dr_role can be changed by means of debugfs.
> + * @root: debugfs root folder pointer
> + * @debug_disable:
> + */
> +struct cdns3 {
> + struct device *dev;
> + void __iomem *xhci_regs;
> + struct resource xhci_res[CDNS3_XHCI_RESOURCES_NUM];
> + struct cdns3_usb_regs __iomem *dev_regs;
> +
> + struct resource otg_res;
> + struct cdns3_otg_legacy_regs *otg_v0_regs;
> + struct cdns3_otg_regs *otg_v1_regs;
> + struct cdns3_otg_common_regs *otg_regs;
> +#define CDNS3_CONTROLLER_V0 0
> +#define CDNS3_CONTROLLER_V1 1
> + u32 version;
> +
> + int otg_irq;
> + int dev_irq;
> + struct cdns3_role_driver *roles[CDNS3_ROLE_END];
> + enum cdns3_roles role;
> + struct platform_device *host_dev;
> + struct cdns3_device *gadget_dev;
> + struct phy *phy;
> + struct work_struct role_switch_wq;
> + int in_lpm:1;
> + int wakeup_int:1;
> + /* mutext used in workqueue*/
> + struct mutex mutex;
> + enum usb_dr_mode dr_mode;
> + enum usb_dr_mode current_dr_mode;
> + enum usb_dr_mode desired_dr_mode;
> + struct dentry *root;
> + int debug_disable:1;
> +};
> +
> +void cdns3_role_stop(struct cdns3 *cdns);
> +int cdns3_handshake(void __iomem *ptr, u32 mask, u32 done, int usec);
> +
> +#endif /* __LINUX_CDNS3_CORE_H */
> diff --git a/drivers/usb/cdns3/debug.h b/drivers/usb/cdns3/debug.h
> new file mode 100644
> index 000000000000..65c3d8a6cd62
> --- /dev/null
> +++ b/drivers/usb/cdns3/debug.h
> @@ -0,0 +1,173 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver.
> + * Debug header file.
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +#ifndef __LINUX_CDNS3_DEBUG
> +#define __LINUX_CDNS3_DEBUG
> +
> +#include "core.h"
> +
> +static inline char *cdns3_decode_usb_irq(char *str,
> + enum usb_device_speed speed,
> + u32 usb_ists)
> +{
> + int ret;
> +
> + ret = sprintf(str, "IRQ %08x = ", usb_ists);
> +
> + if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
> + ret += sprintf(str + ret, "Connection %s\n",
> + usb_speed_string(speed));
> + }
> + if (usb_ists & USB_ISTS_DIS2I || usb_ists & USB_ISTS_DISI)
> + ret += sprintf(str + ret, "Disconnection ");
> + if (usb_ists & USB_ISTS_L2ENTI)
> + ret += sprintf(str + ret, "suspended ");
> + if (usb_ists & USB_ISTS_L1ENTI)
> + ret += sprintf(str + ret, "L1 enter ");
> + if (usb_ists & USB_ISTS_L1EXTI)
> + ret += sprintf(str + ret, "L1 exit ");
> + if (usb_ists & USB_ISTS_L2ENTI)
> + ret += sprintf(str + ret, "L2 enter ");
> + if (usb_ists & USB_ISTS_L2EXTI)
> + ret += sprintf(str + ret, "L2 exit ");
> + if (usb_ists & USB_ISTS_U3EXTI)
> + ret += sprintf(str + ret, "U3 exit ");
> + if (usb_ists & USB_ISTS_UWRESI)
> + ret += sprintf(str + ret, "Warm Reset ");
> + if (usb_ists & USB_ISTS_UHRESI)
> + ret += sprintf(str + ret, "Hot Reset ");
> + if (usb_ists & USB_ISTS_U2RESI)
> + ret += sprintf(str + ret, "Reset");
> +
> + return str;
> +}
> +
> +static inline char *cdns3_decode_ep_irq(char *str,
> + u32 ep_sts,
> + const char *ep_name)
> +{
> + int ret;
> +
> + ret = sprintf(str, "IRQ for %s: %08x ", ep_name, ep_sts);
> +
> + if (ep_sts & EP_STS_SETUP)
> + ret += sprintf(str + ret, "SETUP ");
> + if (ep_sts & EP_STS_IOC)
> + ret += sprintf(str + ret, "IOC ");
> + if (ep_sts & EP_STS_ISP)
> + ret += sprintf(str + ret, "ISP ");
> + if (ep_sts & EP_STS_DESCMIS)
> + ret += sprintf(str + ret, "DESCMIS ");
> + if (ep_sts & EP_STS_STREAMR)
> + ret += sprintf(str + ret, "STREAMR ");
> + if (ep_sts & EP_STS_MD_EXIT)
> + ret += sprintf(str + ret, "MD_EXIT ");
> + if (ep_sts & EP_STS_TRBERR)
> + ret += sprintf(str + ret, "TRBERR ");
> + if (ep_sts & EP_STS_NRDY)
> + ret += sprintf(str + ret, "NRDY ");
> + if (ep_sts & EP_STS_PRIME)
> + ret += sprintf(str + ret, "PRIME ");
> + if (ep_sts & EP_STS_SIDERR)
> + ret += sprintf(str + ret, "SIDERRT ");
> + if (ep_sts & EP_STS_OUTSMM)
> + ret += sprintf(str + ret, "OUTSMM ");
> + if (ep_sts & EP_STS_ISOERR)
> + ret += sprintf(str + ret, "ISOERR ");
> + if (ep_sts & EP_STS_IOT)
> + ret += sprintf(str + ret, "IOT ");
> +
> + return str;
> +}
> +
> +static inline char *cdns3_decode_epx_irq(char *str,
> + char *ep_name,
> + u32 ep_sts)
> +{
> + return cdns3_decode_ep_irq(str, ep_sts, ep_name);
> +}
> +
> +static inline char *cdns3_decode_ep0_irq(char *str,
> + int dir,
> + u32 ep_sts)
> +{
> + return cdns3_decode_ep_irq(str, ep_sts,
> + dir ? "ep0IN" : "ep0OUT");
> +}
> +
> +/**
> + * Debug a transfer ring.
> + *
> + * Prints out all TRBs in the endpoint ring, even those after the Link TRB.
> + *.
> + */
> +static inline char *cdns3_dbg_ring(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *ring, char *str)
> +{
> + dma_addr_t addr = priv_ep->trb_pool_dma;
> + struct cdns3_trb *trb;
> + int trb_per_sector;
> + int ret = 0;
> + int i;
> +
> + trb_per_sector = GET_TRBS_PER_SEGMENT(priv_ep->type);
> +
> + trb = &priv_ep->trb_pool[priv_ep->dequeue];
> + ret += sprintf(str + ret, "\n\t\tRing contents for %s:", priv_ep->name);
> +
> + ret += sprintf(str + ret,
> + "\n\t\tRing deq index: %d, trb: %p (virt), 0x%llx (dma)\n",
> + priv_ep->dequeue, trb,
> + (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
> +
> + trb = &priv_ep->trb_pool[priv_ep->enqueue];
> + ret += sprintf(str + ret,
> + "\t\tRing enq index: %d, trb: %p (virt), 0x%llx (dma)\n",
> + priv_ep->enqueue, trb,
> + (unsigned long long)cdns3_trb_virt_to_dma(priv_ep, trb));
> +
> + ret += sprintf(str + ret,
> + "\t\tfree trbs: %d, CCS=%d, PCS=%d\n",
> + priv_ep->free_trbs, priv_ep->ccs, priv_ep->pcs);
> +
> + if (trb_per_sector > TRBS_PER_SEGMENT)
> + trb_per_sector = TRBS_PER_SEGMENT;
> +
> + if (trb_per_sector > TRBS_PER_SEGMENT) {
> + sprintf(str + ret, "\t\tTo big transfer ring %d\n",
> + trb_per_sector);
> + return str;
> + }
> +
> + for (i = 0; i < trb_per_sector; ++i) {
> + trb = &ring[i];
> + ret += sprintf(str + ret,
> + "\t\t@%pad %08x %08x %08x\n", &addr,
> + le32_to_cpu(trb->buffer),
> + le32_to_cpu(trb->length),
> + le32_to_cpu(trb->control));
> + addr += sizeof(*trb);
> + }
> +
> + return str;
> +}
> +
> +void cdns3_dbg(struct cdns3_device *priv_dev, const char *fmt, ...);
> +
> +#ifdef CONFIG_DEBUG_FS
> +void cdns3_debugfs_init(struct cdns3 *cdns);
> +void cdns3_debugfs_exit(struct cdns3 *cdns);
> +#else
> +void cdns3_debugfs_init(struct cdns3 *cdns);
> +{ }
> +void cdns3_debugfs_exit(struct cdns3 *cdns);
> +{ }
> +#endif
> +
> +#endif /*__LINUX_CDNS3_DEBUG*/
> diff --git a/drivers/usb/cdns3/debugfs.c b/drivers/usb/cdns3/debugfs.c
> new file mode 100644
> index 000000000000..dfcbeb5e14f8
> --- /dev/null
> +++ b/drivers/usb/cdns3/debugfs.c
> @@ -0,0 +1,173 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Controller DebugFS filer.
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +
> +#include <linux/types.h>
> +#include <linux/debugfs.h>
> +#include <linux/seq_file.h>
> +#include <linux/uaccess.h>
> +
> +#include "core.h"
> +#include "gadget.h"
> +#include "drd.h"
> +
> +static int cdns3_mode_show(struct seq_file *s, void *unused)
> +{
> + struct cdns3 *cdns = s->private;
> +
> + switch (cdns->current_dr_mode) {
> + case USB_DR_MODE_HOST:
> + seq_puts(s, "host\n");
> + break;
> + case USB_DR_MODE_PERIPHERAL:
> + seq_puts(s, "device\n");
> + break;
> + case USB_DR_MODE_OTG:
> + seq_puts(s, "otg\n");
> + break;
> + default:
> + seq_puts(s, "UNKNOWN mode\n");
> + }
> +
> + return 0;
> +}
> +
> +static int cdns3_mode_open(struct inode *inode, struct file *file)
> +{
> + return single_open(file, cdns3_mode_show, inode->i_private);
> +}
> +
> +static ssize_t cdns3_mode_write(struct file *file,
> + const char __user *ubuf,
> + size_t count, loff_t *ppos)
> +{
> + struct seq_file *s = file->private_data;
> + struct cdns3 *cdns = s->private;
> + u32 mode = USB_DR_MODE_UNKNOWN;
> + char buf[32];
> + int ret = 0;
> +
> + if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
> + return -EFAULT;
> +
> + if (cdns->debug_disable) {
> + dev_err(cdns->dev,
> + "Mode can't be changed when disable is set\n");
> + return -EFAULT;
> + }
> +
> + if (!strncmp(buf, "host", 4)) {
> + if (cdns->dr_mode == USB_DR_MODE_HOST ||
> + cdns->dr_mode == USB_DR_MODE_OTG) {
> + mode = USB_DR_MODE_HOST;
> + }
> + }
> +
> + if (!strncmp(buf, "device", 6))
> + if (cdns->dr_mode == USB_DR_MODE_PERIPHERAL ||
> + cdns->dr_mode == USB_DR_MODE_OTG)
> + mode = USB_DR_MODE_PERIPHERAL;
> +
> + if (!strncmp(buf, "otg", 3) && cdns->dr_mode == USB_DR_MODE_OTG)
> + mode = USB_DR_MODE_OTG;
> +
> + if (mode == USB_DR_MODE_UNKNOWN) {
> + dev_err(cdns->dev, "Failed: incorrect mode setting\n");
> + return -EFAULT;
> + }
> +
> + if (cdns->current_dr_mode != mode) {
> + cdns->desired_dr_mode = mode;
> + cdns3_role_stop(cdns);
> + ret = cdns3_drd_update_mode(cdns);
> + if (ret)
> + return ret;
> +
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> + }
> +
> + return count;
> +}
> +
> +static const struct file_operations cdns3_mode_fops = {
> + .open = cdns3_mode_open,
> + .write = cdns3_mode_write,
> + .read = seq_read,
> + .llseek = seq_lseek,
> + .release = single_release,
> +};
> +
> +static int cdns3_disable_show(struct seq_file *s, void *unused)
> +{
> + struct cdns3 *cdns = s->private;
> +
> + if (!cdns->debug_disable)
> + seq_puts(s, "0\n");
> + else
> + seq_puts(s, "1\n");
> +
> + return 0;
> +}
> +
> +static ssize_t cdns3_disable_write(struct file *file,
> + const char __user *ubuf,
> + size_t count, loff_t *ppos)
> +{
> + struct seq_file *s = file->private_data;
> + struct cdns3 *cdns = s->private;
> + bool disable;
> + char buf[16];
> +
> + if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
> + return -EFAULT;
> +
> + if (kstrtobool(buf, &disable)) {
> + dev_err(cdns->dev, "wrong setting\n");
> + return -EINVAL;
> + }
> +
> + if (disable != cdns->debug_disable) {
> + cdns->debug_disable = disable;
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> + }
> +
> + return count;
> +}
> +
> +static int cdns3_disable_open(struct inode *inode, struct file *file)
> +{
> + return single_open(file, cdns3_disable_show, inode->i_private);
> +}
> +
> +static const struct file_operations cdns3_disable_fops = {
> + .open = cdns3_disable_open,
> + .write = cdns3_disable_write,
> + .read = seq_read,
> + .llseek = seq_lseek,
> + .release = single_release,
> +};
> +
> +void cdns3_debugfs_init(struct cdns3 *cdns)
> +{
> + struct dentry *root;
> +
> + root = debugfs_create_dir(dev_name(cdns->dev), NULL);
> + cdns->root = root;
> + if (IS_ENABLED(CONFIG_USB_CDNS3_GADGET) &&
> + IS_ENABLED(CONFIG_USB_CDNS3_HOST))
> + debugfs_create_file("mode", 0644, root, cdns,
> + &cdns3_mode_fops);
> +
> + debugfs_create_file("disable", 0644, root, cdns,
> + &cdns3_disable_fops);
> +}
> +
> +void cdns3_debugfs_exit(struct cdns3 *cdns)
> +{
> + debugfs_remove_recursive(cdns->root);
> +}
> diff --git a/drivers/usb/cdns3/drd.c b/drivers/usb/cdns3/drd.c
> new file mode 100644
> index 000000000000..2daef0746ddd
> --- /dev/null
> +++ b/drivers/usb/cdns3/drd.c
> @@ -0,0 +1,379 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver.
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + * Copyright (C) 2019 Texas Instruments
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + * Roger Quadros <rogerq@xxxxxx>
> + *
> + *
> + */
> +#include <linux/kernel.h>
> +#include <linux/interrupt.h>
> +#include <linux/delay.h>
> +#include <linux/usb/otg.h>
> +
> +#include "gadget.h"
> +#include "drd.h"
> +#include "core.h"
> +
> +/**
> + * cdns3_set_mode - change mode of OTG Core
> + * @cdns: pointer to context structure
> + * @mode: selected mode from cdns_role
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +int cdns3_set_mode(struct cdns3 *cdns, enum usb_dr_mode mode)
> +{
> + int ret = 0;
> + u32 reg;
> +
> + cdns->current_dr_mode = mode;
> +
> + switch (mode) {
> + case USB_DR_MODE_PERIPHERAL:
> + break;
> + case USB_DR_MODE_HOST:
> + break;
> + case USB_DR_MODE_OTG:
> + dev_dbg(cdns->dev, "Set controller to OTG mode\n");
> + if (cdns->version == CDNS3_CONTROLLER_V1) {
> + reg = readl(&cdns->otg_v1_regs->override);
> + reg |= OVERRIDE_IDPULLUP;
> + writel(reg, &cdns->otg_v1_regs->override);
> + } else {
> + reg = readl(&cdns->otg_v0_regs->ctrl1);
> + reg |= OVERRIDE_IDPULLUP_V0;
> + writel(reg, &cdns->otg_v0_regs->ctrl1);
> + }
> +
> + /*
> + * Hardware specification says: "ID_VALUE must be valid within
> + * 50ms after idpullup is set to '1" so driver must wait
> + * 50ms before reading this pin.
> + */
> + usleep_range(50000, 60000);
> + break;
> + default:
> + cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
> + dev_err(cdns->dev, "Unsupported mode of operation %d\n", mode);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +int cdns3_get_id(struct cdns3 *cdns)
> +{
> + int id;
> +
> + id = readl(&cdns->otg_regs->sts) & OTGSTS_ID_VALUE;
> + dev_dbg(cdns->dev, "OTG ID: %d", id);
> +
> + return id;
> +}
> +
> +int cdns3_get_vbus(struct cdns3 *cdns)
> +{
> + int vbus;
> +
> + vbus = !!(readl(&cdns->otg_regs->sts) & OTGSTS_VBUS_VALID);
> + dev_dbg(cdns->dev, "OTG VBUS: %d", vbus);
> + return vbus;
> +}
> +
> +int cdns3_is_host(struct cdns3 *cdns)
> +{
> + if (cdns->current_dr_mode == USB_DR_MODE_HOST)
> + return 1;
> + else if (!cdns3_get_id(cdns))
> + return 1;
> +
> + return 0;
> +}
> +
> +int cdns3_is_device(struct cdns3 *cdns)
> +{
> + if (cdns->current_dr_mode == USB_DR_MODE_PERIPHERAL)
> + return 1;
> + else if (cdns->current_dr_mode == USB_DR_MODE_OTG)
> + if (cdns3_get_id(cdns))
> + return 1;
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_otg_disable_irq - Disable all OTG interrupts
> + * @cdns: Pointer to controller context structure
> + */
> +static void cdns3_otg_disable_irq(struct cdns3 *cdns)
> +{
> + writel(0, &cdns->otg_regs->ien);
> +}
> +
> +/**
> + * cdns3_otg_enable_irq - enable id and sess_valid interrupts
> + * @cdns: Pointer to controller context structure
> + */
> +static void cdns3_otg_enable_irq(struct cdns3 *cdns)
> +{
> + writel(OTGIEN_ID_CHANGE_INT | OTGIEN_VBUSVALID_RISE_INT |
> + OTGIEN_VBUSVALID_FALL_INT, &cdns->otg_regs->ien);
> +}
> +
> +/**
> + * cdns3_drd_switch_host - start/stop host
> + * @cdns: Pointer to controller context structure
> + * @on: 1 for start, 0 for stop
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +int cdns3_drd_switch_host(struct cdns3 *cdns, int on)
> +{
> + int ret;
> + u32 reg = OTGCMD_OTG_DIS;
> +
> + /* switch OTG core */
> + if (on) {
> + writel(OTGCMD_HOST_BUS_REQ | reg, &cdns->otg_regs->cmd);
> +
> + dev_info(cdns->dev, "Waiting till Host mode is turned on\n");
> + ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_XHCI_READY,
> + OTGSTS_XHCI_READY, 100000);
> +
> + if (ret) {
> + dev_err(cdns->dev, "timeout waiting for xhci_ready\n");
> + return ret;
> + }
> + } else {
> + writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
> + OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
> + &cdns->otg_regs->cmd);
> + /* Waiting till H_IDLE state.*/
> + cdns3_handshake(&cdns->otg_regs->state,
> + OTGSTATE_HOST_STATE_MASK,
> + 0, 2000000);
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_drd_switch_gadget - start/stop gadget
> + * @cdns: Pointer to controller context structure
> + * @on: 1 for start, 0 for stop
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on)
> +{
> + int ret;
> + u32 reg = OTGCMD_OTG_DIS;
> +
> + /* switch OTG core */
> + if (on) {
> + writel(OTGCMD_DEV_BUS_REQ | reg, &cdns->otg_regs->cmd);
> +
> + dev_info(cdns->dev, "Waiting till Device mode is turned on\n");
> +
> + ret = cdns3_handshake(&cdns->otg_regs->sts, OTGSTS_DEV_READY,
> + OTGSTS_DEV_READY, 100000);
> +
> + if (ret) {
> + dev_err(cdns->dev, "timeout waiting for dev_ready\n");
> + return ret;
> + }
> + } else {
> + /*
> + * driver should wait at least 10us after disabling Device
> + * before turning-off Device (DEV_BUS_DROP)
> + */
> + usleep_range(20, 30);
> + writel(OTGCMD_HOST_BUS_DROP | OTGCMD_DEV_BUS_DROP |
> + OTGCMD_DEV_POWER_OFF | OTGCMD_HOST_POWER_OFF,
> + &cdns->otg_regs->cmd);
> + /* Waiting till DEV_IDLE state.*/
> + cdns3_handshake(&cdns->otg_regs->state, OTGSTATE_DEV_STATE_MASK,
> + 0, 2000000);

Don't care handshake result? the same comments for many other ones.

> + }
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_init_otg_mode - initialize drd controller
> + * @cdns: Pointer to controller context structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_init_otg_mode(struct cdns3 *cdns)
> +{
> + int ret = 0;
> +
> + cdns3_otg_disable_irq(cdns);
> + /* clear all interrupts */
> + writel(~0, &cdns->otg_regs->ivect);
> +
> + ret = cdns3_set_mode(cdns, USB_DR_MODE_OTG);
> + if (ret)
> + return ret;
> +
> + cdns3_otg_enable_irq(cdns);
> + return ret;
> +}
> +
> +/**
> + * cdns3_drd_update_mode - initialize mode of operation
> + * @cdns: Pointer to controller context structure
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +int cdns3_drd_update_mode(struct cdns3 *cdns)
> +{
> + int ret = 0;
> +
> + if (cdns->desired_dr_mode == cdns->current_dr_mode)
> + return ret;
> +
> + switch (cdns->desired_dr_mode) {
> + case USB_DR_MODE_PERIPHERAL:
> + ret = cdns3_set_mode(cdns, USB_DR_MODE_PERIPHERAL);
> + break;
> + case USB_DR_MODE_HOST:
> + ret = cdns3_set_mode(cdns, USB_DR_MODE_HOST);
> + break;
> + case USB_DR_MODE_OTG:
> + ret = cdns3_init_otg_mode(cdns);
> + break;
> + default:
> + dev_err(cdns->dev, "Unsupported mode of operation %d\n",
> + cdns->dr_mode);
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_drd_irq - interrupt handler for OTG events
> + *
> + * @irq: irq number for cdns3 core device
> + * @data: structure of cdns3
> + *
> + * Returns IRQ_HANDLED or IRQ_NONE
> + */
> +static irqreturn_t cdns3_drd_irq(int irq, void *data)
> +{
> + irqreturn_t ret = IRQ_NONE;
> + struct cdns3 *cdns = data;
> + u32 reg;
> +
> + if (cdns->dr_mode != USB_DR_MODE_OTG)
> + return ret;
> +
> + reg = readl(&cdns->otg_regs->ivect);
> +
> + if (!reg)
> + return ret;
> +
> + if (reg & OTGIEN_ID_CHANGE_INT) {
> + dev_dbg(cdns->dev, "OTG IRQ: new ID: %d\n",
> + cdns3_get_id(cdns));
> +
> + ret = IRQ_HANDLED;
> + }
> +
> + if (reg & (OTGIEN_VBUSVALID_RISE_INT | OTGIEN_VBUSVALID_FALL_INT)) {
> + dev_dbg(cdns->dev, "OTG IRQ: new VBUS: %d\n",
> + cdns3_get_vbus(cdns));
> +
> + ret = IRQ_HANDLED;
> + }
> +
> + if (ret == IRQ_HANDLED)
> + queue_work(system_freezable_wq, &cdns->role_switch_wq);
> +
> + writel(~0, &cdns->otg_regs->ivect);
> + return ret;
> +}
> +
> +int cdns3_drd_init(struct cdns3 *cdns)
> +{
> + void __iomem *regs;
> + int ret = 0;
> + u32 state;
> +
> + regs = devm_ioremap_resource(cdns->dev, &cdns->otg_res);
> + if (IS_ERR(regs))
> + return PTR_ERR(regs);
> +
> + /* Detection of DRD version. Controller has been released
> + * in two versions. Both are similar, but they have same changes
> + * in register maps.
> + * The first register in old version is command register and it's read
> + * only, so driver should read 0 from it. On the other hand, in v1
> + * the first register contains device ID number which is not set to 0.
> + * Driver uses this fact to detect the proper version of
> + * controller.
> + */
> + cdns->otg_v0_regs = regs;
> + if (!readl(&cdns->otg_v0_regs->cmd)) {
> + cdns->version = CDNS3_CONTROLLER_V0;
> + cdns->otg_v1_regs = NULL;
> + cdns->otg_regs = regs;
> + writel(1, &cdns->otg_v0_regs->simulate);
> + dev_info(cdns->dev, "DRD version v0 (%08x)\n",
> + readl(&cdns->otg_v0_regs->version));
> + } else {
> + cdns->otg_v0_regs = NULL;
> + cdns->otg_v1_regs = regs;
> + cdns->otg_regs = (void *)&cdns->otg_v1_regs->cmd;
> + cdns->version = CDNS3_CONTROLLER_V1;
> + writel(1, &cdns->otg_v1_regs->simulate);
> + dev_info(cdns->dev, "DRD version v1 (ID: %08x, rev: %08x)\n",
> + readl(&cdns->otg_v1_regs->did),
> + readl(&cdns->otg_v1_regs->rid));
> + }
> +
> + state = OTGSTS_STRAP(readl(&cdns->otg_regs->sts));
> +
> + /* Update dr_mode according to STRAP configuration. */
> + cdns->dr_mode = USB_DR_MODE_OTG;
> + if (state == OTGSTS_STRAP_HOST) {
> + dev_info(cdns->dev, "Controller strapped to HOST\n");
> + cdns->dr_mode = USB_DR_MODE_HOST;
> + } else if (state == OTGSTS_STRAP_GADGET) {
> + dev_info(cdns->dev, "Controller strapped to PERIPHERAL\n");
> + cdns->dr_mode = USB_DR_MODE_PERIPHERAL;
> + }
> +
> + cdns->desired_dr_mode = cdns->dr_mode;
> + cdns->current_dr_mode = USB_DR_MODE_UNKNOWN;
> +
> + ret = devm_request_threaded_irq(cdns->dev, cdns->otg_irq,
> + cdns3_drd_irq,
> + NULL, IRQF_SHARED,
> + dev_name(cdns->dev), cdns);
> +
> + if (ret) {
> + dev_err(cdns->dev, "couldn't get otg_irq\n");
> + return ret;
> + }
> +
> + state = readl(&cdns->otg_regs->sts);
> + if (OTGSTS_OTG_NRDY(state) != 0) {
> + dev_err(cdns->dev, "Cadence USB3 OTG device not ready\n");
> + return -ENODEV;
> + }
> +
> + return ret;
> +}
> +
> +int cdns3_drd_exit(struct cdns3 *cdns)
> +{
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/drd.h b/drivers/usb/cdns3/drd.h
> new file mode 100644
> index 000000000000..bf6c7bc41b58
> --- /dev/null
> +++ b/drivers/usb/cdns3/drd.h
> @@ -0,0 +1,166 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USB3 DRD header file.
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +#ifndef __LINUX_CDNS3_DRD
> +#define __LINUX_CDNS3_DRD
> +
> +#include <linux/usb/otg.h>
> +#include <linux/phy/phy.h>
> +#include "core.h"
> +
> +/* DRD register interface for version v1. */
> +struct cdns3_otg_regs {
> + __le32 did;
> + __le32 rid;
> + __le32 capabilities;
> + __le32 reserved1;
> + __le32 cmd;
> + __le32 sts;
> + __le32 state;
> + __le32 reserved2;
> + __le32 ien;
> + __le32 ivect;
> + __le32 refclk;
> + __le32 tmr;
> + __le32 reserved3[4];
> + __le32 simulate;
> + __le32 override;
> + __le32 susp_ctrl;
> + __le32 reserved4;
> + __le32 anasts;
> + __le32 adp_ramp_time;
> + __le32 ctrl1;
> + __le32 ctrl2;
> +};
> +
> +/* DRD register interface for version v0. */
> +struct cdns3_otg_legacy_regs {
> + __le32 cmd;
> + __le32 sts;
> + __le32 state;
> + __le32 refclk;
> + __le32 ien;
> + __le32 ivect;
> + __le32 reserved1[3];
> + __le32 tmr;
> + __le32 reserved2[2];
> + __le32 version;
> + __le32 capabilities;
> + __le32 reserved3[2];
> + __le32 simulate;
> + __le32 reserved4[5];
> + __le32 ctrl1;
> +};
> +
> +/*
> + * Common registers interface for both version of DRD.
> + */
> +struct cdns3_otg_common_regs {
> + __le32 cmd;
> + __le32 sts;
> + __le32 state;
> + __le32 different1;
> + __le32 ien;
> + __le32 ivect;
> +};
> +
> +/* CDNS_RID - bitmasks */
> +#define CDNS_RID(p) ((p) & GENMASK(15, 0))
> +
> +/* CDNS_VID - bitmasks */
> +#define CDNS_DID(p) ((p) & GENMASK(31, 0))
> +
> +/* OTGCMD - bitmasks */
> +/* "Request the bus for Device mode. */
> +#define OTGCMD_DEV_BUS_REQ BIT(0)
> +/* Request the bus for Host mode */
> +#define OTGCMD_HOST_BUS_REQ BIT(1)
> +/* Enable OTG mode. */
> +#define OTGCMD_OTG_EN BIT(2)
> +/* Disable OTG mode */
> +#define OTGCMD_OTG_DIS BIT(3)
> +/*"Configure OTG as A-Device. */
> +#define OTGCMD_A_DEV_EN BIT(4)
> +/*"Configure OTG as A-Device. */
> +#define OTGCMD_A_DEV_DIS BIT(5)
> +/* Drop the bus for Device mod e. */
> +#define OTGCMD_DEV_BUS_DROP BIT(8)
> +/* Drop the bus for Host mode*/
> +#define OTGCMD_HOST_BUS_DROP BIT(9)
> +/* Power Down USBSS-DEV. */
> +#define OTGCMD_DEV_POWER_OFF BIT(11)
> +/* Power Down CDNSXHCI. */
> +#define OTGCMD_HOST_POWER_OFF BIT(12)
> +
> +/* OTGIEN - bitmasks */
> +/* ID change interrupt enable */
> +#define OTGIEN_ID_CHANGE_INT BIT(0)
> +/* Vbusvalid fall detected interrupt enable.*/
> +#define OTGIEN_VBUSVALID_RISE_INT BIT(4)
> +/* Vbusvalid fall detected interrupt enable */
> +#define OTGIEN_VBUSVALID_FALL_INT BIT(5)
> +
> +/* OTGSTS - bitmasks */
> +/*
> + * Current value of the ID pin. It is only valid when idpullup in
> + * OTGCTRL1_TYPE register is set to '1'.
> + */
> +#define OTGSTS_ID_VALUE BIT(0)
> +/* Current value of the vbus_valid */
> +#define OTGSTS_VBUS_VALID BIT(1)
> +/* Current value of the b_sess_vld */
> +#define OTGSTS_SESSION_VALID BIT(2)
> +/*Device mode is active*/
> +#define OTGSTS_DEV_ACTIVE BIT(3)
> +/* Host mode is active. */
> +#define OTGSTS_HOST_ACTIVE BIT(4)
> +/* OTG Controller not ready. */
> +#define OTGSTS_OTG_NRDY_MASK BIT(11)
> +#define OTGSTS_OTG_NRDY(p) ((p) & OTGSTS_OTG_NRDY_MASK)
> +/*
> + * Value of the strap pins.
> + * 000 - no default configuration
> + * 010 - Controller initiall configured as Host
> + * 100 - Controller initially configured as Device
> + */
> +#define OTGSTS_STRAP(p) (((p) & GENMASK(14, 12)) >> 12)
> +#define OTGSTS_STRAP_NO_DEFAULT_CFG 0x00
> +#define OTGSTS_STRAP_HOST_OTG 0x01
> +#define OTGSTS_STRAP_HOST 0x02
> +#define OTGSTS_STRAP_GADGET 0x04
> +/* Host mode is turned on. */
> +#define OTGSTS_XHCI_READY BIT(26)
> +/* "Device mode is turned on .*/
> +#define OTGSTS_DEV_READY BIT(27)
> +
> +/* OTGSTATE- bitmasks */
> +#define OTGSTATE_DEV_STATE_MASK GENMASK(2, 0)
> +#define OTGSTATE_HOST_STATE_MASK GENMASK(5, 3)
> +#define OTGSTATE_HOST_STATE_IDLE 0x0
> +#define OTGSTATE_HOST_STATE_VBUS_FALL 0x7
> +#define OTGSTATE_HOST_STATE(p) (((p) & OTGSTATE_HOST_STATE_MASK) >> 3)
> +
> +/* OTGREFCLK - bitmasks */
> +#define OTGREFCLK_STB_CLK_SWITCH_EN BIT(31)
> +
> +/* OVERRIDE - bitmasks */
> +#define OVERRIDE_IDPULLUP BIT(0)
> +/* Only for CDNS3_CONTROLLER_V0 version */
> +#define OVERRIDE_IDPULLUP_V0 BIT(24)
> +
> +int cdns3_is_host(struct cdns3 *cdns);
> +int cdns3_is_device(struct cdns3 *cdns);
> +int cdns3_get_id(struct cdns3 *cdns);
> +int cdns3_get_vbus(struct cdns3 *cdns);
> +int cdns3_drd_init(struct cdns3 *cdns);
> +int cdns3_drd_exit(struct cdns3 *cdns);
> +int cdns3_drd_update_mode(struct cdns3 *cdns);
> +int cdns3_drd_switch_gadget(struct cdns3 *cdns, int on);
> +int cdns3_drd_switch_host(struct cdns3 *cdns, int on);
> +
> +#endif /* __LINUX_CDNS3_DRD */
> diff --git a/drivers/usb/cdns3/ep0.c b/drivers/usb/cdns3/ep0.c
> new file mode 100644
> index 000000000000..dcc7a1b91e1b
> --- /dev/null
> +++ b/drivers/usb/cdns3/ep0.c
> @@ -0,0 +1,915 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - gadget side.
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Pawel Jez <pjez@xxxxxxxxxxx>,
> + * Pawel Laszczak <pawell@xxxxxxxxxxx>
> + * Peter Chen <peter.chen@xxxxxxx>
> + */
> +
> +#include <linux/usb/composite.h>
> +
> +#include "gadget.h"
> +#include "trace.h"
> +
> +static struct usb_endpoint_descriptor cdns3_gadget_ep0_desc = {
> + .bLength = USB_DT_ENDPOINT_SIZE,
> + .bDescriptorType = USB_DT_ENDPOINT,
> + .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
> +};
> +
> +/**
> + * cdns3_ep0_run_transfer - Do transfer on default endpoint hardware
> + * @priv_dev: extended gadget object
> + * @dma_addr: physical address where data is/will be stored
> + * @length: data length
> + * @erdy: set it to 1 when ERDY packet should be sent -
> + * exit from flow control state
> + */
> +static void cdns3_ep0_run_transfer(struct cdns3_device *priv_dev,
> + dma_addr_t dma_addr,
> + unsigned int length, int erdy, int zlp)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> + struct cdns3_endpoint *priv_ep = priv_dev->eps[0];
> +
> + priv_ep->trb_pool[0].buffer = TRB_BUFFER(dma_addr);
> + priv_ep->trb_pool[0].length = TRB_LEN(length);
> +
> + if (zlp) {
> + priv_ep->trb_pool[0].control = TRB_CYCLE | TRB_TYPE(TRB_NORMAL);
> + priv_ep->trb_pool[1].buffer = TRB_BUFFER(dma_addr);
> + priv_ep->trb_pool[1].length = TRB_LEN(0);
> + priv_ep->trb_pool[1].control = TRB_CYCLE | TRB_IOC |
> + TRB_TYPE(TRB_NORMAL);
> + } else {
> + priv_ep->trb_pool[0].control = TRB_CYCLE | TRB_IOC |
> + TRB_TYPE(TRB_NORMAL);
> + priv_ep->trb_pool[1].control = 0;
> + }
> +
> + trace_cdns3_prepare_trb(priv_ep, priv_ep->trb_pool);
> +
> + cdns3_select_ep(priv_dev, priv_dev->ep0_data_dir);
> +
> + writel(EP_STS_TRBERR, &regs->ep_sts);
> + writel(EP_TRADDR_TRADDR(priv_ep->trb_pool_dma), &regs->ep_traddr);
> + trace_cdns3_doorbell_ep0(priv_dev->ep0_data_dir ? "ep0in" : "ep0out",
> + readl(&regs->ep_traddr));
> +
> + /* Resume controller before arming transfer. */
> + __cdns3_gadget_wakeup(priv_dev);
> +
> + /* TRB should be prepared before starting transfer. */
> + writel(EP_CMD_DRDY, &regs->ep_cmd);
> +
> + if (erdy)
> + writel(EP_CMD_ERDY, &priv_dev->regs->ep_cmd);
> +}
> +
> +/**
> + * cdns3_ep0_delegate_req - Returns status of handling setup packet
> + * Setup is handled by gadget driver
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns zero on success or negative value on failure
> + */
> +static int cdns3_ep0_delegate_req(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + int ret;
> +
> + spin_unlock(&priv_dev->lock);
> + priv_dev->setup_pending = 1;
> + ret = priv_dev->gadget_driver->setup(&priv_dev->gadget, ctrl_req);
> + priv_dev->setup_pending = 0;
> + spin_lock(&priv_dev->lock);
> + return ret;
> +}
> +
> +static void cdns3_prepare_setup_packet(struct cdns3_device *priv_dev)
> +{
> + priv_dev->ep0_data_dir = 0;
> + priv_dev->ep0_stage = CDNS3_SETUP_STAGE;
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
> + sizeof(struct usb_ctrlrequest), 0, 0);
> +}
> +
> +static void cdns3_ep0_complete_setup(struct cdns3_device *priv_dev,
> + u8 send_stall, u8 send_erdy)
> +{
> + struct cdns3_endpoint *priv_ep = priv_dev->eps[0];
> + struct usb_request *request;
> +
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> + if (request)
> + list_del_init(&request->list);
> +
> + if (send_stall) {
> + cdns3_dbg(priv_ep->cdns3_dev, "STALL for ep0\n");
> + /* set_stall on ep0 */
> + cdns3_select_ep(priv_dev, 0x00);
> + writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
> + } else {
> + cdns3_prepare_setup_packet(priv_dev);
> + }
> +
> + priv_dev->ep0_stage = CDNS3_SETUP_STAGE;
> + writel((send_erdy ? EP_CMD_ERDY : 0) | EP_CMD_REQ_CMPL,
> + &priv_dev->regs->ep_cmd);
> +}
> +
> +/**
> + * cdns3_req_ep0_set_configuration - Handling of SET_CONFIG standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, USB_GADGET_DELAYED_STATUS on deferred status stage,
> + * error code on error
> + */
> +static int cdns3_req_ep0_set_configuration(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + enum usb_device_state device_state = priv_dev->gadget.state;
> + struct cdns3_endpoint *priv_ep;
> + u32 config = le16_to_cpu(ctrl_req->wValue);
> + int result = 0;
> + int i;
> +
> + switch (device_state) {
> + case USB_STATE_ADDRESS:
> + /* Configure non-control EPs */
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
> + priv_ep = priv_dev->eps[i];
> + if (!priv_ep)
> + continue;
> +
> + if (priv_ep->flags & EP_CLAIMED)
> + cdns3_ep_config(priv_ep);
> + }
> +
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> +
> + if (result)
> + return result;
> +
> + if (config) {
> + cdns3_set_hw_configuration(priv_dev);
> + } else {
> + cdns3_hw_reset_eps_config(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget,
> + USB_STATE_ADDRESS);
> + }
> + break;
> + case USB_STATE_CONFIGURED:
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> +
> + if (!config && !result) {
> + cdns3_hw_reset_eps_config(priv_dev);
> + usb_gadget_set_state(&priv_dev->gadget,
> + USB_STATE_ADDRESS);
> + }
> + break;
> + default:
> + result = -EINVAL;
> + }
> +
> + return result;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_address - Handling of SET_ADDRESS standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_address(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + enum usb_device_state device_state = priv_dev->gadget.state;
> + u32 reg;
> + u32 addr;
> +
> + addr = le16_to_cpu(ctrl_req->wValue);
> +
> + if (addr > USB_DEVICE_MAX_ADDRESS) {
> + dev_err(priv_dev->dev,
> + "Device address (%d) cannot be greater than %d\n",
> + addr, USB_DEVICE_MAX_ADDRESS);
> + return -EINVAL;
> + }
> +
> + if (device_state == USB_STATE_CONFIGURED) {
> + dev_err(priv_dev->dev,
> + "can't set_address from configured state\n");
> + return -EINVAL;
> + }
> +
> + reg = readl(&priv_dev->regs->usb_cmd);
> +
> + writel(reg | USB_CMD_FADDR(addr) | USB_CMD_SET_ADDR,
> + &priv_dev->regs->usb_cmd);
> +
> + usb_gadget_set_state(&priv_dev->gadget,
> + (addr ? USB_STATE_ADDRESS : USB_STATE_DEFAULT));
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_req_ep0_get_status - Handling of GET_STATUS standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_get_status(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl)
> +{
> + __le16 *response_pkt;
> + u16 usb_status = 0;
> + u32 recip;
> + u32 reg;
> +
> + recip = ctrl->bRequestType & USB_RECIP_MASK;
> +
> + switch (recip) {
> + case USB_RECIP_DEVICE:
> + /* self powered */
> + if (priv_dev->is_selfpowered)
> + usb_status = BIT(USB_DEVICE_SELF_POWERED);
> +
> + if (priv_dev->wake_up_flag)
> + usb_status |= BIT(USB_DEVICE_REMOTE_WAKEUP);
> +
> + if (priv_dev->gadget.speed != USB_SPEED_SUPER)
> + break;
> +
> + reg = readl(&priv_dev->regs->usb_sts);
> +
> + if (priv_dev->u1_allowed)
> + usb_status |= BIT(USB_DEV_STAT_U1_ENABLED);
> +
> + if (priv_dev->u2_allowed)
> + usb_status |= BIT(USB_DEV_STAT_U2_ENABLED);
> +
> + break;
> + case USB_RECIP_INTERFACE:
> + return cdns3_ep0_delegate_req(priv_dev, ctrl);
> + case USB_RECIP_ENDPOINT:
> + /* check if endpoint is stalled */
> + cdns3_select_ep(priv_dev, ctrl->wIndex);
> + if (EP_STS_STALL(readl(&priv_dev->regs->ep_sts)))
> + usb_status = BIT(USB_ENDPOINT_HALT);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + response_pkt = (__le16 *)priv_dev->setup_buf;
> + *response_pkt = cpu_to_le16(usb_status);
> +
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma,
> + sizeof(*response_pkt), 1, 0);
> + return 0;
> +}
> +
> +static int cdns3_ep0_feature_handle_device(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + enum usb_device_state state;
> + enum usb_device_speed speed;
> + int ret = 0;
> + u32 wValue;
> + u32 wIndex;
> + u16 tmode;
> +
> + wValue = le16_to_cpu(ctrl->wValue);
> + wIndex = le16_to_cpu(ctrl->wIndex);
> + state = priv_dev->gadget.state;
> + speed = priv_dev->gadget.speed;
> +
> + switch (ctrl->wValue) {
> + case USB_DEVICE_REMOTE_WAKEUP:
> + priv_dev->wake_up_flag = !!set;
> + break;
> + case USB_DEVICE_U1_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u1_allowed = !!set;
> + break;
> + case USB_DEVICE_U2_ENABLE:
> + if (state != USB_STATE_CONFIGURED || speed != USB_SPEED_SUPER)
> + return -EINVAL;
> +
> + priv_dev->u2_allowed = !!set;
> + break;
> + case USB_DEVICE_LTM_ENABLE:
> + ret = -EINVAL;
> + break;
> + case USB_DEVICE_TEST_MODE:
> + if (state != USB_STATE_CONFIGURED || speed > USB_SPEED_HIGH)
> + return -EINVAL;
> +
> + tmode = le16_to_cpu(ctrl->wIndex);
> +
> + if (!set || (tmode & 0xff) != 0)
> + return -EINVAL;
> +
> + switch (tmode >> 8) {
> + case TEST_J:
> + case TEST_K:
> + case TEST_SE0_NAK:
> + case TEST_PACKET:
> + cdns3_ep0_complete_setup(priv_dev, 0, 1);
> + /**
> + * Little delay to give the controller some time
> + * for sending status stage.
> + * This time should be less then 3ms.
> + */
> + usleep_range(1000, 2000);
> + cdns3_set_register_bit(&priv_dev->regs->usb_cmd,
> + USB_CMD_STMODE |
> + USB_STS_TMODE_SEL(tmode - 1));
> + break;
> + default:
> + ret = -EINVAL;
> + }
> + break;
> + default:
> + ret = -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int cdns3_ep0_feature_handle_intf(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + u32 wValue;
> + int ret = 0;
> +
> + wValue = le16_to_cpu(ctrl->wValue);
> +
> + switch (wValue) {
> + case USB_INTRF_FUNC_SUSPEND:
> + break;
> + default:
> + ret = -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int cdns3_ep0_feature_handle_endpoint(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + struct cdns3_endpoint *priv_ep;
> + int ret = 0;
> + u8 index;
> +
> + if (le16_to_cpu(ctrl->wValue) != USB_ENDPOINT_HALT)
> + return -EINVAL;
> +
> + if (!(ctrl->wIndex & ~USB_DIR_IN))
> + return 0;
> +
> + index = cdns3_ep_addr_to_index(ctrl->wIndex);
> + priv_ep = priv_dev->eps[index];
> +
> + cdns3_select_ep(priv_dev, ctrl->wIndex);

It's better to use the ep num, not ctrl->wIndex.

> +
> + if (set) {
> + cdns3_dbg(priv_ep->cdns3_dev, "Stall endpoint %s\n",
> + priv_ep->name);
> + writel(EP_CMD_SSTALL, &priv_dev->regs->ep_cmd);
> + priv_ep->flags |= EP_STALL;
> + } else {
> + struct usb_request *request;
> +
> + if (priv_dev->eps[index]->flags & EP_WEDGE) {
> + cdns3_select_ep(priv_dev, 0x00);

Still need select ep before return ?

> + return 0;
> + }
> +
> + cdns3_dbg(priv_ep->cdns3_dev, "Clear Stalled endpoint %s\n",
> + priv_ep->name);
> +
> + writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + /* wait for EPRST cleared */
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + if (ret)
> + return -EINVAL;
> +
> + priv_ep->flags &= ~EP_STALL;
> +
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> + if (request) {
> + cdns3_dbg(priv_ep->cdns3_dev, "Resume transfer for %s\n",
> + priv_ep->name);
> +
> + cdns3_rearm_transfer(priv_ep, 1);
> + }
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_req_ep0_handle_feature -
> + * Handling of GET/SET_FEATURE standard USB request
> + *
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet

ctrl

> + * @set: must be set to 1 for SET_FEATURE request
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_handle_feature(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl,
> + int set)
> +{
> + int ret = 0;
> + u32 recip;
> +
> + recip = ctrl->bRequestType & USB_RECIP_MASK;
> +
> + switch (recip) {
> + case USB_RECIP_DEVICE:
> + ret = cdns3_ep0_feature_handle_device(priv_dev, ctrl, set);
> + break;
> + case USB_RECIP_INTERFACE:
> + ret = cdns3_ep0_feature_handle_intf(priv_dev, ctrl, set);
> + break;
> + case USB_RECIP_ENDPOINT:
> + ret = cdns3_ep0_feature_handle_endpoint(priv_dev, ctrl, set);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_sel - Handling of SET_SEL standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_sel(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + if (priv_dev->gadget.state < USB_STATE_ADDRESS)
> + return -EINVAL;
> +
> + if (ctrl_req->wLength != 6) {

le16_to_cpu(ctrl_req->wLength)?

> + dev_err(priv_dev->dev, "Set SEL should be 6 bytes, got %d\n",
> + ctrl_req->wLength);
> + return -EINVAL;
> + }
> +
> + cdns3_ep0_run_transfer(priv_dev, priv_dev->setup_dma, 6, 1, 0);
> + return 0;
> +}
> +
> +/**
> + * cdns3_req_ep0_set_isoch_delay -
> + * Handling of GET_ISOCH_DELAY standard USB request
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_req_ep0_set_isoch_delay(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + if (ctrl_req->wIndex || ctrl_req->wLength)
> + return -EINVAL;
> +
> + priv_dev->isoch_delay = ctrl_req->wValue;
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_ep0_standard_request - Handling standard USB requests
> + * @priv_dev: extended gadget object
> + * @ctrl_req: pointer to received setup packet
> + *
> + * Returns 0 if success, error code on error
> + */
> +static int cdns3_ep0_standard_request(struct cdns3_device *priv_dev,
> + struct usb_ctrlrequest *ctrl_req)
> +{
> + int ret;
> +
> + switch (ctrl_req->bRequest) {
> + case USB_REQ_SET_ADDRESS:
> + ret = cdns3_req_ep0_set_address(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_SET_CONFIGURATION:
> + ret = cdns3_req_ep0_set_configuration(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_GET_STATUS:
> + ret = cdns3_req_ep0_get_status(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_CLEAR_FEATURE:
> + ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 0);
> + break;
> + case USB_REQ_SET_FEATURE:
> + ret = cdns3_req_ep0_handle_feature(priv_dev, ctrl_req, 1);
> + break;
> + case USB_REQ_SET_SEL:
> + ret = cdns3_req_ep0_set_sel(priv_dev, ctrl_req);
> + break;
> + case USB_REQ_SET_ISOCH_DELAY:
> + ret = cdns3_req_ep0_set_isoch_delay(priv_dev, ctrl_req);
> + break;
> + default:
> + ret = cdns3_ep0_delegate_req(priv_dev, ctrl_req);
> + break;
> + }
> +
> + return ret;
> +}
> +
> +static void __pending_setup_status_handler(struct cdns3_device *priv_dev)
> +{
> + struct usb_request *request = priv_dev->pending_status_request;
> +
> + if (priv_dev->status_completion_no_call && request &&
> + request->complete) {
> + request->complete(&priv_dev->eps[0]->endpoint, request);
> + priv_dev->status_completion_no_call = 0;
> + }
> +}
> +
> +void cdns3_pending_setup_status_handler(struct work_struct *work)
> +{
> + struct cdns3_device *priv_dev = container_of(work, struct cdns3_device,
> + pending_status_wq);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);

request->complete() be called with spin lock hold?

> + __pending_setup_status_handler(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +}
> +
> +/**
> + * cdns3_ep0_setup_phase - Handling setup USB requests
> + * @priv_dev: extended gadget object
> + */
> +static void cdns3_ep0_setup_phase(struct cdns3_device *priv_dev)
> +{
> + struct usb_ctrlrequest *ctrl = priv_dev->setup_buf;
> + struct cdns3_endpoint *priv_ep = priv_dev->eps[0];
> + int result;
> +
> + priv_dev->ep0_data_dir = ctrl->bRequestType & USB_DIR_IN;
> +
> + trace_cdns3_ctrl_req(ctrl);
> +
> + if (!list_empty(&priv_ep->pending_req_list)) {
> + struct usb_request *request;
> +
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> + priv_ep->dir = priv_dev->ep0_data_dir;
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request),
> + -ECONNRESET);
> + }
> +
> + if (le16_to_cpu(ctrl->wLength))
> + priv_dev->ep0_stage = CDNS3_DATA_STAGE;
> + else
> + priv_dev->ep0_stage = CDNS3_STATUS_STAGE;
> +
> + if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
> + result = cdns3_ep0_standard_request(priv_dev, ctrl);
> + else
> + result = cdns3_ep0_delegate_req(priv_dev, ctrl);
> +
> + if (result == USB_GADGET_DELAYED_STATUS)
> + return;
> +
> + if (result < 0)
> + cdns3_ep0_complete_setup(priv_dev, 1, 1);
> + else if (priv_dev->ep0_stage == CDNS3_STATUS_STAGE)
> + cdns3_ep0_complete_setup(priv_dev, 0, 1);
> +}
> +
> +static void cdns3_transfer_completed(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_endpoint *priv_ep = priv_dev->eps[0];
> +
> + if (!list_empty(&priv_ep->pending_req_list)) {
> + struct usb_request *request;
> +
> + trace_cdns3_complete_trb(priv_ep, priv_ep->trb_pool);
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> +
> + request->actual =
> + TRB_LEN(le32_to_cpu(priv_ep->trb_pool->length));
> +
> + priv_ep->dir = priv_dev->ep0_data_dir;
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request), 0);
> + }
> +
> + cdns3_ep0_complete_setup(priv_dev, 0, 0);
> +}
> +
> +/**
> + * cdns3_check_new_setup - Check if controller receive new SETUP packet.
> + * @priv_dev: extended gadget object
> + *
> + * The SETUP packet can be kept in on-chip memory or in system memory.
> + */
> +static bool cdns3_check_new_setup(struct cdns3_device *priv_dev)
> +{
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, 0 | USB_DIR_OUT);
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> +
> + return !!(ep_sts_reg & (EP_STS_SETUP | EP_STS_STPWAIT));
> +}
> +
> +/**
> + * cdns3_check_ep0_interrupt_proceed - Processes interrupt related to endpoint 0
> + * @priv_dev: extended gadget object
> + * @dir: USB_DIR_IN for IN direction, USB_DIR_OUT for OUT direction
> + */
> +void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir)
> +{
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, dir);
> +
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> + writel(ep_sts_reg, &priv_dev->regs->ep_sts);
> +
> + trace_cdns3_ep0_irq(priv_dev, ep_sts_reg);
> +
> + __pending_setup_status_handler(priv_dev);
> +
> + if (ep_sts_reg & EP_STS_SETUP)
> + priv_dev->wait_for_setup = 1;
> +
> + if (priv_dev->wait_for_setup && ep_sts_reg & EP_STS_IOC) {
> + priv_dev->wait_for_setup = 0;
> + cdns3_ep0_setup_phase(priv_dev);
> + } else if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP)) {
> + priv_dev->ep0_data_dir = dir;
> + cdns3_transfer_completed(priv_dev);
> + }
> +
> + if (ep_sts_reg & EP_STS_DESCMIS) {
> + if (dir == 0 && !priv_dev->setup_pending)
> + cdns3_prepare_setup_packet(priv_dev);
> + }
> +}
> +
> +/**
> + * cdns3_gadget_ep0_enable
> + * Function shouldn't be called by gadget driver,
> + * endpoint 0 is allways active
> + */
> +static int cdns3_gadget_ep0_enable(struct usb_ep *ep,
> + const struct usb_endpoint_descriptor *desc)
> +{
> + return -EINVAL;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_disable
> + * Function shouldn't be called by gadget driver,
> + * endpoint 0 is allways active
> + */
> +static int cdns3_gadget_ep0_disable(struct usb_ep *ep)
> +{
> + return -EINVAL;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_set_halt
> + * @ep: pointer to endpoint zero object
> + * @value: 1 for set stall, 0 for clear stall
> + *
> + * Returns 0
> + */
> +static int cdns3_gadget_ep0_set_halt(struct usb_ep *ep, int value)
> +{
> + /* TODO */
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_ep0_queue Transfer data on endpoint zero
> + * @ep: pointer to endpoint zero object
> + * @request: pointer to request object
> + * @gfp_flags: gfp flags
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep0_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + unsigned long flags;
> + int erdy_sent = 0;
> + int ret = 0;
> + u8 zlp = 0;
> +
> + cdns3_dbg(priv_ep->cdns3_dev, "Queue to Ep0%s L: %d\n",
> + priv_dev->ep0_data_dir ? "IN" : "OUT",
> + request->length);
> +
> + /* cancel the request if controller receive new SETUP packet. */
> + if (cdns3_check_new_setup(priv_dev))
> + return -ECONNRESET;
> +
> + /* send STATUS stage. Should be called only for SET_CONFIGURATION */
> + if (priv_dev->ep0_stage == CDNS3_STATUS_STAGE) {
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + cdns3_select_ep(priv_dev, 0x00);
> +
> + erdy_sent = !priv_dev->hw_configured_flag;
> + cdns3_set_hw_configuration(priv_dev);
> +
> + if (!erdy_sent)
> + cdns3_ep0_complete_setup(priv_dev, 0, 1);
> +
> + request->actual = 0;
> + priv_dev->status_completion_no_call = true;
> + priv_dev->pending_status_request = request;
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + /*
> + * Since there is no completion interrupt for status stage,
> + * it needs to call ->completion in software after
> + * ep0_queue is back.
> + */
> + queue_work(system_freezable_wq, &priv_dev->pending_status_wq);
> + return 0;
> + }
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + if (!list_empty(&priv_ep->pending_req_list)) {
> + dev_err(priv_dev->dev,
> + "can't handle multiple requests for ep0\n");
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return -EBUSY;
> + }
> +
> + ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
> + priv_dev->ep0_data_dir);
> + if (ret) {
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + dev_err(priv_dev->dev, "failed to map request\n");
> + return -EINVAL;
> + }
> +
> + request->status = -EINPROGRESS;
> + list_add_tail(&request->list, &priv_ep->pending_req_list);
> +
> + if (request->zero && request->length &&
> + (request->length % ep->maxpacket == 0))
> + zlp = 1;
> +
> + cdns3_ep0_run_transfer(priv_dev, request->dma, request->length, 1, zlp);
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_set_wedge Set wedge on selected endpoint
> + * @ep: endpoint object
> + *
> + * Returns 0
> + */
> +int cdns3_gadget_ep_set_wedge(struct usb_ep *ep)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + dev_dbg(priv_dev->dev, "Wedge for %s\n", ep->name);
> + cdns3_gadget_ep_set_halt(ep, 1);
> + priv_ep->flags |= EP_WEDGE;
> +
> + return 0;
> +}
> +
> +const struct usb_ep_ops cdns3_gadget_ep0_ops = {
> + .enable = cdns3_gadget_ep0_enable,
> + .disable = cdns3_gadget_ep0_disable,
> + .alloc_request = cdns3_gadget_ep_alloc_request,
> + .free_request = cdns3_gadget_ep_free_request,
> + .queue = cdns3_gadget_ep0_queue,
> + .dequeue = cdns3_gadget_ep_dequeue,
> + .set_halt = cdns3_gadget_ep0_set_halt,
> + .set_wedge = cdns3_gadget_ep_set_wedge,
> +};
> +
> +/**
> + * cdns3_ep0_config - Configures default endpoint
> + * @priv_dev: extended gadget object
> + *
> + * Functions sets parameters: maximal packet size and enables interrupts
> + */
> +void cdns3_ep0_config(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_usb_regs __iomem *regs;
> + struct cdns3_endpoint *priv_ep;
> + u32 max_packet_size = 64;
> +
> + regs = priv_dev->regs;
> +
> + if (priv_dev->gadget.speed == USB_SPEED_SUPER)
> + max_packet_size = 512;
> +
> + priv_ep = priv_dev->eps[0];
> +
> + if (!list_empty(&priv_ep->pending_req_list)) {
> + struct usb_request *request;
> +
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> + list_del_init(&request->list);
> + }
> +
> + priv_dev->u1_allowed = 0;
> + priv_dev->u2_allowed = 0;
> +
> + priv_dev->gadget.ep0->maxpacket = max_packet_size;
> + cdns3_gadget_ep0_desc.wMaxPacketSize = cpu_to_le16(max_packet_size);
> +
> + /* init ep out */
> + cdns3_select_ep(priv_dev, USB_DIR_OUT);
> +
> + if (priv_dev->dev_ver >= DEV_VER_V3) {
> + cdns3_set_register_bit(&priv_dev->regs->dtrans,
> + BIT(0) | BIT(16));
> + cdns3_set_register_bit(&priv_dev->regs->tdl_from_trb,
> + BIT(0) | BIT(16));
> + }
> +
> + writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
> + &regs->ep_cfg);
> +
> + writel(EP_STS_EN_SETUPEN | EP_STS_EN_DESCMISEN | EP_STS_EN_TRBERREN,
> + &regs->ep_sts_en);
> +
> + /* init ep in */
> + cdns3_select_ep(priv_dev, USB_DIR_IN);
> +
> + writel(EP_CFG_ENABLE | EP_CFG_MAXPKTSIZE(max_packet_size),
> + &regs->ep_cfg);
> +
> + writel(EP_STS_EN_SETUPEN | EP_STS_EN_TRBERREN, &regs->ep_sts_en);
> +
> + cdns3_set_register_bit(&regs->usb_conf, USB_CONF_U1DS | USB_CONF_U2DS);
> +}
> +
> +/**
> + * cdns3_init_ep0 Initializes software endpoint 0 of gadget
> + * @priv_dev: extended gadget object
> + * @ep_priv: extended endpoint object
> + *
> + * Returns 0 on success else error code.
> + */
> +int cdns3_init_ep0(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + sprintf(priv_ep->name, "ep0");
> +
> + /* fill linux fields */
> + priv_ep->endpoint.ops = &cdns3_gadget_ep0_ops;
> + priv_ep->endpoint.maxburst = 1;
> + usb_ep_set_maxpacket_limit(&priv_ep->endpoint,
> + CDNS3_EP0_MAX_PACKET_LIMIT);
> + priv_ep->endpoint.address = 0;
> + priv_ep->endpoint.caps.type_control = 1;
> + priv_ep->endpoint.caps.dir_in = 1;
> + priv_ep->endpoint.caps.dir_out = 1;
> + priv_ep->endpoint.name = priv_ep->name;
> + priv_ep->endpoint.desc = &cdns3_gadget_ep0_desc;
> + priv_dev->gadget.ep0 = &priv_ep->endpoint;
> + priv_ep->type = USB_ENDPOINT_XFER_CONTROL;
> +
> + return cdns3_allocate_trb_pool(priv_ep);
> +}
> diff --git a/drivers/usb/cdns3/gadget-export.h b/drivers/usb/cdns3/gadget-export.h
> new file mode 100644
> index 000000000000..577469eee961
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget-export.h
> @@ -0,0 +1,28 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver - Gadget Export APIs.
> + *
> + * Copyright (C) 2017 NXP
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <peter.chen@xxxxxxx>
> + */
> +#ifndef __LINUX_CDNS3_GADGET_EXPORT
> +#define __LINUX_CDNS3_GADGET_EXPORT
> +
> +#ifdef CONFIG_USB_CDNS3_GADGET
> +
> +int cdns3_gadget_init(struct cdns3 *cdns);
> +void cdns3_gadget_exit(struct cdns3 *cdns);
> +#else
> +
> +static inline int cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + return -ENXIO;
> +}
> +
> +static inline void cdns3_gadget_exit(struct cdns3 *cdns) { }
> +
> +#endif
> +
> +#endif /* __LINUX_CDNS3_GADGET_EXPORT */
> diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
> new file mode 100644
> index 000000000000..f3b22ec43c0a
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget.c
> @@ -0,0 +1,2290 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - gadget side.
> + *
> + * Copyright (C) 2018-2019 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Pawel Jez <pjez@xxxxxxxxxxx>,
> + * Pawel Laszczak <pawell@xxxxxxxxxxx>
> + * Peter Chen <peter.chen@xxxxxxx>
> + */
> +
> +/*
> + * Work around 1:
> + * At some situations, the controller may get stale data address in TRB
> + * at below sequences:
> + * 1. Controller read TRB includes data address
> + * 2. Software updates TRBs includes data address and Cycle bit
> + * 3. Controller read TRB which includes Cycle bit
> + * 4. DMA run with stale data address
> + *
> + * To fix this problem, driver needs to make the first TRB in TD as invalid.
> + * After preparing all TRBs driver needs to check the position of DMA and
> + * if the DMA point to the first just added TRB and doorbell is 1,
> + * then driver must defer making this TRB as valid. This TRB will be make
> + * as valid during adding next TRB only if DMA is stopped or at TRBERR
> + * interrupt.
> + *
> + * Issue has been fixed in DEV_VER_V3 version of controller.
> + *
> + */
> +
> +#include <linux/dma-mapping.h>
> +#include <linux/usb/gadget.h>
> +#include <linux/module.h>
> +
> +#include "core.h"
> +#include "gadget-export.h"
> +#include "gadget.h"
> +#include "trace.h"
> +#include "drd.h"
> +
> +static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags);
> +
> +/**
> + * cdns3_set_register_bit - set bit in given register.
> + * @ptr: address of device controller register to be read and changed
> + * @mask: bits requested to set
> + */
> +void cdns3_set_register_bit(void __iomem *ptr, u32 mask)
> +{
> + mask = readl(ptr) | mask;
> + writel(mask, ptr);
> +}
> +
> +/**
> + * cdns3_ep_addr_to_index - Macro converts endpoint address to
> + * index of endpoint object in cdns3_device.eps[] container
> + * @ep_addr: endpoint address for which endpoint object is required
> + *
> + */
> +u8 cdns3_ep_addr_to_index(u8 ep_addr)
> +{
> + return (((ep_addr & 0x7F)) + ((ep_addr & USB_DIR_IN) ? 16 : 0));
> +}
> +
> +static int cdns3_get_dma_pos(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + int dma_index;
> +
> + dma_index = readl(&priv_dev->regs->ep_traddr) - priv_ep->trb_pool_dma;
> +
> + return dma_index / TRB_SIZE;
> +}
> +
> +/**
> + * cdns3_next_request - returns next request from list
> + * @list: list containing requests
> + *
> + * Returns request or NULL if no requests in list
> + */
> +struct usb_request *cdns3_next_request(struct list_head *list)

Maybe direct get cdns3_request, seems more often you need cdns3_request.

> +{
> + return list_first_entry_or_null(list, struct usb_request, list);
> +}
> +
> +/**
> + * cdns3_next_align_buf - returns next buffer from list
> + * @list: list containing buffers
> + *
> + * Returns buffer or NULL if no buffers in list
> + */
> +struct cdns3_aligned_buf *cdns3_next_align_buf(struct list_head *list)
> +{
> + return list_first_entry_or_null(list, struct cdns3_aligned_buf, list);
> +}
> +
> +/**
> + * select_ep - selects endpoint
> + * @priv_dev: extended gadget object
> + * @ep: endpoint address
> + */
> +void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep)
> +{
> + if (priv_dev->selected_ep == ep)
> + return;
> +
> + priv_dev->selected_ep = ep;
> + writel(ep, &priv_dev->regs->ep_sel);
> +}
> +
> +dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *trb)
> +{
> + u32 offset = (char *)trb - (char *)priv_ep->trb_pool;
> +
> + return priv_ep->trb_pool_dma + offset;
> +}
> +
> +int cdns3_ring_size(struct cdns3_endpoint *priv_ep)
> +{
> + switch (priv_ep->type) {
> + case USB_ENDPOINT_XFER_ISOC:
> + return TRB_ISO_RING_SIZE;
> + case USB_ENDPOINT_XFER_CONTROL:
> + return TRB_CTRL_RING_SIZE;
> + default:
> + return TRB_RING_SIZE;
> + }
> +}
> +
> +/**
> + * cdns3_allocate_trb_pool - Allocates TRB's pool for selected endpoint
> + * @priv_ep: endpoint object
> + *
> + * Function will return 0 on success or -ENOMEM on allocation error
> + */
> +int cdns3_allocate_trb_pool(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + int ring_size = cdns3_ring_size(priv_ep);
> + struct cdns3_trb *link_trb;
> +
> + if (!priv_ep->trb_pool) {
> + priv_ep->trb_pool = dma_alloc_coherent(priv_dev->sysdev,
> + ring_size,
> + &priv_ep->trb_pool_dma,
> + GFP_DMA32 | GFP_ATOMIC);
> + if (!priv_ep->trb_pool)
> + return -ENOMEM;
> + } else {
> + memset(priv_ep->trb_pool, 0, ring_size);
> + }
> +
> + if (!priv_ep->num)
> + return 0;
> +
> + priv_ep->num_trbs = ring_size / TRB_SIZE;
> + /* Initialize the last TRB as Link TRB */
> + link_trb = (priv_ep->trb_pool + (priv_ep->num_trbs - 1));
> + link_trb->buffer = TRB_BUFFER(priv_ep->trb_pool_dma);
> + link_trb->control = TRB_CYCLE | TRB_TYPE(TRB_LINK) | TRB_TOGGLE;
> +
> + return 0;
> +}
> +
> +static void cdns3_free_trb_pool(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + if (priv_ep->trb_pool) {
> + dma_free_coherent(priv_dev->sysdev,
> + cdns3_ring_size(priv_ep),
> + priv_ep->trb_pool, priv_ep->trb_pool_dma);
> + priv_ep->trb_pool = NULL;
> + }
> +}
> +
> +/**
> + * cdns3_ep_stall_flush - Stalls and flushes selected endpoint
> + * @priv_ep: endpoint object
> + *
> + * Endpoint must be selected before call to this function
> + */
> +static void cdns3_ep_stall_flush(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + cdns3_dbg(priv_ep->cdns3_dev, "Stall & flush endpoint %s\n",
> + priv_ep->name);
> +
> + writel(EP_CMD_DFLUSH | EP_CMD_ERDY | EP_CMD_SSTALL,
> + &priv_dev->regs->ep_cmd);
> +
> + /* wait for DFLUSH cleared */
> + cdns3_handshake(&priv_dev->regs->ep_cmd, EP_CMD_DFLUSH, 0, 1000);
> + priv_ep->flags |= EP_STALL;
> +}
> +
> +/**
> + * cdns3_hw_reset_eps_config - reset endpoints configuration kept by controller.
> + * @priv_dev: extended gadget object
> + */
> +void cdns3_hw_reset_eps_config(struct cdns3_device *priv_dev)
> +{
> + writel(USB_CONF_CFGRST, &priv_dev->regs->usb_conf);
> +
> + cdns3_allow_enable_l1(priv_dev, 0);
> + priv_dev->hw_configured_flag = 0;
> + priv_dev->onchip_mem_allocated_size = 0;
> + priv_dev->out_mem_is_allocated = 0;
> + priv_dev->wait_for_setup = 0;
> +}
> +
> +/**
> + * cdns3_ep_inc_trb - increment a trb index.
> + * @index: Pointer to the TRB index to increment.
> + * @cs: Cycle state
> + * @trb_in_seg: number of TRBs in segment
> + *
> + * The index should never point to the link TRB. After incrementing,
> + * if it is point to the link TRB, wrap around to the beginning and revert
> + * cycle state bit The
> + * link TRB is always at the last TRB entry.
> + */
> +static void cdns3_ep_inc_trb(int *index, u8 *cs, int trb_in_seg)
> +{
> + (*index)++;
> + if (*index == (trb_in_seg - 1)) {
> + *index = 0;
> + *cs ^= 1;
> + }
> +}
> +
> +/**
> + * cdns3_ep_inc_enq - increment endpoint's enqueue pointer
> + * @priv_ep: The endpoint whose enqueue pointer we're incrementing
> + */
> +static void cdns3_ep_inc_enq(struct cdns3_endpoint *priv_ep)
> +{
> + priv_ep->free_trbs--;
> + cdns3_ep_inc_trb(&priv_ep->enqueue, &priv_ep->pcs, priv_ep->num_trbs);
> +}
> +
> +/**
> + * cdns3_ep_inc_deq - increment endpoint's dequeue pointer
> + * @priv_ep: The endpoint whose dequeue pointer we're incrementing
> + */
> +static void cdns3_ep_inc_deq(struct cdns3_endpoint *priv_ep)
> +{
> + priv_ep->free_trbs++;
> + cdns3_ep_inc_trb(&priv_ep->dequeue, &priv_ep->ccs, priv_ep->num_trbs);
> +}
> +
> +void cdns3_move_deq_to_next_trb(struct cdns3_request *priv_req)
> +{
> + struct cdns3_endpoint *priv_ep = priv_req->priv_ep;
> + int current_trb = priv_req->start_trb;
> +
> + while (current_trb != priv_req->end_trb) {
> + cdns3_ep_inc_deq(priv_ep);
> + current_trb = priv_ep->dequeue;
> + }
> +
> + cdns3_ep_inc_deq(priv_ep);
> +}
> +
> +/**
> + * cdns3_allow_enable_l1 - enable/disable permits to transition to L1.
> + * @priv_dev: Extended gadget object
> + * @enable: Enable/disable permit to transition to L1.
> + *
> + * If bit USB_CONF_L1EN is set and device receive Extended Token packet,
> + * then controller answer with ACK handshake.
> + * If bit USB_CONF_L1DS is set and device receive Extended Token packet,
> + * then controller answer with NYET handshake.
> + */
> +void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable)
> +{
> + if (enable)
> + writel(USB_CONF_L1EN, &priv_dev->regs->usb_conf);
> + else
> + writel(USB_CONF_L1DS, &priv_dev->regs->usb_conf);
> +}
> +
> +enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev)
> +{
> + u32 reg;
> +
> + reg = readl(&priv_dev->regs->usb_sts);
> +
> + if (DEV_SUPERSPEED(reg))
> + return USB_SPEED_SUPER;
> + else if (DEV_HIGHSPEED(reg))
> + return USB_SPEED_HIGH;
> + else if (DEV_FULLSPEED(reg))
> + return USB_SPEED_FULL;
> + else if (DEV_LOWSPEED(reg))
> + return USB_SPEED_LOW;
> + return USB_SPEED_UNKNOWN;
> +}
> +
> +/**
> + * cdns3_start_all_request - add to ring all request not started
> + * @priv_dev: Extended gadget object
> + * @priv_ep: The endpoint for whom request will be started.
> + *
> + * Returns return ENOMEM if transfer ring i not enough TRBs to start
> + * all requests.
> + */
> +static int cdns3_start_all_request(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_request *priv_req;
> + struct usb_request *request;
> + int ret = 0;
> +
> + while (!list_empty(&priv_ep->deferred_req_list)) {
> + request = cdns3_next_request(&priv_ep->deferred_req_list);
> + priv_req = to_cdns3_request(request);
> +
> + ret = cdns3_ep_run_transfer(priv_ep, request);
> + if (ret)
> + return ret;
> +
> + list_del(&request->list);
> + list_add_tail(&request->list,
> + &priv_ep->pending_req_list);
> + }
> +
> + priv_ep->flags &= ~EP_RING_FULL;
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_giveback - call struct usb_request's ->complete callback
> + * @priv_ep: The endpoint to whom the request belongs to
> + * @priv_req: The request we're giving back
> + * @status: completion code for the request
> + *
> + * Must be called with controller's lock held and interrupts disabled. This
> + * function will unmap @req and call its ->complete() callback to notify upper
> + * layers that it has completed.
> + */
> +void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req,
> + int status)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct usb_request *request = &priv_req->request;
> +
> + list_del_init(&request->list);
> +
> + if (request->status == -EINPROGRESS)
> + request->status = status;
> +
> + usb_gadget_unmap_request_by_dev(priv_dev->sysdev, request,
> + priv_ep->dir);
> +
> + if ((priv_req->flags & REQUEST_UNALIGNED) &&
> + priv_ep->dir == USB_DIR_OUT && !request->status)
> + memcpy(request->buf, priv_req->aligned_buf->buf,
> + request->length);
> +
> + priv_req->flags &= ~(REQUEST_PENDING | REQUEST_UNALIGNED);
> + trace_cdns3_gadget_giveback(priv_req);
> +
> + if (request->complete) {
> + spin_unlock(&priv_dev->lock);
> + usb_gadget_giveback_request(&priv_ep->endpoint,
> + request);
> + spin_lock(&priv_dev->lock);
> + }
> +
> + if (request->buf == priv_dev->zlp_buf)
> + cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
> +}
> +
> +void cdns3_wa1_restore_cycle_bit(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + /* Work around for stale data address in TRB*/
> + if (priv_ep->wa1_set) {
> + cdns3_dbg(priv_dev, "WA1: update cycle bit\n");
> + priv_ep->wa1_set = 0;
> + priv_ep->wa1_trb_index = 0xFFFF;
> + if (priv_ep->wa1_cycle_bit) {
> + priv_ep->wa1_trb->control =
> + priv_ep->wa1_trb->control | 0x1;
> + } else {
> + priv_ep->wa1_trb->control =
> + priv_ep->wa1_trb->control & ~0x1;
> + }
> + }
> +}
> +
> +static int cdns3_prepare_aligned_request_buf(struct cdns3_request *priv_req)
> +{
> + struct cdns3_endpoint *priv_ep = priv_req->priv_ep;
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_aligned_buf *buf;
> +
> + /* check if buffer is aligned to 8. */
> + if (!((uintptr_t)priv_req->request.buf & 0x7))
> + return 0;
> +
> + buf = priv_req->aligned_buf;
> +
> + if (!buf || priv_req->request.length > buf->size) {
> + buf = kzalloc(sizeof(*buf), GFP_ATOMIC);
> + if (!buf)
> + return -ENOMEM;
> +
> + buf->size = priv_req->request.length;
> +
> + buf->buf = dma_alloc_coherent(priv_dev->sysdev,
> + buf->size,
> + &buf->dma,
> + GFP_ATOMIC);
> + if (!buf->buf) {
> + kfree(buf);
> + return -ENOMEM;
> + }
> +
> + if (priv_req->aligned_buf) {
> + trace_cdns3_free_aligned_request(priv_req);
> + priv_req->aligned_buf->in_use = 0;
> + priv_dev->run_garbage_colector = 1;
> + }
> +
> + buf->in_use = 1;
> + priv_req->aligned_buf = buf;
> +
> + list_add_tail(&buf->list,
> + &priv_dev->aligned_buf_list);
> + }
> +
> + if (priv_ep->dir == USB_DIR_IN) {
> + memcpy(buf->buf, priv_req->request.buf,
> + priv_req->request.length);
> + }
> +
> + priv_req->flags |= REQUEST_UNALIGNED;
> + trace_cdns3_prepare_aligned_request(priv_req);
> +
> + return 0;
> +}
> +
> +static int cdns3_wa1_update_guard(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *trb)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + if (!priv_ep->wa1_set) {
> + u32 doorbell;
> +
> + doorbell = !!(readl(&priv_dev->regs->ep_cmd) & EP_CMD_DRDY);
> +
> + if (doorbell) {
> + priv_ep->wa1_cycle_bit = priv_ep->pcs ? TRB_CYCLE : 0;
> + priv_ep->wa1_set = 1;
> + priv_ep->wa1_trb = trb;
> + priv_ep->wa1_trb_index = priv_ep->enqueue;
> + cdns3_dbg(priv_dev, "WA1 set guard\n");
> + return 0;
> + }
> + }
> + return 1;
> +}
> +
> +static void cdns3_wa1_tray_restore_cycle_bit(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + int dma_index;
> + u32 doorbell;
> +
> + doorbell = !!(readl(&priv_dev->regs->ep_cmd) & EP_CMD_DRDY);
> + dma_index = cdns3_get_dma_pos(priv_dev, priv_ep);
> +
> + if (!doorbell || dma_index != priv_ep->wa1_trb_index)
> + cdns3_wa1_restore_cycle_bit(priv_ep);
> +}
> +
> +/**
> + * cdns3_ep_run_transfer - start transfer on no-default endpoint hardware
> + * @priv_ep: endpoint object
> + *
> + * Returns zero on success or negative value on failure
> + */
> +int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
> + struct usb_request *request)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_request *priv_req;
> + struct cdns3_trb *trb;
> + dma_addr_t trb_dma;
> + u32 togle_pcs = 1;
> + int sg_iter = 0;
> + int num_trb;
> + int address;
> + u32 control;
> + int pcs;
> +
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC)
> + num_trb = priv_ep->interval;
> + else
> + num_trb = request->num_sgs ? request->num_sgs : 1;
> +
> + if (num_trb > priv_ep->free_trbs) {
> + priv_ep->flags |= EP_RING_FULL;
> + return -ENOBUFS;
> + }
> +
> + priv_req = to_cdns3_request(request);
> + address = priv_ep->endpoint.desc->bEndpointAddress;
> +
> + priv_ep->flags |= EP_PENDING_REQUEST;
> +
> + /* must allocate buffer aligned to 8 */
> + if (priv_req->flags & REQUEST_UNALIGNED)
> + trb_dma = priv_req->aligned_buf->dma;
> + else
> + trb_dma = request->dma;
> +
> + trb = priv_ep->trb_pool + priv_ep->enqueue;
> + priv_req->start_trb = priv_ep->enqueue;
> + priv_req->trb = trb;
> +
> + cdns3_select_ep(priv_ep->cdns3_dev, address);
> +
> + /* prepare ring */
> + if ((priv_ep->enqueue + num_trb) >= (priv_ep->num_trbs - 1)) {
> + struct cdns3_trb *link_trb;
> + int doorbell, dma_index;
> + u32 ch_bit = 0;
> +
> + doorbell = !!(readl(&priv_dev->regs->ep_cmd) & EP_CMD_DRDY);
> + dma_index = cdns3_get_dma_pos(priv_dev, priv_ep);
> +
> + /* Driver can't update LINK TRB if it is current processed. */
> + if (doorbell && dma_index == priv_ep->num_trbs - 1) {
> + priv_ep->flags |= EP_DEFERRED_DRDY;
> + return -ENOBUFS;
> + }
> +
> + /*updating C bt in Link TRB before starting DMA*/
> + link_trb = priv_ep->trb_pool + (priv_ep->num_trbs - 1);
> + /*
> + * For TRs size equal 2 enabling TRB_CHAIN for epXin causes
> + * that DMA stuck at the LINK TRB.
> + * On the other hand, removing TRB_CHAIN for longer TRs for
> + * epXout cause that DMA stuck after handling LINK TRB.
> + * To eliminate this strange behavioral driver set TRB_CHAIN
> + * bit only for TR size > 2.
> + */
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC ||
> + TRBS_PER_SEGMENT > 2)
> + ch_bit = TRB_CHAIN;
> +
> + link_trb->control = ((priv_ep->pcs) ? TRB_CYCLE : 0) |
> + TRB_TYPE(TRB_LINK) | TRB_TOGGLE | ch_bit;
> + }
> +
> + if (priv_dev->dev_ver <= DEV_VER_V2)
> + togle_pcs = cdns3_wa1_update_guard(priv_ep, trb);
> +
> + /* set incorrect Cycle Bit for first trb*/
> + control = priv_ep->pcs ? 0 : TRB_CYCLE;
> +
> + do {
> + u32 length;
> + u16 td_size = 0;
> +
> + /* fill TRB */
> + control |= TRB_TYPE(TRB_NORMAL);
> + trb->buffer = TRB_BUFFER(request->num_sgs == 0
> + ? trb_dma : request->sg[sg_iter].dma_address);
> +
> + if (likely(!request->num_sgs))
> + length = request->length;
> + else
> + length = request->sg[sg_iter].length;
> +
> + if (likely(priv_dev->dev_ver >= DEV_VER_V2))
> + td_size = DIV_ROUND_UP(length,
> + priv_ep->endpoint.maxpacket);
> +
> + trb->length = TRB_BURST_LEN(priv_ep->trb_burst_size) |
> + TRB_LEN(length);
> + if (priv_dev->gadget.speed == USB_SPEED_SUPER)
> + trb->length |= TRB_TDL_SS_SIZE(td_size);
> + else
> + control |= TRB_TDL_HS_SIZE(td_size);
> +
> + pcs = priv_ep->pcs ? TRB_CYCLE : 0;
> +
> + /*
> + * first trb should be prepared as last to avoid processing
> + * transfer to early
> + */
> + if (sg_iter != 0)
> + control |= pcs;
> +
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && !priv_ep->dir) {
> + control |= TRB_IOC | TRB_ISP;
> + } else {
> + /* for last element in TD or in SG list */
> + if (sg_iter == (num_trb - 1) && sg_iter != 0)
> + control |= pcs | TRB_IOC | TRB_ISP;
> + }
> +
> + if (sg_iter)
> + trb->control = control;
> + else
> + priv_req->trb->control = control;
> +
> + control = 0;
> + ++sg_iter;
> + priv_req->end_trb = priv_ep->enqueue;
> + cdns3_ep_inc_enq(priv_ep);
> + trb = priv_ep->trb_pool + priv_ep->enqueue;
> + } while (sg_iter < num_trb);
> +
> + trb = priv_req->trb;
> +
> + priv_req->flags |= REQUEST_PENDING;
> +
> + if (sg_iter == 1)
> + trb->control |= TRB_IOC | TRB_ISP;
> + /*
> + * Memory barrier - cycle bit must be set before other filds in trb.
> + */
> + wmb();
> +
> + /* give the TD to the consumer*/
> + if (togle_pcs)
> + trb->control = trb->control ^ 1;
> +
> + if (priv_dev->dev_ver <= DEV_VER_V2)
> + cdns3_wa1_tray_restore_cycle_bit(priv_dev, priv_ep);
> +
> + trace_cdns3_prepare_trb(priv_ep, priv_req->trb);
> +
> + /*
> + * Memory barrier - Cycle Bit must be set before trb->length and
> + * trb->buffer fields.
> + */
> + wmb();
> +
> + /*
> + * For DMULT mode we can set address to transfer ring only once after
> + * enabling endpoint.
> + */
> + if (priv_ep->flags & EP_UPDATE_EP_TRBADDR) {
> + /*
> + * Until SW is not ready to handle the OUT transfer the ISO OUT
> + * Endpoint should be disabled (EP_CFG.ENABLE = 0).
> + * EP_CFG_ENABLE must be set before updating ep_traddr.
> + */
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && !priv_ep->dir &&
> + !(priv_ep->flags & EP_QUIRK_ISO_OUT_EN)) {
> + priv_ep->flags |= EP_QUIRK_ISO_OUT_EN;
> + cdns3_set_register_bit(&priv_dev->regs->ep_cfg,
> + EP_CFG_ENABLE);
> + }
> +
> + writel(EP_TRADDR_TRADDR(priv_ep->trb_pool_dma +
> + priv_req->start_trb * TRB_SIZE),
> + &priv_dev->regs->ep_traddr);
> +
> + cdns3_dbg(priv_ep->cdns3_dev, "Update ep_trbaddr for %s to %08x\n",
> + priv_ep->name, readl(&priv_dev->regs->ep_traddr));
> +
> + priv_ep->flags &= ~EP_UPDATE_EP_TRBADDR;
> + }
> +
> + /* WORKAROUND for transition to L0 */
> + __cdns3_gadget_wakeup(priv_dev);
> +
> + if (!priv_ep->wa1_set && !(priv_ep->flags & EP_STALL)) {
> + trace_cdns3_ring(priv_ep);
> + /*clearing TRBERR and EP_STS_DESCMIS before seting DRDY*/
> + writel(EP_STS_TRBERR | EP_STS_DESCMIS, &priv_dev->regs->ep_sts);
> + writel(EP_CMD_DRDY, &priv_dev->regs->ep_cmd);
> + trace_cdns3_doorbell_epx(priv_ep->name,
> + readl(&priv_dev->regs->ep_traddr));
> + }
> +
> + return 0;
> +}
> +
> +void cdns3_set_hw_configuration(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct usb_ep *ep;
> + int result = 0;
> +
> + if (priv_dev->hw_configured_flag)
> + return;
> +
> + writel(USB_CONF_CFGSET, &priv_dev->regs->usb_conf);
> + writel(EP_CMD_ERDY | EP_CMD_REQ_CMPL, &priv_dev->regs->ep_cmd);
> +
> + cdns3_set_register_bit(&priv_dev->regs->usb_conf,
> + USB_CONF_U1EN | USB_CONF_U2EN);
> +
> + /* wait until configuration set */
> + result = cdns3_handshake(&priv_dev->regs->usb_sts,
> + USB_STS_CFGSTS_MASK, 1, 100);
> +
> + priv_dev->hw_configured_flag = 1;
> + cdns3_allow_enable_l1(priv_dev, 1);
> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + if (ep->enabled) {
> + priv_ep = ep_to_cdns3_ep(ep);
> + cdns3_start_all_request(priv_dev, priv_ep);
> + }
> + }
> +}
> +
> +/**
> + * cdns3_request_handled - check whether request has been handled by DMA
> + *
> + * @priv_ep: extended endpoint object.
> + * @priv_req: request object for checking
> + *
> + * Endpoint must be selected before invoking this function.
> + *
> + * Returns false if request has not been handled by DMA, else returns true.
> + *
> + * SR - start ring
> + * ER - end ring
> + * DQ = priv_ep->dequeue - dequeue position
> + * EQ = priv_ep->enqueue - enqueue position
> + * ST = priv_req->start_trb - index of first TRB in transfer ring
> + * ET = priv_req->end_trb - index of last TRB in transfer ring
> + * CI = current_index - index of processed TRB by DMA.
> + *
> + * As first step, function checks if cycle bit for priv_req->start_trb is
> + * correct.
> + *
> + * some rules:
> + * 1. priv_ep->dequeue never exceed current_index.
> + * 2 priv_ep->enqueue never exceed priv_ep->dequeue
> + * 3. exception: priv_ep->enqueue == priv_ep->dequeue
> + * and priv_ep->free_trbs is zero.
> + * This case indicate that TR is full.
> + *
> + * Then We can split recognition into two parts:
> + * Case 1 - priv_ep->dequeue < current_index
> + * SR ... EQ ... DQ ... CI ... ER
> + * SR ... DQ ... CI ... EQ ... ER
> + *
> + * Request has been handled by DMA if ST and ET is between DQ and CI.
> + *
> + * Case 2 - priv_ep->dequeue > current_index
> + * This situation take place when CI go through the LINK TRB at the end of
> + * transfer ring.
> + * SR ... CI ... EQ ... DQ ... ER
> + *
> + * Request has been handled by DMA if ET is less then CI or
> + * ET is greater or equal DQ.
> + */
> +static bool cdns3_request_handled(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_trb *trb = priv_req->trb;
> + int current_index = 0;
> + int handled = 0;
> + int doorbell;
> +
> + current_index = cdns3_get_dma_pos(priv_dev, priv_ep);
> + doorbell = !!(readl(&priv_dev->regs->ep_cmd) & EP_CMD_DRDY);
> +
> + trb = &priv_ep->trb_pool[priv_req->start_trb];
> +
> + if ((trb->control & TRB_CYCLE) != priv_ep->ccs)
> + goto finish;
> +
> + if (doorbell == 1 && current_index == priv_ep->dequeue)
> + goto finish;
> +
> + /* The corner case for TRBS_PER_SEGMENT equal 2). */
> + if (TRBS_PER_SEGMENT == 2 && priv_ep->type != USB_ENDPOINT_XFER_ISOC) {
> + handled = 1;
> + goto finish;
> + }
> +
> + if (priv_ep->enqueue == priv_ep->dequeue &&
> + priv_ep->free_trbs == 0) {
> + handled = 1;
> + } else if (priv_ep->dequeue < current_index) {
> + if ((current_index == (priv_ep->num_trbs - 1)) &&
> + !priv_ep->dequeue)
> + goto finish;
> +
> + if (priv_req->end_trb >= priv_ep->dequeue &&
> + priv_req->end_trb < current_index)
> + handled = 1;
> + } else if (priv_ep->dequeue > current_index) {
> + if (priv_req->end_trb < current_index ||
> + priv_req->end_trb >= priv_ep->dequeue)
> + handled = 1;
> + }
> +
> +finish:
> + trace_cdns3_request_handled(priv_req, current_index, handled);
> +
> + return handled;
> +}
> +
> +static void cdns3_transfer_completed(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_request *priv_req;
> + struct usb_request *request;
> + struct cdns3_trb *trb;
> +
> + while (!list_empty(&priv_ep->pending_req_list)) {
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> + priv_req = to_cdns3_request(request);
> +
> + /* Re-select endpoint. It could be changed by other CPU during
> + * handling usb_gadget_giveback_request.
> + */
> + cdns3_select_ep(priv_dev, priv_ep->endpoint.address);
> +
> + if (!cdns3_request_handled(priv_ep, priv_req))
> + goto prepare_next_td;
> +
> + trb = priv_ep->trb_pool + priv_ep->dequeue;
> + trace_cdns3_complete_trb(priv_ep, trb);
> +
> + if (trb != priv_req->trb)
> + dev_warn(priv_dev->dev,
> + "request_trb=0x%p, queue_trb=0x%p\n",
> + priv_req->trb, trb);
> +
> + request->actual = TRB_LEN(le32_to_cpu(trb->length));
> + cdns3_move_deq_to_next_trb(priv_req);
> + cdns3_gadget_giveback(priv_ep, priv_req, 0);
> +
> + if (priv_ep->type != USB_ENDPOINT_XFER_ISOC &&
> + TRBS_PER_SEGMENT == 2)
> + break;
> + }
> + priv_ep->flags &= ~EP_PENDING_REQUEST;
> +
> +prepare_next_td:
> + cdns3_start_all_request(priv_dev, priv_ep);
> +}
> +
> +void cdns3_rearm_transfer(struct cdns3_endpoint *priv_ep, u8 rearm)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> +
> + cdns3_wa1_restore_cycle_bit(priv_ep);
> +
> + if (rearm) {
> + trace_cdns3_ring(priv_ep);
> +
> + /* Cycle Bit must be updated before arming DMA. */
> + wmb();
> + writel(EP_CMD_DRDY, &priv_dev->regs->ep_cmd);
> +
> + trace_cdns3_doorbell_epx(priv_ep->name,
> + readl(&priv_dev->regs->ep_traddr));
> + }
> +}
> +
> +/**
> + * cdns3_check_ep_interrupt_proceed - Processes interrupt related to endpoint
> + * @priv_ep: endpoint object
> + *
> + * Returns 0
> + */
> +static int cdns3_check_ep_interrupt_proceed(struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + u32 ep_sts_reg;
> +
> + cdns3_select_ep(priv_dev, priv_ep->endpoint.address);
> +
> + trace_cdns3_epx_irq(priv_dev, priv_ep);
> +
> + ep_sts_reg = readl(&priv_dev->regs->ep_sts);
> + writel(ep_sts_reg, &priv_dev->regs->ep_sts);
> +
> + if (ep_sts_reg & EP_STS_TRBERR) {
> + /*
> + * For isochronous transfer driver completes request on
> + * IOC or on TRBERR. IOC appears only when device receive
> + * OUT data packet. If host disable stream or lost some packet
> + * then the only way to finish all queued transfer is to do it
> + * on TRBERR event.
> + */
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC &&
> + !priv_ep->wa1_set) {
> + if (!priv_ep->dir) {
> + u32 ep_cfg = readl(&priv_dev->regs->ep_cfg);
> +
> + ep_cfg &= ~EP_CFG_ENABLE;
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> + priv_ep->flags &= ~EP_QUIRK_ISO_OUT_EN;
> + }
> + cdns3_transfer_completed(priv_dev, priv_ep);
> + } else {
> + if (priv_ep->flags & EP_DEFERRED_DRDY) {
> + priv_ep->flags &= ~EP_DEFERRED_DRDY;
> + cdns3_start_all_request(priv_dev, priv_ep);
> + } else {
> + cdns3_rearm_transfer(priv_ep, priv_ep->wa1_set);
> + }
> + }
> + }
> +
> + if ((ep_sts_reg & EP_STS_IOC) || (ep_sts_reg & EP_STS_ISP))
> + cdns3_transfer_completed(priv_dev, priv_ep);
> +
> + return 0;
> +}
> +
> +/**
> + * cdns3_check_usb_interrupt_proceed - Processes interrupt related to device
> + * @priv_dev: extended gadget object
> + * @usb_ists: bitmap representation of device's reported interrupts
> + * (usb_ists register value)
> + */
> +static void cdns3_check_usb_interrupt_proceed(struct cdns3_device *priv_dev,
> + u32 usb_ists)
> +{
> + int speed = 0;
> +
> + trace_cdns3_usb_irq(priv_dev, usb_ists);
> + if (usb_ists & USB_ISTS_L1ENTI) {
> + /*
> + * WORKAROUND: CDNS3 controller has issue with hardware resuming
> + * from L1. To fix it, if any DMA transfer is pending driver
> + * must starts driving resume signal immediately.
> + */
> + if (readl(&priv_dev->regs->drbl))
> + __cdns3_gadget_wakeup(priv_dev);
> + }
> +
> + /* Connection detected */
> + if (usb_ists & (USB_ISTS_CON2I | USB_ISTS_CONI)) {
> + speed = cdns3_get_speed(priv_dev);
> + priv_dev->gadget.speed = speed;
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_POWERED);
> + cdns3_ep0_config(priv_dev);
> + }
> +
> + /* Disconnection detected */
> + if (usb_ists & (USB_ISTS_DIS2I | USB_ISTS_DISI)) {
> + if (priv_dev->gadget_driver &&
> + priv_dev->gadget_driver->disconnect) {
> + spin_unlock(&priv_dev->lock);
> + priv_dev->gadget_driver->disconnect(&priv_dev->gadget);
> + spin_lock(&priv_dev->lock);
> + }
> +
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> + usb_gadget_set_state(&priv_dev->gadget, USB_STATE_NOTATTACHED);
> + cdns3_hw_reset_eps_config(priv_dev);
> + }
> +
> + if (usb_ists & (USB_ISTS_L2ENTI | USB_ISTS_U3ENTI)) {
> + if (priv_dev->gadget_driver &&
> + priv_dev->gadget_driver->suspend) {
> + spin_unlock(&priv_dev->lock);
> + priv_dev->gadget_driver->suspend(&priv_dev->gadget);
> + spin_lock(&priv_dev->lock);
> + }
> + }
> +
> + if (usb_ists & (USB_ISTS_L2EXTI | USB_ISTS_U3EXTI)) {
> + if (priv_dev->gadget_driver &&
> + priv_dev->gadget_driver->resume) {
> + spin_unlock(&priv_dev->lock);
> + priv_dev->gadget_driver->resume(&priv_dev->gadget);
> + spin_lock(&priv_dev->lock);
> + }
> + }
> +
> + /* reset*/
> + if (usb_ists & (USB_ISTS_UWRESI | USB_ISTS_UHRESI | USB_ISTS_U2RESI)) {
> + if (priv_dev->gadget_driver) {
> + spin_unlock(&priv_dev->lock);
> + usb_gadget_udc_reset(&priv_dev->gadget,
> + priv_dev->gadget_driver);
> + spin_lock(&priv_dev->lock);
> +
> + /*read again to check the actual speed*/
> + speed = cdns3_get_speed(priv_dev);
> + priv_dev->gadget.speed = speed;
> + cdns3_hw_reset_eps_config(priv_dev);
> + cdns3_ep0_config(priv_dev);
> + }
> + }
> +}
> +
> +/**
> + * cdns3_device_irq_handler- interrupt handler for device part of controller
> + *
> + * @irq: irq number for cdns3 core device
> + * @data: structure of cdns3
> + *
> + * Returns IRQ_HANDLED or IRQ_NONE
> + */
> +static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
> +{
> + struct cdns3_device *priv_dev;
> + struct cdns3 *cdns = data;
> + irqreturn_t ret = IRQ_NONE;
> + unsigned long flags;
> + u32 reg;
> +
> + priv_dev = cdns->gadget_dev;
> + spin_lock_irqsave(&priv_dev->lock, flags);

spin_lock()

> +
> + /* check USB device interrupt */
> + reg = readl(&priv_dev->regs->usb_ists);
> +
> + if (reg) {
> + writel(reg, &priv_dev->regs->usb_ists);
> + cdns3_check_usb_interrupt_proceed(priv_dev, reg);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check endpoint interrupt */
> + reg = readl(&priv_dev->regs->ep_ists);
> +
> + if (reg) {
> + priv_dev->shadow_ep_en |= reg;
> + reg = ~reg & readl(&priv_dev->regs->ep_ien);
> + /* mask deferred interrupt. */
> + writel(reg, &priv_dev->regs->ep_ien);
> + ret = IRQ_WAKE_THREAD;
> + }
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_device_thread_irq_handler- interrupt handler for device part
> + * of controller
> + *
> + * @irq: irq number for cdns3 core device
> + * @data: structure of cdns3
> + *
> + * Returns IRQ_HANDLED or IRQ_NONE
> + */
> +static irqreturn_t cdns3_device_thread_irq_handler(int irq, void *data)
> +{
> + struct cdns3_device *priv_dev;
> + struct cdns3 *cdns = data;
> + irqreturn_t ret = IRQ_NONE;
> + unsigned long flags;
> + u32 ep_ien;
> + int bit;
> + u32 reg;
> +
> + priv_dev = cdns->gadget_dev;
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + reg = readl(&priv_dev->regs->ep_ists);
> +
> + /* handle default endpoint OUT */
> + if (reg & EP_ISTS_EP_OUT0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_OUT);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* handle default endpoint IN */
> + if (reg & EP_ISTS_EP_IN0) {
> + cdns3_check_ep0_interrupt_proceed(priv_dev, USB_DIR_IN);
> + ret = IRQ_HANDLED;
> + }
> +
> + /* check if interrupt from non default endpoint, if no exit */
> + reg &= ~(EP_ISTS_EP_OUT0 | EP_ISTS_EP_IN0);
> + if (!reg)
> + goto irqend;
> +
> + for_each_set_bit(bit, (unsigned long *)&reg,
> + sizeof(u32) * BITS_PER_BYTE) {
> + priv_dev->shadow_ep_en |= BIT(bit);
> + cdns3_check_ep_interrupt_proceed(priv_dev->eps[bit]);
> + ret = IRQ_HANDLED;
> + }
> +
> + if (priv_dev->run_garbage_colector) {
> + struct cdns3_aligned_buf *buf, *tmp;
> +
> + list_for_each_entry_safe(buf, tmp, &priv_dev->aligned_buf_list,
> + list) {
> + if (!buf->in_use) {
> + list_del(&buf->list);
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + dma_free_coherent(priv_dev->sysdev, buf->size,
> + buf->buf,
> + buf->dma);
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + kfree(buf);
> + }
> + }
> +
> + priv_dev->run_garbage_colector = 0;
> + }
> +
> +irqend:
> + ep_ien = readl(&priv_dev->regs->ep_ien) | priv_dev->shadow_ep_en;
> + priv_dev->shadow_ep_en = 0;
> + /* Unmask all handled EP interrupts */
> + writel(ep_ien, &priv_dev->regs->ep_ien);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_ep_onchip_buffer_reserve - Try to reserve onchip buf for EP
> + *
> + * The real reservation will occur during write to EP_CFG register,
> + * this function is used to check if the 'size' reservation is allowed.
> + *
> + * @priv_dev: extended gadget object
> + * @size: the size (KB) for EP would like to allocate
> + * @is_in: endpoint direction
> + *
> + * Return 0 if the required size can met or negative value on failure
> + */
> +static int cdns3_ep_onchip_buffer_reserve(struct cdns3_device *priv_dev,
> + int size, int is_in)
> +{
> + u32 onchip_mem;
> +
> + if (is_in) {
> + priv_dev->onchip_mem_allocated_size += size;
> + } else {
> + /* ALL OUT EPs are shared the same chunk onchip memory */
> + if (size > priv_dev->out_mem_is_allocated) {
> + priv_dev->onchip_mem_allocated_size -= priv_dev->out_mem_is_allocated;
> + priv_dev->onchip_mem_allocated_size += size;
> + priv_dev->out_mem_is_allocated = size;
> + }
> + }
> +
> + onchip_mem = USB_CAP2_ACTUAL_MEM_SIZE(readl(&priv_dev->regs->usb_cap2));
> + if (!onchip_mem)
> + onchip_mem = 256;
> +
> + /* 2KB is reserved for EP0*/
> + onchip_mem -= 2;
> + if (priv_dev->onchip_mem_allocated_size > onchip_mem) {
> + priv_dev->onchip_mem_allocated_size -= size;
> + return -EPERM;
> + }
> +
> + return 0;
> +}
> +
> +void cdns3_configure_dmult(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> +
> + /* For dev_ver > DEV_VER_V2 DMULT is configured per endpoint */
> + if (priv_dev->dev_ver <= DEV_VER_V2)
> + writel(USB_CONF_DMULT, &regs->usb_conf);
> +
> + if (priv_dev->dev_ver == DEV_VER_V2)
> + writel(USB_CONF2_EN_TDL_TRB, &regs->usb_conf2);
> +
> + if (priv_dev->dev_ver >= DEV_VER_V3 && priv_ep) {
> + u32 mask;
> +
> + if (priv_ep->dir)
> + mask = BIT(priv_ep->num + 16);
> + else
> + mask = BIT(priv_ep->num);
> +
> + if (priv_ep->type != USB_ENDPOINT_XFER_ISOC) {
> + cdns3_set_register_bit(&regs->tdl_from_trb, mask);
> + cdns3_set_register_bit(&regs->tdl_beh, mask);
> + cdns3_set_register_bit(&regs->tdl_beh2, mask);
> + cdns3_set_register_bit(&regs->dma_adv_td, mask);
> + }
> +
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && !priv_ep->dir)
> + cdns3_set_register_bit(&regs->tdl_from_trb, mask);
> +
> + cdns3_set_register_bit(&regs->dtrans, mask);
> + }
> +}
> +
> +/**
> + * cdns3_ep_config Configure hardware endpoint
> + * @priv_ep: extended endpoint object
> + */
> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep)
> +{
> + bool is_iso_ep = (priv_ep->type == USB_ENDPOINT_XFER_ISOC);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + u32 bEndpointAddress = priv_ep->num | priv_ep->dir;
> + u32 max_packet_size = 0;
> + u8 maxburst = 0;
> + u32 ep_cfg = 0;
> + u8 buffering;
> + u8 mult = 0;
> + int ret;
> +
> + buffering = CDNS3_EP_BUF_SIZE - 1;
> +
> + cdns3_configure_dmult(priv_dev, priv_ep);
> +
> + switch (priv_ep->type) {
> + case USB_ENDPOINT_XFER_INT:
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_INT);
> +
> + if ((priv_dev->dev_ver == DEV_VER_V2 && !priv_ep->dir) ||
> + priv_dev->dev_ver > DEV_VER_V2)
> + ep_cfg |= EP_CFG_TDL_CHK;
> + break;
> + case USB_ENDPOINT_XFER_BULK:
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_BULK);
> +
> + if ((priv_dev->dev_ver == DEV_VER_V2 && !priv_ep->dir) ||
> + priv_dev->dev_ver > DEV_VER_V2)
> + ep_cfg |= EP_CFG_TDL_CHK;
> + break;
> + default:
> + ep_cfg = EP_CFG_EPTYPE(USB_ENDPOINT_XFER_ISOC);
> + mult = CDNS3_EP_ISO_HS_MULT - 1;
> + buffering = mult + 1;
> + }
> +
> + switch (priv_dev->gadget.speed) {
> + case USB_SPEED_FULL:
> + max_packet_size = is_iso_ep ? 1023 : 64;
> + break;
> + case USB_SPEED_HIGH:
> + max_packet_size = is_iso_ep ? 1024 : 512;
> + break;
> + case USB_SPEED_SUPER:
> + /* It's limitation that driver assumes in driver. */
> + mult = 0;
> + max_packet_size = 1024;
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC) {
> + maxburst = CDNS3_EP_ISO_SS_BURST - 1;
> + buffering = (mult + 1) *
> + (maxburst + 1);
> +
> + if (priv_ep->interval > 1)
> + buffering++;
> + } else {
> + maxburst = CDNS3_EP_BUF_SIZE - 1;
> + }
> + break;
> + default:
> + /* all other speed are not supported */
> + return;
> + }
> +
> + if (max_packet_size == 1024)
> + priv_ep->trb_burst_size = 128;
> + else if (max_packet_size >= 512)
> + priv_ep->trb_burst_size = 64;
> + else
> + priv_ep->trb_burst_size = 16;
> +
> + ret = cdns3_ep_onchip_buffer_reserve(priv_dev, buffering + 1,
> + !!priv_ep->dir);
> + if (ret) {
> + dev_err(priv_dev->dev, "onchip mem is full, ep is invalid\n");
> + return;
> + }
> +
> + ep_cfg |= EP_CFG_MAXPKTSIZE(max_packet_size) |
> + EP_CFG_MULT(mult) |
> + EP_CFG_BUFFERING(buffering) |
> + EP_CFG_MAXBURST(maxburst);
> +
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> +
> + dev_dbg(priv_dev->dev, "Configure %s: with val %08x\n",
> + priv_ep->name, ep_cfg);
> +}
> +
> +/* Find correct direction for HW endpoint according to description */
> +static int cdns3_ep_dir_is_correct(struct usb_endpoint_descriptor *desc,
> + struct cdns3_endpoint *priv_ep)
> +{
> + return (priv_ep->endpoint.caps.dir_in && usb_endpoint_dir_in(desc)) ||
> + (priv_ep->endpoint.caps.dir_out && usb_endpoint_dir_out(desc));
> +}
> +
> +static struct
> +cdns3_endpoint *cdns3_find_available_ep(struct cdns3_device *priv_dev,
> + struct usb_endpoint_descriptor *desc)
> +{
> + struct usb_ep *ep;
> + struct cdns3_endpoint *priv_ep;
> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + unsigned long num;
> + int ret;
> + /* ep name pattern likes epXin or epXout */
> + char c[2] = {ep->name[2], '\0'};
> +
> + ret = kstrtoul(c, 10, &num);
> + if (ret)
> + return ERR_PTR(ret);
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + if (cdns3_ep_dir_is_correct(desc, priv_ep)) {
> + if (!(priv_ep->flags & EP_CLAIMED)) {
> + priv_ep->num = num;
> + return priv_ep;
> + }
> + }
> + }
> +
> + return ERR_PTR(-ENOENT);
> +}
> +
> +/*
> + * Cadence IP has one limitation that all endpoints must be configured
> + * (Type & MaxPacketSize) before setting configuration through hardware
> + * register, it means we can't change endpoints configuration after
> + * set_configuration.
> + *
> + * This function set EP_CLAIMED flag which is added when the gadget driver
> + * uses usb_ep_autoconfig to configure specific endpoint;
> + * When the udc driver receives set_configurion request,
> + * it goes through all claimed endpoints, and configure all endpoints
> + * accordingly.
> + *
> + * At usb_ep_ops.enable/disable, we only enable and disable endpoint through
> + * ep_cfg register which can be changed after set_configuration, and do
> + * some software operation accordingly.
> + */
> +static struct
> +usb_ep *cdns3_gadget_match_ep(struct usb_gadget *gadget,
> + struct usb_endpoint_descriptor *desc,
> + struct usb_ss_ep_comp_descriptor *comp_desc)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + struct cdns3_endpoint *priv_ep;
> + unsigned long flags;
> +
> + priv_ep = cdns3_find_available_ep(priv_dev, desc);
> + if (IS_ERR(priv_ep)) {
> + dev_err(priv_dev->dev, "no available ep\n");
> + return NULL;
> + }
> +
> + dev_dbg(priv_dev->dev, "match endpoint: %s\n", priv_ep->name);
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_ep->endpoint.desc = desc;
> + priv_ep->dir = usb_endpoint_dir_in(desc) ? USB_DIR_IN : USB_DIR_OUT;
> + priv_ep->type = usb_endpoint_type(desc);
> + priv_ep->flags |= EP_CLAIMED;
> + priv_ep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return &priv_ep->endpoint;
> +}
> +
> +/**
> + * cdns3_gadget_ep_alloc_request Allocates request
> + * @ep: endpoint object associated with request
> + * @gfp_flags: gfp flags
> + *
> + * Returns allocated request address, NULL on allocation error
> + */
> +struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_request *priv_req;
> +
> + priv_req = kzalloc(sizeof(*priv_req), gfp_flags);
> + if (!priv_req)
> + return NULL;
> +
> + priv_req->priv_ep = priv_ep;
> +
> + trace_cdns3_alloc_request(priv_req);
> + return &priv_req->request;
> +}
> +
> +/**
> + * cdns3_gadget_ep_free_request Free memory occupied by request
> + * @ep: endpoint object associated with request
> + * @request: request to free memory
> + */
> +void cdns3_gadget_ep_free_request(struct usb_ep *ep,
> + struct usb_request *request)
> +{
> + struct cdns3_request *priv_req = to_cdns3_request(request);
> +
> + if (priv_req->aligned_buf)
> + priv_req->aligned_buf->in_use = 0;
> +
> + trace_cdns3_free_request(priv_req);
> + kfree(priv_req);
> +}
> +
> +/**
> + * cdns3_gadget_ep_enable Enable endpoint
> + * @ep: endpoint object
> + * @desc: endpoint descriptor
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep_enable(struct usb_ep *ep,
> + const struct usb_endpoint_descriptor *desc)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_device *priv_dev;
> + u32 reg = EP_STS_EN_TRBERREN;
> + u32 bEndpointAddress;
> + unsigned long flags;
> + int enable = 1;
> + int ret;
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + priv_dev = priv_ep->cdns3_dev;
> +
> + if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
> + dev_dbg(priv_dev->dev, "usbss: invalid parameters\n");
> + return -EINVAL;
> + }
> +
> + if (!desc->wMaxPacketSize) {
> + dev_err(priv_dev->dev, "usbss: missing wMaxPacketSize\n");
> + return -EINVAL;
> + }
> +
> + if (dev_WARN_ONCE(priv_dev->dev, priv_ep->flags & EP_ENABLED,
> + "%s is already enabled\n", priv_ep->name))
> + return 0;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + priv_ep->endpoint.desc = desc;
> + priv_ep->type = usb_endpoint_type(desc);
> + priv_ep->interval = desc->bInterval ? BIT(desc->bInterval - 1) : 0;
> +
> + if (priv_ep->interval > ISO_MAX_INTERVAL &&
> + priv_ep->type == USB_ENDPOINT_XFER_ISOC) {
> + dev_err(priv_dev->dev, "Driver is limited to %d period\n",
> + ISO_MAX_INTERVAL);
> +
> + ret = -EINVAL;
> + goto exit;
> + }
> +
> + ret = cdns3_allocate_trb_pool(priv_ep);
> +
> + if (ret)
> + goto exit;
> +
> + bEndpointAddress = priv_ep->num | priv_ep->dir;
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> +
> + trace_cdns3_gadget_ep_enable(priv_ep);
> +
> + writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_CSTALL | EP_CMD_EPRST, 0, 1000);
> +
> + if (unlikely(ret)) {
> + cdns3_free_trb_pool(priv_ep);
> + ret = -EINVAL;
> + goto exit;
> + }
> +
> + /* enable interrupt for selected endpoint */
> + cdns3_set_register_bit(&priv_dev->regs->ep_ien,
> + BIT(cdns3_ep_addr_to_index(bEndpointAddress)));
> +
> + writel(reg, &priv_dev->regs->ep_sts_en);
> +
> + /*
> + * For some versions of controller at some point during ISO OUT traffic
> + * DMA reads Transfer Ring for the EP which has never got doorbell.
> + * This issue was detected only on simulation, but to avoid this issue
> + * driver add protection against it. To fix it driver enable ISO OUT
> + * endpoint before setting DRBL. This special treatment of ISO OUT
> + * endpoints are recommended by controller specification.
> + */
> + if (priv_ep->type == USB_ENDPOINT_XFER_ISOC && !priv_ep->dir)
> + enable = 0;
> +
> + if (enable)
> + cdns3_set_register_bit(&priv_dev->regs->ep_cfg, EP_CFG_ENABLE);
> +
> + ep->desc = desc;
> + priv_ep->flags &= ~(EP_PENDING_REQUEST | EP_STALL |
> + EP_QUIRK_ISO_OUT_EN);
> + priv_ep->flags |= EP_ENABLED | EP_UPDATE_EP_TRBADDR;
> + priv_ep->wa1_set = 0;
> + priv_ep->enqueue = 0;
> + priv_ep->dequeue = 0;
> + reg = readl(&priv_dev->regs->ep_sts);
> + priv_ep->pcs = !!EP_STS_CCS(reg);
> + priv_ep->ccs = !!EP_STS_CCS(reg);
> + /* one TRB is reserved for link TRB used in DMULT mode*/
> + priv_ep->free_trbs = priv_ep->num_trbs - 1;
> +exit:
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_disable Disable endpoint
> + * @ep: endpoint object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_ep_disable(struct usb_ep *ep)
> +{
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_device *priv_dev;
> + struct usb_request *request;
> + unsigned long flags;
> + int ret = 0;
> + u32 ep_cfg;
> +
> + if (!ep) {
> + pr_err("usbss: invalid parameters\n");
> + return -EINVAL;
> + }
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + priv_dev = priv_ep->cdns3_dev;
> +
> + if (dev_WARN_ONCE(priv_dev->dev, !(priv_ep->flags & EP_ENABLED),
> + "%s is already disabled\n", priv_ep->name))
> + return 0;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + trace_cdns3_gadget_ep_disable(priv_ep);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> +
> + ep_cfg = readl(&priv_dev->regs->ep_cfg);
> + ep_cfg &= ~EP_CFG_ENABLE;
> + writel(ep_cfg, &priv_dev->regs->ep_cfg);
> +
> + /**
> + * Driver needs some time before resetting endpoint.
> + * It need waits for clearing DBUSY bit or for timeout expired.
> + * 10us is enough time for controller to stop transfer.
> + */
> + cdns3_handshake(&priv_dev->regs->ep_sts,
> + EP_STS_DBUSY, 0, 10);
> +
> + writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_CSTALL | EP_CMD_EPRST, 0, 1000);
> +
> + if (unlikely(ret))
> + dev_err(priv_dev->dev, "Timeout: %s resetting failed.\n",
> + priv_ep->name);
> +
> + while (!list_empty(&priv_ep->pending_req_list)) {
> + request = cdns3_next_request(&priv_ep->pending_req_list);
> +
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request),
> + -ESHUTDOWN);
> + }
> +
> + while (!list_empty(&priv_ep->deferred_req_list)) {
> + request = cdns3_next_request(&priv_ep->deferred_req_list);
> +
> + cdns3_gadget_giveback(priv_ep, to_cdns3_request(request),
> + -ESHUTDOWN);
> + }
> +
> + ep->desc = NULL;
> + priv_ep->flags &= ~EP_ENABLED;
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_queue Transfer data on endpoint
> + * @ep: endpoint object
> + * @request: request object
> + * @gfp_flags: gfp flags
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int __cdns3_gadget_ep_queue(struct usb_ep *ep,
> + struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct cdns3_request *priv_req;
> + int ret = 0;
> +
> + request->actual = 0;
> + request->status = -EINPROGRESS;
> + priv_req = to_cdns3_request(request);
> + trace_cdns3_ep_queue(priv_req);
> +
> + ret = cdns3_prepare_aligned_request_buf(priv_req);
> + if (ret < 0)
> + return ret;
> +
> + ret = usb_gadget_map_request_by_dev(priv_dev->sysdev, request,
> + usb_endpoint_dir_in(ep->desc));
> + if (ret)
> + return ret;
> +
> + list_add_tail(&request->list, &priv_ep->deferred_req_list);
> +
> + /*
> + * If hardware endpoint configuration has not been set yet then
> + * just queue request in deferred list. Transfer will be started in
> + * cdns3_set_hw_configuration.
> + */
> + if (priv_dev->hw_configured_flag)
> + cdns3_start_all_request(priv_dev, priv_ep);
> +
> + return 0;
> +}
> +
> +static int cdns3_gadget_ep_queue(struct usb_ep *ep, struct usb_request *request,
> + gfp_t gfp_flags)
> +{
> + struct usb_request *zlp_request;
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_device *priv_dev;
> + unsigned long flags;
> + int ret;
> +
> + if (!request || !ep)
> + return -EINVAL;
> +
> + priv_ep = ep_to_cdns3_ep(ep);
> + priv_dev = priv_ep->cdns3_dev;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + ret = __cdns3_gadget_ep_queue(ep, request, gfp_flags);
> +
> + if (ret == 0 && request->zero && request->length &&
> + (request->length % ep->maxpacket == 0)) {
> + struct cdns3_request *priv_req;
> +
> + zlp_request = cdns3_gadget_ep_alloc_request(ep, GFP_ATOMIC);
> + zlp_request->buf = priv_dev->zlp_buf;
> + zlp_request->length = 0;
> +
> + priv_req = to_cdns3_request(zlp_request);
> + priv_req->flags |= REQUEST_ZLP;
> +
> + dev_dbg(priv_dev->dev, "Queuing ZLP for endpoint: %s\n",
> + priv_ep->name);
> + ret = __cdns3_gadget_ep_queue(ep, zlp_request, gfp_flags);
> + }
> +
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_dequeue Remove request from transfer queue
> + * @ep: endpoint object associated with request
> + * @request: request object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +int cdns3_gadget_ep_dequeue(struct usb_ep *ep,
> + struct usb_request *request)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + struct usb_request *req, *req_temp;
> + struct cdns3_request *priv_req;
> + struct cdns3_trb *link_trb;
> + unsigned long flags;
> + int ret = 0;
> +
> + if (!ep || !request || !ep->desc)
> + return -EINVAL;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + priv_req = to_cdns3_request(request);
> +
> + trace_cdns3_ep_dequeue(priv_req);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> +
> + list_for_each_entry_safe(req, req_temp, &priv_ep->pending_req_list,
> + list) {
> + if (request == req)
> + goto found;
> + }
> +
> + list_for_each_entry_safe(req, req_temp, &priv_ep->deferred_req_list,
> + list) {
> + if (request == req)
> + goto found;
> + }
> +
> + goto not_found;
> +
> +found:
> +
> + if (priv_ep->wa1_trb == priv_req->trb)
> + cdns3_wa1_restore_cycle_bit(priv_ep);
> +
> + link_trb = priv_req->trb;
> + cdns3_move_deq_to_next_trb(priv_req);
> + cdns3_gadget_giveback(priv_ep, priv_req, -ECONNRESET);
> +
> + /* Update ring */
> + request = cdns3_next_request(&priv_ep->deferred_req_list);
> + if (request) {
> + priv_req = to_cdns3_request(request);
> +
> + link_trb->buffer = TRB_BUFFER(priv_ep->trb_pool_dma +
> + (priv_req->start_trb * TRB_SIZE));
> + link_trb->control = (link_trb->control & TRB_CYCLE) |
> + TRB_TYPE(TRB_LINK) | TRB_CHAIN | TRB_TOGGLE;
> + } else {
> + priv_ep->flags |= EP_UPDATE_EP_TRBADDR;
> + }
> +
> +not_found:
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +/**
> + * cdns3_gadget_ep_set_halt Sets/clears stall on selected endpoint
> + * @ep: endpoint object to set/clear stall on
> + * @value: 1 for set stall, 0 for clear stall
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value)
> +{
> + struct cdns3_endpoint *priv_ep = ep_to_cdns3_ep(ep);
> + struct cdns3_device *priv_dev = priv_ep->cdns3_dev;
> + unsigned long flags;
> + int ret = 0;
> +
> + if (!(priv_ep->flags & EP_ENABLED))
> + return -EPERM;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> +
> + cdns3_select_ep(priv_dev, ep->desc->bEndpointAddress);
> + if (value) {
> + cdns3_ep_stall_flush(priv_ep);
> + } else {
> + priv_ep->flags &= ~EP_WEDGE;
> +
> + cdns3_dbg(priv_ep->cdns3_dev, "Clear stalled endpoint %s\n",
> + priv_ep->name);
> +
> + writel(EP_CMD_CSTALL | EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> +
> + /* wait for EPRST cleared */
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + if (unlikely(ret)) {
> + dev_err(priv_dev->dev,
> + "Clearing halt condition failed for %s\n",
> + priv_ep->name);
> + goto finish;
> +
> + } else {
> + priv_ep->flags &= ~EP_STALL;
> + }
> + }
> +
> + priv_ep->flags &= ~EP_PENDING_REQUEST;
> +finish:
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> +
> + return ret;
> +}
> +
> +extern const struct usb_ep_ops cdns3_gadget_ep0_ops;
> +
> +static const struct usb_ep_ops cdns3_gadget_ep_ops = {
> + .enable = cdns3_gadget_ep_enable,
> + .disable = cdns3_gadget_ep_disable,
> + .alloc_request = cdns3_gadget_ep_alloc_request,
> + .free_request = cdns3_gadget_ep_free_request,
> + .queue = cdns3_gadget_ep_queue,
> + .dequeue = cdns3_gadget_ep_dequeue,
> + .set_halt = cdns3_gadget_ep_set_halt,
> + .set_wedge = cdns3_gadget_ep_set_wedge,
> +};
> +
> +/**
> + * cdns3_gadget_get_frame Returns number of actual ITP frame
> + * @gadget: gadget object
> + *
> + * Returns number of actual ITP frame
> + */
> +static int cdns3_gadget_get_frame(struct usb_gadget *gadget)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> +
> + return readl(&priv_dev->regs->usb_itpn);
> +}
> +
> +int __cdns3_gadget_wakeup(struct cdns3_device *priv_dev)
> +{
> + enum usb_device_speed speed;
> +
> + speed = cdns3_get_speed(priv_dev);
> +
> + if (speed >= USB_SPEED_SUPER)
> + return 0;
> +
> + /* Start driving resume signaling to indicate remote wakeup. */
> + writel(USB_CONF_LGO_L0, &priv_dev->regs->usb_conf);
> +
> + return 0;
> +}
> +
> +static int cdns3_gadget_wakeup(struct usb_gadget *gadget)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + unsigned long flags;
> + int ret = 0;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + ret = __cdns3_gadget_wakeup(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return ret;
> +}
> +
> +static int cdns3_gadget_set_selfpowered(struct usb_gadget *gadget,
> + int is_selfpowered)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_dev->is_selfpowered = !!is_selfpowered;
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +static int cdns3_gadget_pullup(struct usb_gadget *gadget, int is_on)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> +
> + if (is_on)
> + writel(USB_CONF_DEVEN, &priv_dev->regs->usb_conf);
> + else
> + writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
> +
> + return 0;
> +}
> +
> +static void cdns3_gadget_config(struct cdns3_device *priv_dev)
> +{
> + struct cdns3_usb_regs __iomem *regs = priv_dev->regs;
> +
> + cdns3_ep0_config(priv_dev);
> +
> + /* enable interrupts for endpoint 0 (in and out) */
> + writel(EP_IEN_EP_OUT0 | EP_IEN_EP_IN0, &regs->ep_ien);
> +
> + /*
> + *Driver need modify LFPS minimal U1 Exit time for 0x00024505 revision
> + * of controller
> + */
> + if (priv_dev->dev_ver == DEV_VER_TI_V1) {
> + u32 reg = readl(&regs->dbg_link1);
> +
> + reg &= ~DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_MASK;
> + reg |= DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(0x55) |
> + DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET;
> + writel(reg, &regs->dbg_link1);
> + }
> +
> + /* enable generic interrupt*/
> + writel(USB_IEN_INIT, &regs->usb_ien);
> + writel(USB_CONF_CLK2OFFDS | USB_CONF_L1DS, &regs->usb_conf);
> +
> + cdns3_configure_dmult(priv_dev, NULL);
> +
> + cdns3_gadget_pullup(&priv_dev->gadget, 1);
> +}
> +
> +/**
> + * cdns3_gadget_udc_start Gadget start
> + * @gadget: gadget object
> + * @driver: driver which operates on this gadget
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
> + struct usb_gadget_driver *driver)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&priv_dev->lock, flags);
> + priv_dev->gadget_driver = driver;
> + cdns3_gadget_config(priv_dev);
> + spin_unlock_irqrestore(&priv_dev->lock, flags);
> + return 0;
> +}
> +
> +/**
> + * cdns3_gadget_udc_stop Stops gadget
> + * @gadget: gadget object
> + *
> + * Returns 0
> + */
> +static int cdns3_gadget_udc_stop(struct usb_gadget *gadget)
> +{
> + struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> + struct cdns3_endpoint *priv_ep;
> + u32 bEndpointAddress;
> + struct usb_ep *ep;
> + int ret = 0;
> +
> + priv_dev->gadget_driver = NULL;
> +
> + priv_dev->onchip_mem_allocated_size = 0;
> + priv_dev->out_mem_is_allocated = 0;
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;

Do you need spin lock for above?

> +
> + list_for_each_entry(ep, &priv_dev->gadget.ep_list, ep_list) {
> + priv_ep = ep_to_cdns3_ep(ep);
> + bEndpointAddress = priv_ep->num | priv_ep->dir;
> + cdns3_select_ep(priv_dev, bEndpointAddress);
> + writel(EP_CMD_EPRST, &priv_dev->regs->ep_cmd);
> + ret = cdns3_handshake(&priv_dev->regs->ep_cmd,
> + EP_CMD_EPRST, 0, 100);
> + cdns3_free_trb_pool(priv_ep);
> + }
> +
> + /* disable interrupt for device */
> + writel(0, &priv_dev->regs->usb_ien);
> + writel(USB_CONF_DEVDS, &priv_dev->regs->usb_conf);
> +
> + return ret;
> +}
> +
> +static const struct usb_gadget_ops cdns3_gadget_ops = {
> + .get_frame = cdns3_gadget_get_frame,
> + .wakeup = cdns3_gadget_wakeup,
> + .set_selfpowered = cdns3_gadget_set_selfpowered,
> + .pullup = cdns3_gadget_pullup,
> + .udc_start = cdns3_gadget_udc_start,
> + .udc_stop = cdns3_gadget_udc_stop,
> + .match_ep = cdns3_gadget_match_ep,
> +};
> +
> +static void cdns3_free_all_eps(struct cdns3_device *priv_dev)
> +{
> + int i;
> +
> + /*ep0 OUT point to ep0 IN*/
> + priv_dev->eps[16] = NULL;
> +
> + cdns3_free_trb_pool(priv_dev->eps[0]);
> +
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++)
> + if (priv_dev->eps[i])
> + devm_kfree(priv_dev->dev, priv_dev->eps[i]);
> +}
> +
> +/**
> + * cdns3_init_eps Initializes software endpoints of gadget
> + * @cdns3: extended gadget object
> + *
> + * Returns 0 on success, error code elsewhere
> + */
> +static int cdns3_init_eps(struct cdns3_device *priv_dev)
> +{
> + u32 ep_enabled_reg, iso_ep_reg;
> + struct cdns3_endpoint *priv_ep;
> + int ep_dir, ep_number;
> + u32 ep_mask;
> + int ret = 0;
> + int i;
> +
> + /* Read it from USB_CAP3 to USB_CAP5 */
> + ep_enabled_reg = readl(&priv_dev->regs->usb_cap3);
> + iso_ep_reg = readl(&priv_dev->regs->usb_cap4);
> +
> + dev_dbg(priv_dev->dev, "Initializing non-zero endpoints\n");
> +
> + for (i = 0; i < CDNS3_ENDPOINTS_MAX_COUNT; i++) {
> + ep_dir = i >> 4; /* i div 16 */
> + ep_number = i & 0xF; /* i % 16 */
> + ep_mask = BIT(i);
> +
> + if (!(ep_enabled_reg & ep_mask))
> + continue;
> +
> + if (ep_dir && !ep_number) {
> + priv_dev->eps[i] = priv_dev->eps[0];
> + continue;
> + }
> +
> + priv_ep = devm_kzalloc(priv_dev->dev, sizeof(*priv_ep),
> + GFP_KERNEL);
> + if (!priv_ep) {
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + /* set parent of endpoint object */
> + priv_ep->cdns3_dev = priv_dev;
> + priv_dev->eps[i] = priv_ep;
> + priv_ep->num = ep_number;
> + priv_ep->dir = ep_dir ? USB_DIR_IN : USB_DIR_OUT;
> +
> + if (!ep_number) {
> + ret = cdns3_init_ep0(priv_dev, priv_ep);
> + if (ret) {
> + dev_err(priv_dev->dev, "Failed to init ep0\n");
> + goto err;
> + }
> + } else {
> + snprintf(priv_ep->name, sizeof(priv_ep->name), "ep%d%s",
> + ep_number, !!ep_dir ? "in" : "out");
> + priv_ep->endpoint.name = priv_ep->name;
> +
> + usb_ep_set_maxpacket_limit(&priv_ep->endpoint,
> + CDNS3_EP_MAX_PACKET_LIMIT);
> + priv_ep->endpoint.max_streams = CDNS3_EP_MAX_STREAMS;
> + priv_ep->endpoint.ops = &cdns3_gadget_ep_ops;
> + if (ep_dir)
> + priv_ep->endpoint.caps.dir_in = 1;
> + else
> + priv_ep->endpoint.caps.dir_out = 1;
> +
> + if (iso_ep_reg & ep_mask)
> + priv_ep->endpoint.caps.type_iso = 1;
> +
> + priv_ep->endpoint.caps.type_bulk = 1;
> + priv_ep->endpoint.caps.type_int = 1;
> +
> + list_add_tail(&priv_ep->endpoint.ep_list,
> + &priv_dev->gadget.ep_list);
> + }
> +
> + priv_ep->flags = 0;
> +
> + dev_info(priv_dev->dev, "Initialized %s support: %s %s\n",
> + priv_ep->name,
> + priv_ep->endpoint.caps.type_bulk ? "BULK, INT" : "",
> + priv_ep->endpoint.caps.type_iso ? "ISO" : "");
> +
> + INIT_LIST_HEAD(&priv_ep->pending_req_list);
> + INIT_LIST_HEAD(&priv_ep->deferred_req_list);
> + }
> +
> + return 0;
> +err:
> + cdns3_free_all_eps(priv_dev);
> + return -ENOMEM;
> +}
> +
> +void cdns3_gadget_exit(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> +
> + priv_dev = cdns->gadget_dev;
> +
> + devm_free_irq(cdns->dev, cdns->dev_irq, cdns);
> +
> + pm_runtime_mark_last_busy(cdns->dev);
> + pm_runtime_put_autosuspend(cdns->dev);
> +
> + usb_del_gadget_udc(&priv_dev->gadget);
> +
> + cdns3_free_all_eps(priv_dev);
> +
> + while (!list_empty(&priv_dev->aligned_buf_list)) {
> + struct cdns3_aligned_buf *buf;
> +
> + buf = cdns3_next_align_buf(&priv_dev->aligned_buf_list);
> + dma_free_coherent(priv_dev->sysdev, buf->size,
> + buf->buf,
> + buf->dma);
> +
> + list_del(&buf->list);
> + kfree(buf);
> + }
> +
> + dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
> + priv_dev->setup_dma);
> +
> + kfree(priv_dev->zlp_buf);
> + kfree(priv_dev);
> + cdns->gadget_dev = NULL;
> + cdns3_drd_switch_gadget(cdns, 0);
> +}
> +
> +static int cdns3_gadget_start(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> + u32 max_speed;
> + int ret;
> +
> + priv_dev = kzalloc(sizeof(*priv_dev), GFP_KERNEL);
> + if (!priv_dev)
> + return -ENOMEM;
> +
> + cdns->gadget_dev = priv_dev;
> + priv_dev->sysdev = cdns->dev;
> + priv_dev->dev = cdns->dev;
> + priv_dev->regs = cdns->dev_regs;
> +
> + max_speed = usb_get_maximum_speed(cdns->dev);
> +
> + /* Check the maximum_speed parameter */
> + switch (max_speed) {
> + case USB_SPEED_FULL:
> + case USB_SPEED_HIGH:
> + case USB_SPEED_SUPER:
> + break;
> + default:
> + dev_err(cdns->dev, "invalid maximum_speed parameter %d\n",
> + max_speed);
> + /* fall through */
> + case USB_SPEED_UNKNOWN:
> + /* default to superspeed */
> + max_speed = USB_SPEED_SUPER;
> + break;
> + }
> +
> + /* fill gadget fields */
> + priv_dev->gadget.max_speed = max_speed;
> + priv_dev->gadget.speed = USB_SPEED_UNKNOWN;
> + priv_dev->gadget.ops = &cdns3_gadget_ops;
> + priv_dev->gadget.name = "usb-ss-gadget";
> + priv_dev->gadget.sg_supported = 1;
> +
> + spin_lock_init(&priv_dev->lock);
> + INIT_WORK(&priv_dev->pending_status_wq,
> + cdns3_pending_setup_status_handler);
> +
> + /* initialize endpoint container */
> + INIT_LIST_HEAD(&priv_dev->gadget.ep_list);
> + INIT_LIST_HEAD(&priv_dev->aligned_buf_list);
> +
> + ret = cdns3_init_eps(priv_dev);
> + if (ret) {
> + dev_err(priv_dev->dev, "Failed to create endpoints\n");
> + goto err1;
> + }
> +
> + /* allocate memory for setup packet buffer */
> + priv_dev->setup_buf = dma_alloc_coherent(priv_dev->sysdev, 8,
> + &priv_dev->setup_dma, GFP_DMA);
> + if (!priv_dev->setup_buf) {
> + dev_err(priv_dev->dev, "Failed to allocate memory for SETUP buffer\n");
> + ret = -ENOMEM;
> + goto err2;
> + }
> +
> + priv_dev->dev_ver = readl(&priv_dev->regs->usb_cap6);
> +
> + dev_dbg(priv_dev->dev, "Device Controller version: %08x\n",
> + readl(&priv_dev->regs->usb_cap6));
> + dev_dbg(priv_dev->dev, "USB Capabilities:: %08x\n",
> + readl(&priv_dev->regs->usb_cap1));
> + dev_dbg(priv_dev->dev, "On-Chip memory cnfiguration: %08x\n",
> + readl(&priv_dev->regs->usb_cap2));
> +
> + priv_dev->dev_ver = GET_DEV_BASE_VERSION(priv_dev->dev_ver);
> +
> + priv_dev->zlp_buf = kzalloc(CDNS3_EP_ZLP_BUF_SIZE, GFP_KERNEL);
> + if (!priv_dev->zlp_buf) {
> + ret = -ENOMEM;
> + goto err3;
> + }
> +
> + /* add USB gadget device */
> + ret = usb_add_gadget_udc(priv_dev->dev, &priv_dev->gadget);
> + if (ret < 0) {
> + dev_err(priv_dev->dev,
> + "Failed to register USB device controller\n");
> + goto err4;
> + }
> +
> + return 0;
> +err4:
> + kfree(priv_dev->zlp_buf);
> +err3:
> + dma_free_coherent(priv_dev->sysdev, 8, priv_dev->setup_buf,
> + priv_dev->setup_dma);
> +err2:
> + cdns3_free_all_eps(priv_dev);
> +err1:

kfree(priv_dev);

Li Jun
> + cdns->gadget_dev = NULL;
> + return ret;
> +}
> +
> +static int __cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + struct cdns3_device *priv_dev;
> + int ret = 0;
> +
> + cdns3_drd_switch_gadget(cdns, 1);
> + pm_runtime_get_sync(cdns->dev);
> +
> + ret = cdns3_gadget_start(cdns);
> + if (ret)
> + return ret;
> +
> + priv_dev = cdns->gadget_dev;
> + ret = devm_request_threaded_irq(cdns->dev, cdns->dev_irq,
> + cdns3_device_irq_handler,
> + cdns3_device_thread_irq_handler,
> + IRQF_SHARED, dev_name(cdns->dev), cdns);
> + if (ret)
> + goto err0;
> +
> + return 0;
> +err0:
> + cdns3_gadget_exit(cdns);
> + return ret;
> +}
> +
> +static int cdns3_gadget_suspend(struct cdns3 *cdns, bool do_wakeup)
> +{
> + cdns3_gadget_exit(cdns);
> + return 0;
> +}
> +
> +static int cdns3_gadget_resume(struct cdns3 *cdns, bool hibernated)
> +{
> + return cdns3_gadget_start(cdns);
> +}
> +
> +/**
> + * cdns3_gadget_init - initialize device structure
> + *
> + * cdns: cdns3 instance
> + *
> + * This function initializes the gadget.
> + */
> +int cdns3_gadget_init(struct cdns3 *cdns)
> +{
> + struct cdns3_role_driver *rdrv;
> +
> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
> + if (!rdrv)
> + return -ENOMEM;
> +
> + rdrv->start = __cdns3_gadget_init;
> + rdrv->stop = cdns3_gadget_exit;
> + rdrv->suspend = cdns3_gadget_suspend;
> + rdrv->resume = cdns3_gadget_resume;
> + rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> + rdrv->name = "gadget";
> + cdns->roles[CDNS3_ROLE_GADGET] = rdrv;
> +
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/gadget.h b/drivers/usb/cdns3/gadget.h
> new file mode 100644
> index 000000000000..bab0cbbe13f4
> --- /dev/null
> +++ b/drivers/usb/cdns3/gadget.h
> @@ -0,0 +1,1313 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * USBSS device controller driver header file
> + *
> + * Copyright (C) 2018-2019 Cadence.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + * Pawel Jez <pjez@xxxxxxxxxxx>
> + * Peter Chen <peter.chen@xxxxxxx>
> + */
> +#ifndef __LINUX_CDNS3_GADGET
> +#define __LINUX_CDNS3_GADGET
> +#include <linux/usb/gadget.h>
> +
> +/*
> + * USBSS-DEV register interface.
> + * This corresponds to the USBSS Device Controller Interface
> + */
> +
> +/**
> + * struct cdns3_usb_regs - device controller registers.
> + * @usb_conf: Global Configuration Register.
> + * @usb_sts: Global Status Register.
> + * @usb_cmd: Global Command Register.
> + * @usb_itpn: ITP/SOF number Register.
> + * @usb_lpm: Global Command Register.
> + * @usb_ien: USB Interrupt Enable Register.
> + * @usb_ists: USB Interrupt Status Register.
> + * @ep_sel: Endpoint Select Register.
> + * @ep_traddr: Endpoint Transfer Ring Address Register.
> + * @ep_cfg: Endpoint Configuration Register.
> + * @ep_cmd: Endpoint Command Register.
> + * @ep_sts: Endpoint Status Register.
> + * @ep_sts_sid: Endpoint Status Register.
> + * @ep_sts_en: Endpoint Status Register Enable.
> + * @drbl: Doorbell Register.
> + * @ep_ien: EP Interrupt Enable Register.
> + * @ep_ists: EP Interrupt Status Register.
> + * @usb_pwr: Global Power Configuration Register.
> + * @usb_conf2: Global Configuration Register 2.
> + * @usb_cap1: Capability Register 1.
> + * @usb_cap2: Capability Register 2.
> + * @usb_cap3: Capability Register 3.
> + * @usb_cap4: Capability Register 4.
> + * @usb_cap5: Capability Register 5.
> + * @usb_cap6: Capability Register 6.
> + * @usb_cpkt1: Custom Packet Register 1.
> + * @usb_cpkt2: Custom Packet Register 2.
> + * @usb_cpkt3: Custom Packet Register 3.
> + * @ep_dma_ext_addr: Upper address for DMA operations Register.
> + * @buf_addr: Address for On-chip Buffer operations Register.
> + * @buf_data: Data for On-chip Buffer operations Register.
> + * @buf_ctrl: On-chip Buffer Access Control Registe.
> + * @dtrans: DMA Transfer Mode Register.
> + * @tdl_from_trb: Source of TD Configuration Register.
> + * @tdl_beh: TDL Behavior Configuration Register.
> + * @ep_tdl: Endpoint TDL Register.
> + * @tdl_beh2: TDL Behavior 2 Configuration Register.
> + * @dma_adv_td: DMA Advance TD Configuration Register.
> + * @reserved1: Reserved.
> + * @cfg_regs: Configuration registers.
> + * @reserved2: Reserved.
> + * @dma_axi_ctrl: AXI Control register.
> + * @dma_axi_id: AXI ID register.
> + * @dma_axi_cap: AXI Capability register.
> + * @dma_axi_ctrl0: AXI Control 0 register.
> + * @dma_axi_ctrl1: AXI Control 1 register.
> + */
> +struct cdns3_usb_regs {
> + __le32 usb_conf;
> + __le32 usb_sts;
> + __le32 usb_cmd;
> + __le32 usb_itpn;
> + __le32 usb_lpm;
> + __le32 usb_ien;
> + __le32 usb_ists;
> + __le32 ep_sel;
> + __le32 ep_traddr;
> + __le32 ep_cfg;
> + __le32 ep_cmd;
> + __le32 ep_sts;
> + __le32 ep_sts_sid;
> + __le32 ep_sts_en;
> + __le32 drbl;
> + __le32 ep_ien;
> + __le32 ep_ists;
> + __le32 usb_pwr;
> + __le32 usb_conf2;
> + __le32 usb_cap1;
> + __le32 usb_cap2;
> + __le32 usb_cap3;
> + __le32 usb_cap4;
> + __le32 usb_cap5;
> + __le32 usb_cap6;
> + __le32 usb_cpkt1;
> + __le32 usb_cpkt2;
> + __le32 usb_cpkt3;
> + __le32 ep_dma_ext_addr;
> + __le32 buf_addr;
> + __le32 buf_data;
> + __le32 buf_ctrl;
> + __le32 dtrans;
> + __le32 tdl_from_trb;
> + __le32 tdl_beh;
> + __le32 ep_tdl;
> + __le32 tdl_beh2;
> + __le32 dma_adv_td;
> + __le32 reserved1[26];
> + __le32 cfg_reg1;
> + __le32 dbg_link1;
> + __le32 dbg_link2;
> + __le32 cfg_regs[74];
> + __le32 reserved2[34];
> + __le32 dma_axi_ctrl;
> + __le32 dma_axi_id;
> + __le32 dma_axi_cap;
> + __le32 dma_axi_ctrl0;
> + __le32 dma_axi_ctrl1;
> +};
> +
> +/* USB_CONF - bitmasks */
> +/* Reset USB device configuration. */
> +#define USB_CONF_CFGRST BIT(0)
> +/* Set Configuration. */
> +#define USB_CONF_CFGSET BIT(1)
> +/* Disconnect USB device in SuperSpeed. */
> +#define USB_CONF_USB3DIS BIT(3)
> +/* Disconnect USB device in HS/FS */
> +#define USB_CONF_USB2DIS BIT(4)
> +/* Little Endian access - default */
> +#define USB_CONF_LENDIAN BIT(5)
> +/*
> + * Big Endian access. Driver assume that byte order for
> + * SFRs access always is as Little Endian so this bit
> + * is not used.
> + */
> +#define USB_CONF_BENDIAN BIT(6)
> +/* Device software reset. */
> +#define USB_CONF_SWRST BIT(7)
> +/* Singular DMA transfer mode. Only for VER < DEV_VER_V3*/
> +#define USB_CONF_DSING BIT(8)
> +/* Multiple DMA transfers mode. Only for VER < DEV_VER_V3 */
> +#define USB_CONF_DMULT BIT(9)
> +/* DMA clock turn-off enable. */
> +#define USB_CONF_DMAOFFEN BIT(10)
> +/* DMA clock turn-off disable. */
> +#define USB_CONF_DMAOFFDS BIT(11)
> +/* Clear Force Full Speed. */
> +#define USB_CONF_CFORCE_FS BIT(12)
> +/* Set Force Full Speed. */
> +#define USB_CONF_SFORCE_FS BIT(13)
> +/* Device enable. */
> +#define USB_CONF_DEVEN BIT(14)
> +/* Device disable. */
> +#define USB_CONF_DEVDS BIT(15)
> +/* L1 LPM state entry enable (used in HS/FS mode). */
> +#define USB_CONF_L1EN BIT(16)
> +/* L1 LPM state entry disable (used in HS/FS mode). */
> +#define USB_CONF_L1DS BIT(17)
> +/* USB 2.0 clock gate disable. */
> +#define USB_CONF_CLK2OFFEN BIT(18)
> +/* USB 2.0 clock gate enable. */
> +#define USB_CONF_CLK2OFFDS BIT(19)
> +/* L0 LPM state entry request (used in HS/FS mode). */
> +#define USB_CONF_LGO_L0 BIT(20)
> +/* USB 3.0 clock gate disable. */
> +#define USB_CONF_CLK3OFFEN BIT(21)
> +/* USB 3.0 clock gate enable. */
> +#define USB_CONF_CLK3OFFDS BIT(22)
> +/* Bit 23 is reserved*/
> +/* U1 state entry enable (used in SS mode). */
> +#define USB_CONF_U1EN BIT(24)
> +/* U1 state entry disable (used in SS mode). */
> +#define USB_CONF_U1DS BIT(25)
> +/* U2 state entry enable (used in SS mode). */
> +#define USB_CONF_U2EN BIT(26)
> +/* U2 state entry disable (used in SS mode). */
> +#define USB_CONF_U2DS BIT(27)
> +/* U0 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U0 BIT(28)
> +/* U1 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U1 BIT(29)
> +/* U2 state entry request (used in SS mode). */
> +#define USB_CONF_LGO_U2 BIT(30)
> +/* SS.Inactive state entry request (used in SS mode) */
> +#define USB_CONF_LGO_SSINACT BIT(31)
> +
> +/* USB_STS - bitmasks */
> +/*
> + * Configuration status.
> + * 1 - device is in the configured state.
> + * 0 - device is not configured.
> + */
> +#define USB_STS_CFGSTS_MASK BIT(0)
> +#define USB_STS_CFGSTS(p) ((p) & USB_STS_CFGSTS_MASK)
> +/*
> + * On-chip memory overflow.
> + * 0 - On-chip memory status OK.
> + * 1 - On-chip memory overflow.
> + */
> +#define USB_STS_OV_MASK BIT(1)
> +#define USB_STS_OV(p) ((p) & USB_STS_OV_MASK)
> +/*
> + * SuperSpeed connection status.
> + * 0 - USB in SuperSpeed mode disconnected.
> + * 1 - USB in SuperSpeed mode connected.
> + */
> +#define USB_STS_USB3CONS_MASK BIT(2)
> +#define USB_STS_USB3CONS(p) ((p) & USB_STS_USB3CONS_MASK)
> +/*
> + * DMA transfer configuration status.
> + * 0 - single request.
> + * 1 - multiple TRB chain
> + * Supported only for controller version < DEV_VER_V3
> + */
> +#define USB_STS_DTRANS_MASK BIT(3)
> +#define USB_STS_DTRANS(p) ((p) & USB_STS_DTRANS_MASK)
> +/*
> + * Device speed.
> + * 0 - Undefined (value after reset).
> + * 1 - Low speed
> + * 2 - Full speed
> + * 3 - High speed
> + * 4 - Super speed
> + */
> +#define USB_STS_USBSPEED_MASK GENMASK(6, 4)
> +#define USB_STS_USBSPEED(p) (((p) & USB_STS_USBSPEED_MASK) >> 4)
> +#define USB_STS_LS (0x1 << 4)
> +#define USB_STS_FS (0x2 << 4)
> +#define USB_STS_HS (0x3 << 4)
> +#define USB_STS_SS (0x4 << 4)
> +#define DEV_UNDEFSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == (0x0 << 4))
> +#define DEV_LOWSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_LS)
> +#define DEV_FULLSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_FS)
> +#define DEV_HIGHSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_HS)
> +#define DEV_SUPERSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_SS)
> +/*
> + * Endianness for SFR access.
> + * 0 - Little Endian order (default after hardware reset).
> + * 1 - Big Endian order
> + */
> +#define USB_STS_ENDIAN_MASK BIT(7)
> +#define USB_STS_ENDIAN(p) ((p) & USB_STS_ENDIAN_MASK)
> +/*
> + * HS/FS clock turn-off status.
> + * 0 - hsfs clock is always on.
> + * 1 - hsfs clock turn-off in L2 (HS/FS mode) is enabled
> + * (default after hardware reset).
> + */
> +#define USB_STS_CLK2OFF_MASK BIT(8)
> +#define USB_STS_CLK2OFF(p) ((p) & USB_STS_CLK2OFF_MASK)
> +/*
> + * PCLK clock turn-off status.
> + * 0 - pclk clock is always on.
> + * 1 - pclk clock turn-off in U3 (SS mode) is enabled
> + * (default after hardware reset).
> + */
> +#define USB_STS_CLK3OFF_MASK BIT(9)
> +#define USB_STS_CLK3OFF(p) ((p) & USB_STS_CLK3OFF_MASK)
> +/*
> + * Controller in reset state.
> + * 0 - Internal reset is active.
> + * 1 - Internal reset is not active and controller is fully operational.
> + */
> +#define USB_STS_IN_RST_MASK BIT(10)
> +#define USB_STS_IN_RST(p) ((p) & USB_STS_IN_RST_MASK)
> +/*
> + * Status of the "TDL calculation basing on TRB" feature.
> + * 0 - disabled
> + * 1 - enabled
> + * Supported only for DEV_VER_V2 controller version.
> + */
> +#define USB_STS_TDL_TRB_ENABLED BIT(11)
> +/*
> + * Device enable Status.
> + * 0 - USB device is disabled (VBUS input is disconnected from internal logic).
> + * 1 - USB device is enabled (VBUS input is connected to the internal logic).
> + */
> +#define USB_STS_DEVS_MASK BIT(14)
> +#define USB_STS_DEVS(p) ((p) & USB_STS_DEVS_MASK)
> +/*
> + * Address status.
> + * 0 - USB device is default state.
> + * 1 - USB device is at least in address state.
> + */
> +#define USB_STS_ADDRESSED_MASK BIT(15)
> +#define USB_STS_ADDRESSED(p) ((p) & USB_STS_ADDRESSED_MASK)
> +/*
> + * L1 LPM state enable status (used in HS/FS mode).
> + * 0 - Entering to L1 LPM state disabled.
> + * 1 - Entering to L1 LPM state enabled.
> + */
> +#define USB_STS_L1ENS_MASK BIT(16)
> +#define USB_STS_L1ENS(p) ((p) & USB_STS_L1ENS_MASK)
> +/*
> + * Internal VBUS connection status (used both in HS/FS and SS mode).
> + * 0 - internal VBUS is not detected.
> + * 1 - internal VBUS is detected.
> + */
> +#define USB_STS_VBUSS_MASK BIT(17)
> +#define USB_STS_VBUSS(p) ((p) & USB_STS_VBUSS_MASK)
> +/*
> + * HS/FS LPM state (used in FS/HS mode).
> + * 0 - L0 State
> + * 1 - L1 State
> + * 2 - L2 State
> + * 3 - L3 State
> + */
> +#define USB_STS_LPMST_MASK GENMASK(19, 18)
> +#define DEV_L0_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x0 << 18))
> +#define DEV_L1_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x1 << 18))
> +#define DEV_L2_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x2 << 18))
> +#define DEV_L3_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x3 << 18))
> +/*
> + * Disable HS status (used in FS/HS mode).
> + * 0 - the disconnect bit for HS/FS mode is set .
> + * 1 - the disconnect bit for HS/FS mode is not set.
> + */
> +#define USB_STS_USB2CONS_MASK BIT(20)
> +#define USB_STS_USB2CONS(p) ((p) & USB_STS_USB2CONS_MASK)
> +/*
> + * HS/FS mode connection status (used in FS/HS mode).
> + * 0 - High Speed operations in USB2.0 (FS/HS) mode not disabled.
> + * 1 - High Speed operations in USB2.0 (FS/HS).
> + */
> +#define USB_STS_DISABLE_HS_MASK BIT(21)
> +#define USB_STS_DISABLE_HS(p) ((p) & USB_STS_DISABLE_HS_MASK)
> +/*
> + * U1 state enable status (used in SS mode).
> + * 0 - Entering to U1 state disabled.
> + * 1 - Entering to U1 state enabled.
> + */
> +#define USB_STS_U1ENS_MASK BIT(24)
> +#define USB_STS_U1ENS(p) ((p) & USB_STS_U1ENS_MASK)
> +/*
> + * U2 state enable status (used in SS mode).
> + * 0 - Entering to U2 state disabled.
> + * 1 - Entering to U2 state enabled.
> + */
> +#define USB_STS_U2ENS_MASK BIT(25)
> +#define USB_STS_U2ENS(p) ((p) & USB_STS_U2ENS_MASK)
> +/*
> + * SuperSpeed Link LTSSM state. This field reflects USBSS-DEV current
> + * SuperSpeed link state
> + */
> +#define USB_STS_LST_MASK GENMASK(29, 26)
> +#define DEV_LST_U0 (((p) & USB_STS_LST_MASK) == (0x0 << 26))
> +#define DEV_LST_U1 (((p) & USB_STS_LST_MASK) == (0x1 << 26))
> +#define DEV_LST_U2 (((p) & USB_STS_LST_MASK) == (0x2 << 26))
> +#define DEV_LST_U3 (((p) & USB_STS_LST_MASK) == (0x3 << 26))
> +#define DEV_LST_DISABLED (((p) & USB_STS_LST_MASK) == (0x4 << 26))
> +#define DEV_LST_RXDETECT (((p) & USB_STS_LST_MASK) == (0x5 << 26))
> +#define DEV_LST_INACTIVE (((p) & USB_STS_LST_MASK) == (0x6 << 26))
> +#define DEV_LST_POLLING (((p) & USB_STS_LST_MASK) == (0x7 << 26))
> +#define DEV_LST_RECOVERY (((p) & USB_STS_LST_MASK) == (0x8 << 26))
> +#define DEV_LST_HOT_RESET (((p) & USB_STS_LST_MASK) == (0x9 << 26))
> +#define DEV_LST_COMP_MODE (((p) & USB_STS_LST_MASK) == (0xa << 26))
> +#define DEV_LST_LB_STATE (((p) & USB_STS_LST_MASK) == (0xb << 26))
> +/*
> + * DMA clock turn-off status.
> + * 0 - DMA clock is always on (default after hardware reset).
> + * 1 - DMA clock turn-off in U1, U2 and U3 (SS mode) is enabled.
> + */
> +#define USB_STS_DMAOFF_MASK BIT(30)
> +#define USB_STS_DMAOFF(p) ((p) & USB_STS_DMAOFF_MASK)
> +/*
> + * SFR Endian status.
> + * 0 - Little Endian order (default after hardware reset).
> + * 1 - Big Endian order.
> + */
> +#define USB_STS_ENDIAN2_MASK BIT(31)
> +#define USB_STS_ENDIAN2(p) ((p) & USB_STS_ENDIAN2_MASK)
> +
> +/* USB_CMD - bitmasks */
> +/* Set Function Address */
> +#define USB_CMD_SET_ADDR BIT(0)
> +/*
> + * Function Address This field is saved to the device only when the field
> + * SET_ADDR is set '1 ' during write to USB_CMD register.
> + * Software is responsible for entering the address of the device during
> + * SET_ADDRESS request service. This field should be set immediately after
> + * the SETUP packet is decoded, and prior to confirmation of the status phase
> + */
> +#define USB_CMD_FADDR_MASK GENMASK(7, 1)
> +#define USB_CMD_FADDR(p) (((p) << 1) & USB_CMD_FADDR_MASK)
> +/* Send Function Wake Device Notification TP (used only in SS mode). */
> +#define USB_CMD_SDNFW BIT(8)
> +/* Set Test Mode (used only in HS/FS mode). */
> +#define USB_CMD_STMODE BIT(9)
> +/* Test mode selector (used only in HS/FS mode) */
> +#define USB_STS_TMODE_SEL_MASK GENMASK(11, 10)
> +#define USB_STS_TMODE_SEL(p) (((p) << 10) & USB_STS_TMODE_SEL_MASK)
> +/*
> + * Send Latency Tolerance Message Device Notification TP (used only
> + * in SS mode).
> + */
> +#define USB_CMD_SDNLTM BIT(12)
> +/* Send Custom Transaction Packet (used only in SS mode) */
> +#define USB_CMD_SPKT BIT(13)
> +/*Device Notification 'Function Wake' - Interface value (only in SS mode. */
> +#define USB_CMD_DNFW_INT_MASK GENMASK(23, 16)
> +#define USB_STS_DNFW_INT(p) (((p) << 16) & USB_CMD_DNFW_INT_MASK)
> +/*
> + * Device Notification 'Latency Tolerance Message' -373 BELT value [7:0]
> + * (used only in SS mode).
> + */
> +#define USB_CMD_DNLTM_BELT_MASK GENMASK(27, 16)
> +#define USB_STS_DNLTM_BELT(p) (((p) << 16) & USB_CMD_DNLTM_BELT_MASK)
> +
> +/* USB_ITPN - bitmasks */
> +/*
> + * ITP(SS) / SOF (HS/FS) number
> + * In SS mode this field represent number of last ITP received from host.
> + * In HS/FS mode this field represent number of last SOF received from host.
> + */
> +#define USB_ITPN_MASK GENMASK(13, 0)
> +#define USB_ITPN(p) ((p) & USB_ITPN_MASK)
> +
> +/* USB_LPM - bitmasks */
> +/* Host Initiated Resume Duration. */
> +#define USB_LPM_HIRD_MASK GENMASK(3, 0)
> +#define USB_LPM_HIRD(p) ((p) & USB_LPM_HIRD_MASK)
> +/* Remote Wakeup Enable (bRemoteWake). */
> +#define USB_LPM_BRW BIT(4)
> +
> +/* USB_IEN - bitmasks */
> +/* SS connection interrupt enable */
> +#define USB_IEN_CONIEN BIT(0)
> +/* SS disconnection interrupt enable. */
> +#define USB_IEN_DISIEN BIT(1)
> +/* USB SS warm reset interrupt enable. */
> +#define USB_IEN_UWRESIEN BIT(2)
> +/* USB SS hot reset interrupt enable */
> +#define USB_IEN_UHRESIEN BIT(3)
> +/* SS link U3 state enter interrupt enable (suspend).*/
> +#define USB_IEN_U3ENTIEN BIT(4)
> +/* SS link U3 state exit interrupt enable (wakeup). */
> +#define USB_IEN_U3EXTIEN BIT(5)
> +/* SS link U2 state enter interrupt enable.*/
> +#define USB_IEN_U2ENTIEN BIT(6)
> +/* SS link U2 state exit interrupt enable.*/
> +#define USB_IEN_U2EXTIEN BIT(7)
> +/* SS link U1 state enter interrupt enable.*/
> +#define USB_IEN_U1ENTIEN BIT(8)
> +/* SS link U1 state exit interrupt enable.*/
> +#define USB_IEN_U1EXTIEN BIT(9)
> +/* ITP/SOF packet detected interrupt enable.*/
> +#define USB_IEN_ITPIEN BIT(10)
> +/* Wakeup interrupt enable.*/
> +#define USB_IEN_WAKEIEN BIT(11)
> +/* Send Custom Packet interrupt enable.*/
> +#define USB_IEN_SPKTIEN BIT(12)
> +/* HS/FS mode connection interrupt enable.*/
> +#define USB_IEN_CON2IEN BIT(16)
> +/* HS/FS mode disconnection interrupt enable.*/
> +#define USB_IEN_DIS2IEN BIT(17)
> +/* USB reset (HS/FS mode) interrupt enable.*/
> +#define USB_IEN_U2RESIEN BIT(18)
> +/* LPM L2 state enter interrupt enable.*/
> +#define USB_IEN_L2ENTIEN BIT(20)
> +/* LPM L2 state exit interrupt enable.*/
> +#define USB_IEN_L2EXTIEN BIT(21)
> +/* LPM L1 state enter interrupt enable.*/
> +#define USB_IEN_L1ENTIEN BIT(24)
> +/* LPM L1 state exit interrupt enable.*/
> +#define USB_IEN_L1EXTIEN BIT(25)
> +/* Configuration reset interrupt enable.*/
> +#define USB_IEN_CFGRESIEN BIT(26)
> +/* Start of the USB SS warm reset interrupt enable.*/
> +#define USB_IEN_UWRESSIEN BIT(28)
> +/* End of the USB SS warm reset interrupt enable.*/
> +#define USB_IEN_UWRESEIEN BIT(29)
> +
> +#define USB_IEN_INIT (USB_IEN_U2RESIEN | USB_ISTS_DIS2I | USB_IEN_CON2IEN \
> + | USB_IEN_UHRESIEN | USB_IEN_UWRESIEN | USB_IEN_DISIEN \
> + | USB_IEN_CONIEN | USB_IEN_U3EXTIEN | USB_IEN_L2ENTIEN \
> + | USB_IEN_L2EXTIEN | USB_IEN_L1ENTIEN)
> +
> +/* USB_ISTS - bitmasks */
> +/* SS Connection detected. */
> +#define USB_ISTS_CONI BIT(0)
> +/* SS Disconnection detected. */
> +#define USB_ISTS_DISI BIT(1)
> +/* UUSB warm reset detectede. */
> +#define USB_ISTS_UWRESI BIT(2)
> +/* USB hot reset detected. */
> +#define USB_ISTS_UHRESI BIT(3)
> +/* U3 link state enter detected (suspend).*/
> +#define USB_ISTS_U3ENTI BIT(4)
> +/* U3 link state exit detected (wakeup). */
> +#define USB_ISTS_U3EXTI BIT(5)
> +/* U2 link state enter detected.*/
> +#define USB_ISTS_U2ENTI BIT(6)
> +/* U2 link state exit detected.*/
> +#define USB_ISTS_U2EXTI BIT(7)
> +/* U1 link state enter detected.*/
> +#define USB_ISTS_U1ENTI BIT(8)
> +/* U1 link state exit detected.*/
> +#define USB_ISTS_U1EXTI BIT(9)
> +/* ITP/SOF packet detected.*/
> +#define USB_ISTS_ITPI BIT(10)
> +/* Wakeup detected.*/
> +#define USB_ISTS_WAKEI BIT(11)
> +/* Send Custom Packet detected.*/
> +#define USB_ISTS_SPKTI BIT(12)
> +/* HS/FS mode connection detected.*/
> +#define USB_ISTS_CON2I BIT(16)
> +/* HS/FS mode disconnection detected.*/
> +#define USB_ISTS_DIS2I BIT(17)
> +/* USB reset (HS/FS mode) detected.*/
> +#define USB_ISTS_U2RESI BIT(18)
> +/* LPM L2 state enter detected.*/
> +#define USB_ISTS_L2ENTI BIT(20)
> +/* LPM L2 state exit detected.*/
> +#define USB_ISTS_L2EXTI BIT(21)
> +/* LPM L1 state enter detected.*/
> +#define USB_ISTS_L1ENTI BIT(24)
> +/* LPM L1 state exit detected.*/
> +#define USB_ISTS_L1EXTI BIT(25)
> +/* USB configuration reset detected.*/
> +#define USB_ISTS_CFGRESI BIT(26)
> +/* Start of the USB warm reset detected.*/
> +#define USB_ISTS_UWRESSI BIT(28)
> +/* End of the USB warm reset detected.*/
> +#define USB_ISTS_UWRESEI BIT(29)
> +
> +/* USB_SEL - bitmasks */
> +#define EP_SEL_EPNO_MASK GENMASK(3, 0)
> +/* Endpoint number. */
> +#define EP_SEL_EPNO(p) ((p) & EP_SEL_EPNO_MASK)
> +/* Endpoint direction bit - 0 - OUT, 1 - IN. */
> +#define EP_SEL_DIR BIT(7)
> +
> +#define select_ep_in(nr) (EP_SEL_EPNO(p) | EP_SEL_DIR)
> +#define select_ep_out (EP_SEL_EPNO(p))
> +
> +/* EP_TRADDR - bitmasks */
> +/* Transfer Ring address. */
> +#define EP_TRADDR_TRADDR(p) ((p))
> +
> +/* EP_CFG - bitmasks */
> +/* Endpoint enable */
> +#define EP_CFG_ENABLE BIT(0)
> +/*
> + * Endpoint type.
> + * 1 - isochronous
> + * 2 - bulk
> + * 3 - interrupt
> + */
> +#define EP_CFG_EPTYPE_MASK GENMASK(2, 1)
> +#define EP_CFG_EPTYPE(p) (((p) << 1) & EP_CFG_EPTYPE_MASK)
> +/* Stream support enable (only in SS mode). */
> +#define EP_CFG_STREAM_EN BIT(3)
> +/* TDL check (only in SS mode for BULK EP). */
> +#define EP_CFG_TDL_CHK BIT(4)
> +/* SID check (only in SS mode for BULK OUT EP). */
> +#define EP_CFG_SID_CHK BIT(5)
> +/* DMA transfer endianness. */
> +#define EP_CFG_EPENDIAN BIT(7)
> +/* Max burst size (used only in SS mode). */
> +#define EP_CFG_MAXBURST_MASK GENMASK(11, 8)
> +#define EP_CFG_MAXBURST(p) (((p) << 8) & EP_CFG_MAXBURST_MASK)
> +/* ISO max burst. */
> +#define EP_CFG_MULT_MASK GENMASK(15, 14)
> +#define EP_CFG_MULT(p) (((p) << 14) & EP_CFG_MULT_MASK)
> +/* ISO max burst. */
> +#define EP_CFG_MAXPKTSIZE_MASK GENMASK(26, 16)
> +#define EP_CFG_MAXPKTSIZE(p) (((p) << 16) & EP_CFG_MAXPKTSIZE_MASK)
> +/* Max number of buffered packets. */
> +#define EP_CFG_BUFFERING_MASK GENMASK(31, 27)
> +#define EP_CFG_BUFFERING(p) (((p) << 27) & EP_CFG_BUFFERING_MASK)
> +
> +/* EP_CMD - bitmasks */
> +/* Endpoint reset. */
> +#define EP_CMD_EPRST BIT(0)
> +/* Endpoint STALL set. */
> +#define EP_CMD_SSTALL BIT(1)
> +/* Endpoint STALL clear. */
> +#define EP_CMD_CSTALL BIT(2)
> +/* Send ERDY TP. */
> +#define EP_CMD_ERDY BIT(3)
> +/* Request complete. */
> +#define EP_CMD_REQ_CMPL BIT(5)
> +/* Transfer descriptor ready. */
> +#define EP_CMD_DRDY BIT(6)
> +/* Data flush. */
> +#define EP_CMD_DFLUSH BIT(7)
> +/*
> + * Transfer Descriptor Length write (used only for Bulk Stream capable
> + * endpoints in SS mode).
> + * Bit Removed from DEV_VER_V3 controller version.
> + */
> +#define EP_CMD_STDL BIT(8)
> +/*
> + * Transfer Descriptor Length (used only in SS mode for bulk endpoints).
> + * Bits Removed from DEV_VER_V3 controller version.
> + */
> +#define EP_CMD_TDL_MASK GENMASK(15, 9)
> +#define EP_CMD_TDL(p) (((p) << 9) & EP_CMD_TDL_MASK)
> +/* ERDY Stream ID value (used in SS mode). */
> +#define EP_CMD_ERDY_SID_MASK GENMASK(31, 16)
> +#define EP_CMD_ERDY_SID(p) (((p) << 16) & EP_CMD_SID_MASK)
> +
> +/* EP_STS - bitmasks */
> +/* Setup transfer complete. */
> +#define EP_STS_SETUP BIT(0)
> +/* Endpoint STALL status. */
> +#define EP_STS_STALL(p) ((p) & BIT(1))
> +/* Interrupt On Complete. */
> +#define EP_STS_IOC BIT(2)
> +/* Interrupt on Short Packet. */
> +#define EP_STS_ISP BIT(3)
> +/* Transfer descriptor missing. */
> +#define EP_STS_DESCMIS BIT(4)
> +/* Stream Rejected (used only in SS mode) */
> +#define EP_STS_STREAMR BIT(5)
> +/* EXIT from MOVE DATA State (used only for stream transfers in SS mode). */
> +#define EP_STS_MD_EXIT BIT(6)
> +/* TRB error. */
> +#define EP_STS_TRBERR BIT(7)
> +/* Not ready (used only in SS mode). */
> +#define EP_STS_NRDY BIT(8)
> +/* DMA busy bit. */
> +#define EP_STS_DBUSY BIT(9)
> +/* Endpoint Buffer Empty */
> +#define EP_STS_BUFFEMPTY(p) ((p) & BIT(10))
> +/* Current Cycle Status */
> +#define EP_STS_CCS(p) ((p) & BIT(11))
> +/* Prime (used only in SS mode. */
> +#define EP_STS_PRIME BIT(12)
> +/* Stream error (used only in SS mode). */
> +#define EP_STS_SIDERR BIT(13)
> +/* OUT size mismatch. */
> +#define EP_STS_OUTSMM BIT(14)
> +/* ISO transmission error. */
> +#define EP_STS_ISOERR BIT(15)
> +/* Host Packet Pending (only for SS mode). */
> +#define EP_STS_HOSTPP(p) ((p) & BIT(16))
> +/* Stream Protocol State Machine State (only for Bulk stream endpoints). */
> +#define EP_STS_SPSMST_MASK GENMASK(18, 17)
> +#define EP_STS_SPSMST_DISABLED(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_IDLE(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_START_STREAM(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +#define EP_STS_SPSMST_MOVE_DATA(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
> +/* Interrupt On Transfer complete. */
> +#define EP_STS_IOT BIT(19)
> +/* OUT queue endpoint number. */
> +#define EP_STS_OUTQ_NO_MASK GENMASK(27, 24)
> +#define EP_STS_OUTQ_NO(p) (((p) & EP_STS_OUTQ_NO_MASK) >> 24)
> +/* OUT queue valid flag. */
> +#define EP_STS_OUTQ_VAL_MASK BIT(28)
> +#define EP_STS_OUTQ_VAL(p) ((p) & EP_STS_OUTQ_VAL_MASK)
> +/* SETUP WAIT. */
> +#define EP_STS_STPWAIT BIT(31)
> +
> +/* EP_STS_SID - bitmasks */
> +/* Stream ID (used only in SS mode). */
> +#define EP_STS_SID_MASK GENMASK(15, 0)
> +#define EP_STS_SID(p) ((p) & EP_STS_SID_MASK)
> +
> +/* EP_STS_EN - bitmasks */
> +/* SETUP interrupt enable. */
> +#define EP_STS_EN_SETUPEN BIT(0)
> +/* OUT transfer missing descriptor enable. */
> +#define EP_STS_EN_DESCMISEN BIT(4)
> +/* Stream Rejected enable. */
> +#define EP_STS_EN_STREAMREN BIT(5)
> +/* Move Data Exit enable.*/
> +#define EP_STS_EN_MD_EXITEN BIT(6)
> +/* TRB enable. */
> +#define EP_STS_EN_TRBERREN BIT(7)
> +/* NRDY enable. */
> +#define EP_STS_EN_NRDYEN BIT(8)
> +/* Prime enable. */
> +#define EP_STS_EN_PRIMEEEN BIT(12)
> +/* Stream error enable. */
> +#define EP_STS_EN_SIDERREN BIT(13)
> +/* OUT size mismatch enable. */
> +#define EP_STS_EN_OUTSMMEN BIT(14)
> +/* ISO transmission error enable. */
> +#define EP_STS_EN_ISOERREN BIT(15)
> +/* Interrupt on Transmission complete enable. */
> +#define EP_STS_EN_IOTEN BIT(19)
> +/* Setup Wait interrupt enable. */
> +#define EP_STS_EN_STPWAITEN BIT(31)
> +
> +/* DRBL- bitmasks */
> +#define DB_VALUE_BY_INDEX(index) (1 << (index))
> +#define DB_VALUE_EP0_OUT BIT(0)
> +#define DB_VALUE_EP0_IN BIT(16)
> +
> +/* EP_IEN - bitmasks */
> +#define EP_IEN(index) (1 << (index))
> +#define EP_IEN_EP_OUT0 BIT(0)
> +#define EP_IEN_EP_IN0 BIT(16)
> +
> +/* EP_ISTS - bitmasks */
> +#define EP_ISTS(index) (1 << (index))
> +#define EP_ISTS_EP_OUT0 BIT(0)
> +#define EP_ISTS_EP_IN0 BIT(16)
> +
> +/* USB_PWR- bitmasks */
> +/*Power Shut Off capability enable*/
> +#define PUSB_PWR_PSO_EN BIT(0)
> +/*Power Shut Off capability disable*/
> +#define PUSB_PWR_PSO_DS BIT(1)
> +/*
> + * Enables turning-off Reference Clock.
> + * This bit is optional and implemented only when support for OTG is
> + * implemented (indicated by OTG_READY bit set to '1').
> + */
> +#define PUSB_PWR_STB_CLK_SWITCH_EN BIT(8)
> +/*
> + * Status bit indicating that operation required by STB_CLK_SWITCH_EN write
> + * is completed
> + */
> +#define PUSB_PWR_STB_CLK_SWITCH_DONE BIT(9)
> +/* This bit informs if Fast Registers Access is enabled. */
> +#define PUSB_PWR_FST_REG_ACCESS_STAT BIT(30)
> +/* Fast Registers Access Enable. */
> +#define PUSB_PWR_FST_REG_ACCESS BIT(31)
> +
> +/* USB_CONF2- bitmasks */
> +/*
> + * Writing 1 disables TDL calculation basing on TRB feature in controller
> + * for DMULT mode.
> + * Bit supported only for DEV_VER_V2 version.
> + */
> +#define USB_CONF2_DIS_TDL_TRB BIT(1)
> +/*
> + * Writing 1 enables TDL calculation basing on TRB feature in controller
> + * for DMULT mode.
> + * Bit supported only for DEV_VER_V2 version.
> + */
> +#define USB_CONF2_EN_TDL_TRB BIT(2)
> +
> +/* USB_CAP1- bitmasks */
> +/*
> + * SFR Interface type
> + * These field reflects type of SFR interface implemented:
> + * 0x0 - OCP
> + * 0x1 - AHB,
> + * 0x2 - PLB
> + * 0x3 - AXI
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_SFR_TYPE_MASK GENMASK(3, 0)
> +#define DEV_SFR_TYPE_OCP(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x0)
> +#define DEV_SFR_TYPE_AHB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x1)
> +#define DEV_SFR_TYPE_PLB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x2)
> +#define DEV_SFR_TYPE_AXI(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x3)
> +/*
> + * SFR Interface width
> + * These field reflects width of SFR interface implemented:
> + * 0x0 - 8 bit interface,
> + * 0x1 - 16 bit interface,
> + * 0x2 - 32 bit interface
> + * 0x3 - 64 bit interface
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_SFR_WIDTH_MASK GENMASK(7, 4)
> +#define DEV_SFR_WIDTH_8(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x0 << 4))
> +#define DEV_SFR_WIDTH_16(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x1 << 4))
> +#define DEV_SFR_WIDTH_32(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x2 << 4))
> +#define DEV_SFR_WIDTH_64(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x3 << 4))
> +/*
> + * DMA Interface type
> + * These field reflects type of DMA interface implemented:
> + * 0x0 - OCP
> + * 0x1 - AHB,
> + * 0x2 - PLB
> + * 0x3 - AXI
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_DMA_TYPE_MASK GENMASK(11, 8)
> +#define DEV_DMA_TYPE_OCP(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x0 << 8))
> +#define DEV_DMA_TYPE_AHB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x1 << 8))
> +#define DEV_DMA_TYPE_PLB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x2 << 8))
> +#define DEV_DMA_TYPE_AXI(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x3 << 8))
> +/*
> + * DMA Interface width
> + * These field reflects width of DMA interface implemented:
> + * 0x0 - reserved,
> + * 0x1 - reserved,
> + * 0x2 - 32 bit interface
> + * 0x3 - 64 bit interface
> + * 0x4-0xF - reserved
> + */
> +#define USB_CAP1_DMA_WIDTH_MASK GENMASK(15, 12)
> +#define DEV_DMA_WIDTH_32(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x2 << 12))
> +#define DEV_DMA_WIDTH_64(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x3 << 12))
> +/*
> + * USB3 PHY Interface type
> + * These field reflects type of USB3 PHY interface implemented:
> + * 0x0 - USB PIPE,
> + * 0x1 - RMMI,
> + * 0x2-0xF - reserved
> + */
> +#define USB_CAP1_U3PHY_TYPE_MASK GENMASK(19, 16)
> +#define DEV_U3PHY_PIPE(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x0 << 16))
> +#define DEV_U3PHY_RMMI(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x1 << 16))
> +/*
> + * USB3 PHY Interface width
> + * These field reflects width of USB3 PHY interface implemented:
> + * 0x0 - 8 bit PIPE interface,
> + * 0x1 - 16 bit PIPE interface,
> + * 0x2 - 32 bit PIPE interface,
> + * 0x3 - 64 bit PIPE interface
> + * 0x4-0xF - reserved
> + * Note: When SSIC interface is implemented this field shows the width of
> + * internal PIPE interface. The RMMI interface is always 20bit wide.
> + */
> +#define USB_CAP1_U3PHY_WIDTH_MASK GENMASK(23, 20)
> +#define DEV_U3PHY_WIDTH_8(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x0 << 20))
> +#define DEV_U3PHY_WIDTH_16(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x1 << 16))
> +#define DEV_U3PHY_WIDTH_32(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x2 << 20))
> +#define DEV_U3PHY_WIDTH_64(p) \
> + (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x3 << 16))
> +
> +/*
> + * USB2 PHY Interface enable
> + * These field informs if USB2 PHY interface is implemented:
> + * 0x0 - interface NOT implemented,
> + * 0x1 - interface implemented
> + */
> +#define USB_CAP1_U2PHY_EN(p) ((p) & BIT(24))
> +/*
> + * USB2 PHY Interface type
> + * These field reflects type of USB2 PHY interface implemented:
> + * 0x0 - UTMI,
> + * 0x1 - ULPI
> + */
> +#define DEV_U2PHY_ULPI(p) ((p) & BIT(25))
> +/*
> + * USB2 PHY Interface width
> + * These field reflects width of USB2 PHY interface implemented:
> + * 0x0 - 8 bit interface,
> + * 0x1 - 16 bit interface,
> + * Note: The ULPI interface is always 8bit wide.
> + */
> +#define DEV_U2PHY_WIDTH_16(p) ((p) & BIT(26))
> +/*
> + * OTG Ready
> + * 0x0 - pure device mode
> + * 0x1 - some features and ports for CDNS USB OTG controller are implemented.
> + */
> +#define USB_CAP1_OTG_READY(p) ((p) & BIT(27))
> +
> +/*
> + * When set, indicates that controller supports automatic internal TDL
> + * calculation basing on the size provided in TRB (TRB[22:17]) for DMULT mode
> + * Supported only for DEV_VER_V2 controller version.
> + */
> +#define USB_CAP1_TDL_FROM_TRB(p) ((p) & BIT(28))
> +
> +/* USB_CAP2- bitmasks */
> +/*
> + * The actual size of the connected On-chip RAM memory in kB:
> + * - 0 means 256 kB (max supported mem size)
> + * - value other than 0 reflects the mem size in kB
> + */
> +#define USB_CAP2_ACTUAL_MEM_SIZE(p) ((p) & GENMASK(7, 0))
> +/*
> + * Max supported mem size
> + * These field reflects width of on-chip RAM address bus width,
> + * which determines max supported mem size:
> + * 0x0-0x7 - reserved,
> + * 0x8 - support for 4kB mem,
> + * 0x9 - support for 8kB mem,
> + * 0xA - support for 16kB mem,
> + * 0xB - support for 32kB mem,
> + * 0xC - support for 64kB mem,
> + * 0xD - support for 128kB mem,
> + * 0xE - support for 256kB mem,
> + * 0xF - reserved
> + */
> +#define USB_CAP2_MAX_MEM_SIZE(p) ((p) & GENMASK(11, 8))
> +
> +/* USB_CAP3- bitmasks */
> +#define EP_IS_IMPLEMENTED(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP4- bitmasks */
> +#define EP_SUPPORT_ISO(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP5- bitmasks */
> +#define EP_SUPPORT_STREAM(reg, index) ((reg) & (1 << (index)))
> +
> +/* USB_CAP6- bitmasks */
> +/* The USBSS-DEV Controller Internal build number. */
> +#define GET_DEV_BASE_VERSION(p) ((p) & GENMASK(23, 0))
> +/* The USBSS-DEV Controller version number. */
> +#define GET_DEV_CUSTOM_VERSION(p) ((p) & GENMASK(31, 24))
> +
> +#define DEV_VER_NXP_V1 0x00024502
> +#define DEV_VER_TI_V1 0x00024509
> +#define DEV_VER_V2 0x0002450C
> +#define DEV_VER_V3 0x0002450d
> +
> +/* DBG_LINK1- bitmasks */
> +/*
> + * LFPS_MIN_DET_U1_EXIT value This parameter configures the minimum
> + * time required for decoding the received LFPS as an LFPS.U1_Exit.
> + */
> +#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT(p) ((p) & GENMASK(7, 0))
> +/*
> + * LFPS_MIN_GEN_U1_EXIT value This parameter configures the minimum time for
> + * phytxelecidle deassertion when LFPS.U1_Exit
> + */
> +#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_MASK GENMASK(15, 8)
> +#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(p) (((p) << 8) & GENMASK(15, 8))
> +/*
> + * RXDET_BREAK_DIS value This parameter configures terminating the Far-end
> + * Receiver termination detection sequence:
> + * 0: it is possible that USBSS_DEV will terminate Farend receiver
> + * termination detection sequence
> + * 1: USBSS_DEV will not terminate Far-end receiver termination
> + * detection sequence
> + */
> +#define DBG_LINK1_RXDET_BREAK_DIS BIT(16)
> +/* LFPS_GEN_PING value This parameter configures the LFPS.Ping generation */
> +#define DBG_LINK1_LFPS_GEN_PING(p) (((p) << 17) & GENMASK(21, 17))
> +/*
> + * Set the LFPS_MIN_DET_U1_EXIT value Writing '1' to this bit writes the
> + * LFPS_MIN_DET_U1_EXIT field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT_SET BIT(24)
> +/*
> + * Set the LFPS_MIN_GEN_U1_EXIT value. Writing '1' to this bit writes the
> + * LFPS_MIN_GEN_U1_EXIT field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET BIT(25)
> +/*
> + * Set the RXDET_BREAK_DIS value Writing '1' to this bit writes
> + * the RXDET_BREAK_DIS field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect
> + */
> +#define DBG_LINK1_RXDET_BREAK_DIS_SET BIT(26)
> +/*
> + * Set the LFPS_GEN_PING_SET value Writing '1' to this bit writes
> + * the LFPS_GEN_PING field value to the device. This bit is automatically
> + * cleared. Writing '0' has no effect."
> + */
> +#define DBG_LINK1_LFPS_GEN_PING_SET BIT(27)
> +
> +#define gadget_to_cdns3_device(g) (container_of(g, struct cdns3_device, gadget))
> +
> +#define ep_to_cdns3_ep(ep) (container_of(ep, struct cdns3_endpoint, endpoint))
> +
> +/*-------------------------------------------------------------------------*/
> +/*
> + * USBSS-DEV DMA interface.
> + */
> +#define TRBS_PER_SEGMENT 40
> +
> +#define ISO_MAX_INTERVAL 10
> +
> +#if TRBS_PER_SEGMENT < 2
> +#error "Incorrect TRBS_PER_SEGMENT. Minimal Transfer Ring size is 2."
> +#endif
> +
> +/*
> + *Only for ISOC endpoints - maximum number of TRBs is calculated as
> + * pow(2, bInterval-1) * number of usb requests. It is limitation made by
> + * driver to save memory. Controller must prepare TRB for each ITP even
> + * if bInterval > 1. It's the reason why driver needs so many TRBs for
> + * isochronous endpoints.
> + */
> +#define TRBS_PER_ISOC_SEGMENT (ISO_MAX_INTERVAL * 8)
> +
> +#define GET_TRBS_PER_SEGMENT(ep_type) ((ep_type) == USB_ENDPOINT_XFER_ISOC ? \
> + TRBS_PER_ISOC_SEGMENT : TRBS_PER_SEGMENT)
> +/**
> + * struct cdns3_trb - represent Transfer Descriptor block.
> + * @buffer: pointer to buffer data
> + * @length: length of data
> + * @control: control flags.
> + *
> + * This structure describes transfer block serviced by DMA module.
> + */
> +struct cdns3_trb {
> + __le32 buffer;
> + __le32 length;
> + __le32 control;
> +};
> +
> +#define TRB_SIZE (sizeof(struct cdns3_trb))
> +#define TRB_RING_SIZE (TRB_SIZE * TRBS_PER_SEGMENT)
> +#define TRB_ISO_RING_SIZE (TRB_SIZE * TRBS_PER_ISOC_SEGMENT)
> +#define TRB_CTRL_RING_SIZE (TRB_SIZE * 2)
> +
> +/* TRB bit mask */
> +#define TRB_TYPE_BITMASK GENMASK(15, 10)
> +#define TRB_TYPE(p) ((p) << 10)
> +#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
> +
> +/* TRB type IDs */
> +/* bulk, interrupt, isoc , and control data stage */
> +#define TRB_NORMAL 1
> +/* TRB for linking ring segments */
> +#define TRB_LINK 6
> +
> +/* Cycle bit - indicates TRB ownership by driver or hw*/
> +#define TRB_CYCLE BIT(0)
> +/*
> + * When set to '1', the device will toggle its interpretation of the Cycle bit
> + */
> +#define TRB_TOGGLE BIT(1)
> +
> +/*
> + * Short Packet (SP). OUT EPs at DMULT=1 only. Indicates if the TRB was
> + * processed while USB short packet was received. No more buffers defined by
> + * the TD will be used. DMA will automatically advance to next TD.
> + * - Shall be set to 0 by Software when putting TRB on the Transfer Ring
> + * - Shall be set to 1 by Controller when Short Packet condition for this TRB
> + * is detected independent if ISP is set or not.
> + */
> +#define TRB_SP BIT(1)
> +
> +/* Interrupt on short packet*/
> +#define TRB_ISP BIT(2)
> +/*Setting this bit enables FIFO DMA operation mode*/
> +#define TRB_FIFO_MODE BIT(3)
> +/* Set PCIe no snoop attribute */
> +#define TRB_CHAIN BIT(4)
> +/* Interrupt on completion */
> +#define TRB_IOC BIT(5)
> +
> +/* stream ID bitmasks. */
> +#define TRB_STREAM_ID(p) ((p) & GENMASK(31, 16))
> +
> +/* Size of TD expressed in USB packets for HS/FS mode. */
> +#define TRB_TDL_HS_SIZE(p) (((p) << 16) & GENMASK(31, 16))
> +#define TRB_TDL_HS_SIZE_GET(p) (((p) & GENMASK(31, 16)) >> 16)
> +
> +/* transfer_len bitmasks. */
> +#define TRB_LEN(p) ((p) & GENMASK(16, 0))
> +
> +/* Size of TD expressed in USB packets for SS mode. */
> +#define TRB_TDL_SS_SIZE(p) (((p) << 17) & GENMASK(23, 17))
> +#define TRB_TDL_SS_SIZE_GET(p) (((p) & GENMASK(23, 17)) >> 17)
> +
> +/* transfer_len bitmasks - bits 31:24 */
> +#define TRB_BURST_LEN(p) (((p) << 24) & GENMASK(31, 24))
> +#define TRB_BURST_LEN_GET(p) (((p) & GENMASK(31, 24)) >> 24)
> +
> +/* Data buffer pointer bitmasks*/
> +#define TRB_BUFFER(p) ((p) & GENMASK(31, 0))
> +
> +/*-------------------------------------------------------------------------*/
> +/* Driver numeric constants */
> +
> +/* Such declaration should be added to ch9.h */
> +#define USB_DEVICE_MAX_ADDRESS 127
> +
> +/* Endpoint init values */
> +#define CDNS3_EP_MAX_PACKET_LIMIT 1024
> +#define CDNS3_EP_MAX_STREAMS 15
> +#define CDNS3_EP0_MAX_PACKET_LIMIT 512
> +
> +/* All endpoints including EP0 */
> +#define CDNS3_ENDPOINTS_MAX_COUNT 32
> +#define CDNS3_EP_ZLP_BUF_SIZE 1024
> +
> +#define CDNS3_EP_BUF_SIZE 2 /* KB */
> +#define CDNS3_EP_ISO_HS_MULT 3
> +#define CDNS3_EP_ISO_SS_BURST 3
> +#define CDNS3_MAX_NUM_DESCMISS_BUF 32
> +#define CDNS3_DESCMIS_BUF_SIZE 2048 /* Bytes */
> +/*-------------------------------------------------------------------------*/
> +/* Used structs */
> +
> +struct cdns3_device;
> +
> +/**
> + * struct cdns3_endpoint - extended device side representation of USB endpoint.
> + * @endpoint: usb endpoint
> + * @pending_req_list: list of requests queuing on transfer ring.
> + * @deferred_req_list: list of requests waiting for queuing on transfer ring.
> + * @trb_pool: transfer ring - array of transaction buffers
> + * @trb_pool_dma: dma address of transfer ring
> + * @cdns3_dev: device associated with this endpoint
> + * @name: a human readable name e.g. ep1out
> + * @flags: specify the current state of endpoint
> + * @dir: endpoint direction
> + * @num: endpoint number (1 - 15)
> + * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
> + * @interval: interval between packets used for ISOC endpoint.
> + * @free_trbs: number of free TRBs in transfer ring
> + * @num_trbs: number of all TRBs in transfer ring
> + * @pcs: producer cycle state
> + * @ccs: consumer cycle state
> + * @enqueue: enqueue index in transfer ring
> + * @dequeue: dequeue index in transfer ring
> + * @trb_burst_size: number of burst used in trb.
> + */
> +struct cdns3_endpoint {
> + struct usb_ep endpoint;
> + struct list_head pending_req_list;
> + struct list_head deferred_req_list;
> +
> + struct cdns3_trb *trb_pool;
> + dma_addr_t trb_pool_dma;
> +
> + struct cdns3_device *cdns3_dev;
> + char name[20];
> +
> +#define EP_ENABLED BIT(0)
> +#define EP_STALL BIT(1)
> +#define EP_WEDGE BIT(2)
> +#define EP_TRANSFER_STARTED BIT(3)
> +#define EP_UPDATE_EP_TRBADDR BIT(4)
> +#define EP_PENDING_REQUEST BIT(5)
> +#define EP_RING_FULL BIT(6)
> +#define EP_CLAIMED BIT(7)
> +#define EP_DEFERRED_DRDY BIT(8)
> +#define EP_QUIRK_ISO_OUT_EN BIT(9)
> + u32 flags;
> +
> + u8 dir;
> + u8 num;
> + u8 type;
> + int interval;
> +
> + int free_trbs;
> + int num_trbs;
> + u8 pcs;
> + u8 ccs;
> + int enqueue;
> + int dequeue;
> + u8 trb_burst_size;
> +
> + unsigned int wa1_set:1;
> + struct cdns3_trb *wa1_trb;
> + unsigned int wa1_trb_index;
> + unsigned int wa1_cycle_bit:1;
> +};
> +
> +/**
> + * struct cdns3_aligned_buf - represent aligned buffer used for DMA transfer
> + * @buf: aligned to 8 bytes data buffer. Buffer address used in
> + * TRB shall be aligned to 8.
> + * @dma: dma address
> + * @size: size of buffer
> + * @in_use: inform if this buffer is associated with usb_request
> + * @list: used to adding instance of this object to list
> + */
> +struct cdns3_aligned_buf {
> + void *buf;
> + dma_addr_t dma;
> + u32 size;
> + int in_use:1;
> + struct list_head list;
> +};
> +
> +/**
> + * struct cdns3_request - extended device side representation of usb_request
> + * object .
> + * @request: generic usb_request object describing single I/O request.
> + * @priv_ep: extended representation of usb_ep object
> + * @trb: the first TRB association with this request
> + * @start_trb: number of the first TRB in transfer ring
> + * @end_trb: number of the last TRB in transfer ring
> + * @aligned_buf: object holds information about aligned buffer associated whit
> + * this endpoint
> + * @flags: flag specifying special usage of request
> + */
> +struct cdns3_request {
> + struct usb_request request;
> + struct cdns3_endpoint *priv_ep;
> + struct cdns3_trb *trb;
> + int start_trb;
> + int end_trb;
> + struct cdns3_aligned_buf *aligned_buf;
> +#define REQUEST_PENDING BIT(0)
> +#define REQUEST_INTERNAL BIT(1)
> +#define REQUEST_INTERNAL_CH BIT(2)
> +#define REQUEST_ZLP BIT(3)
> +#define REQUEST_UNALIGNED BIT(4)
> + u32 flags;
> + struct list_head list;
> +};
> +
> +#define to_cdns3_request(r) (container_of(r, struct cdns3_request, request))
> +
> +/*Stages used during enumeration process.*/
> +#define CDNS3_SETUP_STAGE 0x0
> +#define CDNS3_DATA_STAGE 0x1
> +#define CDNS3_STATUS_STAGE 0x2
> +
> +/**
> + * struct cdns3_device - represent USB device.
> + * @dev: pointer to device structure associated whit this controller
> + * @sysdev: pointer to the DMA capable device
> + * @gadget: device side representation of the peripheral controller
> + * @gadget_driver: pointer to the gadget driver
> + * @dev_ver: device controller version.
> + * @lock: for synchronizing
> + * @regs: base address for device side registers
> + * @setup_buf: used while processing usb control requests
> + * @setup_dma: dma address for setup_buf
> + * @zlp_buf - zlp buffer
> + * @ep0_stage: ep0 stage during enumeration process.
> + * @ep0_data_dir: direction for control transfer
> + * @eps: array of pointers to all endpoints with exclusion ep0
> + * @aligned_buf_list: list of aligned buffers internally allocated by driver
> + * @run_garbage_colector: infroms that at least one element of aligned_buf_list
> + * can be freed
> + * @selected_ep: actually selected endpoint. It's used only to improve
> + * performance.
> + * @isoch_delay: value from Set Isoch Delay request. Only valid on SS/SSP.
> + * @u1_allowed: allow device transition to u1 state
> + * @u2_allowed: allow device transition to u2 state
> + * @is_selfpowered: device is self powered
> + * @setup_pending: setup packet is processing by gadget driver
> + * @hw_configured_flag: hardware endpoint configuration was set.
> + * @wake_up_flag: allow device to remote up the host
> + * @status_completion_no_call: indicate that driver is waiting for status s
> + * stage completion. It's used in deferred SET_CONFIGURATION request.
> + * @onchip_mem_allocated_size: actual size of on-chip memory assigned
> + * to endpoints
> + * @pending_status_wq: workqueue handling status stage for deferred requests.
> + * @shadow_ep_en: hold information about endpoints that will be enabled
> + * in soft irq.
> + * @pending_status_request: request for which status stage was deferred
> + */
> +struct cdns3_device {
> + struct device *dev;
> + struct device *sysdev;
> +
> + struct usb_gadget gadget;
> + struct usb_gadget_driver *gadget_driver;
> +
> +#define CDNS_REVISION_V0 0x00024501
> +#define CDNS_REVISION_V1 0x00024509
> + u32 dev_ver;
> +
> + /* generic spin-lock for drivers */
> + spinlock_t lock;
> +
> + struct cdns3_usb_regs __iomem *regs;
> +
> + struct usb_ctrlrequest *setup_buf;
> + dma_addr_t setup_dma;
> + void *zlp_buf;
> +
> + u8 ep0_stage;
> + int ep0_data_dir;
> +
> + struct cdns3_endpoint *eps[CDNS3_ENDPOINTS_MAX_COUNT];
> +
> + struct list_head aligned_buf_list;
> + unsigned run_garbage_colector:1;
> +
> + u32 selected_ep;
> + u16 isoch_delay;
> +
> + unsigned wait_for_setup:1;
> + unsigned u1_allowed:1;
> + unsigned u2_allowed:1;
> + unsigned is_selfpowered:1;
> + unsigned setup_pending:1;
> + int hw_configured_flag:1;
> + int wake_up_flag:1;
> + unsigned status_completion_no_call:1;
> + int out_mem_is_allocated;
> +
> + struct work_struct pending_status_wq;
> + struct usb_request *pending_status_request;
> + u32 shadow_ep_en;
> + /*in KB */
> + int onchip_mem_allocated_size;
> +};
> +
> +void cdns3_set_register_bit(void __iomem *ptr, u32 mask);
> +dma_addr_t cdns3_trb_virt_to_dma(struct cdns3_endpoint *priv_ep,
> + struct cdns3_trb *trb);
> +enum usb_device_speed cdns3_get_speed(struct cdns3_device *priv_dev);
> +void cdns3_pending_setup_status_handler(struct work_struct *work);
> +void cdns3_hw_reset_eps_config(struct cdns3_device *priv_dev);
> +void cdns3_set_hw_configuration(struct cdns3_device *priv_dev);
> +void cdns3_select_ep(struct cdns3_device *priv_dev, u32 ep);
> +void cdns3_allow_enable_l1(struct cdns3_device *priv_dev, int enable);
> +struct usb_request *cdns3_next_request(struct list_head *list);
> +int cdns3_ep_run_transfer(struct cdns3_endpoint *priv_ep,
> + struct usb_request *request);
> +void cdns3_rearm_transfer(struct cdns3_endpoint *priv_ep, u8 rearm);
> +int cdns3_allocate_trb_pool(struct cdns3_endpoint *priv_ep);
> +u8 cdns3_ep_addr_to_index(u8 ep_addr);
> +int cdns3_gadget_ep_set_wedge(struct usb_ep *ep);
> +int cdns3_gadget_ep_set_halt(struct usb_ep *ep, int value);
> +struct usb_request *cdns3_gadget_ep_alloc_request(struct usb_ep *ep,
> + gfp_t gfp_flags);
> +void cdns3_gadget_ep_free_request(struct usb_ep *ep,
> + struct usb_request *request);
> +int cdns3_gadget_ep_dequeue(struct usb_ep *ep, struct usb_request *request);
> +void cdns3_gadget_giveback(struct cdns3_endpoint *priv_ep,
> + struct cdns3_request *priv_req,
> + int status);
> +
> +int cdns3_init_ep0(struct cdns3_device *priv_dev,
> + struct cdns3_endpoint *priv_ep);
> +void cdns3_ep0_config(struct cdns3_device *priv_dev);
> +void cdns3_ep_config(struct cdns3_endpoint *priv_ep);
> +void cdns3_check_ep0_interrupt_proceed(struct cdns3_device *priv_dev, int dir);
> +int __cdns3_gadget_wakeup(struct cdns3_device *priv_dev);
> +
> +#endif /* __LINUX_CDNS3_GADGET */
> diff --git a/drivers/usb/cdns3/host-export.h b/drivers/usb/cdns3/host-export.h
> new file mode 100644
> index 000000000000..b498a170b7e8
> --- /dev/null
> +++ b/drivers/usb/cdns3/host-export.h
> @@ -0,0 +1,28 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Cadence USBSS DRD Driver - Host Export APIs
> + *
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <peter.chen@xxxxxxx>
> + */
> +#ifndef __LINUX_CDNS3_HOST_EXPORT
> +#define __LINUX_CDNS3_HOST_EXPORT
> +
> +#ifdef CONFIG_USB_CDNS3_HOST
> +
> +int cdns3_host_init(struct cdns3 *cdns);
> +void cdns3_host_exit(struct cdns3 *cdns);
> +
> +#else
> +
> +static inline int cdns3_host_init(struct cdns3 *cdns)
> +{
> + return -ENXIO;
> +}
> +
> +static inline void cdns3_host_exit(struct cdns3 *cdns) { }
> +
> +#endif /* CONFIG_USB_CDNS3_HOST */
> +
> +#endif /* __LINUX_CDNS3_HOST_EXPORT */
> diff --git a/drivers/usb/cdns3/host.c b/drivers/usb/cdns3/host.c
> new file mode 100644
> index 000000000000..df41ba7c6726
> --- /dev/null
> +++ b/drivers/usb/cdns3/host.c
> @@ -0,0 +1,76 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS DRD Driver - host side
> + *
> + * Copyright (C) 2018 Cadence Design Systems.
> + * Copyright (C) 2017-2018 NXP
> + *
> + * Authors: Peter Chen <peter.chen@xxxxxxx>
> + * Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +
> +#include <linux/platform_device.h>
> +#include "core.h"
> +#include "drd.h"
> +
> +static int __cdns3_host_init(struct cdns3 *cdns)
> +{
> + struct platform_device *xhci;
> + int ret;
> +
> + cdns3_drd_switch_host(cdns, 1);
> +
> + xhci = platform_device_alloc("xhci-hcd", PLATFORM_DEVID_AUTO);
> + if (!xhci) {
> + dev_err(cdns->dev, "couldn't allocate xHCI device\n");
> + return -ENOMEM;
> + }
> +
> + xhci->dev.parent = cdns->dev;
> + cdns->host_dev = xhci;
> +
> + ret = platform_device_add_resources(xhci, cdns->xhci_res,
> + CDNS3_XHCI_RESOURCES_NUM);
> + if (ret) {
> + dev_err(cdns->dev, "couldn't add resources to xHCI device\n");
> + goto err1;
> + }
> +
> + ret = platform_device_add(xhci);
> + if (ret) {
> + dev_err(cdns->dev, "failed to register xHCI device\n");
> + goto err1;
> + }
> +
> + return 0;
> +err1:
> + platform_device_put(xhci);
> + return ret;
> +}
> +
> +static void cdns3_host_exit(struct cdns3 *cdns)
> +{
> + platform_device_unregister(cdns->host_dev);
> + cdns->host_dev = NULL;
> + cdns3_drd_switch_host(cdns, 0);
> +}
> +
> +int cdns3_host_init(struct cdns3 *cdns)
> +{
> + struct cdns3_role_driver *rdrv;
> +
> + rdrv = devm_kzalloc(cdns->dev, sizeof(*rdrv), GFP_KERNEL);
> + if (!rdrv)
> + return -ENOMEM;
> +
> + rdrv->start = __cdns3_host_init;
> + rdrv->stop = cdns3_host_exit;
> + rdrv->state = CDNS3_ROLE_STATE_INACTIVE;
> + rdrv->suspend = NULL;
> + rdrv->resume = NULL;
> + rdrv->name = "host";
> +
> + cdns->roles[CDNS3_ROLE_HOST] = rdrv;
> +
> + return 0;
> +}
> diff --git a/drivers/usb/cdns3/trace.c b/drivers/usb/cdns3/trace.c
> new file mode 100644
> index 000000000000..9431eb86d4ff
> --- /dev/null
> +++ b/drivers/usb/cdns3/trace.c
> @@ -0,0 +1,23 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * USBSS device controller driver Trace Support
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +
> +#define CREATE_TRACE_POINTS
> +#include "trace.h"
> +
> +void cdns3_dbg(struct cdns3_device *priv_dev, const char *fmt, ...)
> +{
> + struct va_format vaf;
> + va_list args;
> +
> + va_start(args, fmt);
> + vaf.fmt = fmt;
> + vaf.va = &args;
> + trace_cdns3_log(priv_dev, &vaf);
> + va_end(args);
> +}
> diff --git a/drivers/usb/cdns3/trace.h b/drivers/usb/cdns3/trace.h
> new file mode 100644
> index 000000000000..cc18deca7eec
> --- /dev/null
> +++ b/drivers/usb/cdns3/trace.h
> @@ -0,0 +1,447 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * USBSS device controller driver.
> + * Trace support header file.
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@xxxxxxxxxxx>
> + */
> +
> +#undef TRACE_SYSTEM
> +#define TRACE_SYSTEM cdns3
> +
> +#if !defined(__LINUX_CDNS3_TRACE) || defined(TRACE_HEADER_MULTI_READ)
> +#define __LINUX_CDNS3_TRACE
> +
> +#include <linux/types.h>
> +#include <linux/tracepoint.h>
> +#include <asm/byteorder.h>
> +#include <linux/usb/ch9.h>
> +#include "core.h"
> +#include "gadget.h"
> +#include "debug.h"
> +
> +#define CDNS3_MSG_MAX 500
> +
> +TRACE_EVENT(cdns3_log,
> + TP_PROTO(struct cdns3_device *priv_dev, struct va_format *vaf),
> + TP_ARGS(priv_dev, vaf),
> + TP_STRUCT__entry(
> + __string(name, dev_name(priv_dev->dev))
> + __dynamic_array(char, msg, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __assign_str(name, dev_name(priv_dev->dev));
> + vsnprintf(__get_str(msg), CDNS3_MSG_MAX, vaf->fmt, *vaf->va);
> + ),
> + TP_printk("%s: %s", __get_str(name), __get_str(msg))
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_doorbell,
> + TP_PROTO(const char *ep_name, u32 ep_trbaddr),
> + TP_ARGS(ep_name, ep_trbaddr),
> + TP_STRUCT__entry(
> + __string(name, ep_name)
> + __field(u32, ep_trbaddr)
> + ),
> + TP_fast_assign(
> + __assign_str(name, ep_name);
> + __entry->ep_trbaddr = ep_trbaddr;
> + ),
> + TP_printk("//Ding Dong %s, ep_trbaddr %08x", __get_str(name),
> + __entry->ep_trbaddr)
> +);
> +
> +DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_ep0,
> + TP_PROTO(const char *ep_name, u32 ep_trbaddr),
> + TP_ARGS(ep_name, ep_trbaddr)
> +);
> +
> +DEFINE_EVENT(cdns3_log_doorbell, cdns3_doorbell_epx,
> + TP_PROTO(const char *ep_name, u32 ep_trbaddr),
> + TP_ARGS(ep_name, ep_trbaddr)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_usb_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
> + TP_ARGS(priv_dev, usb_ists),
> + TP_STRUCT__entry(
> + __field(enum usb_device_speed, speed)
> + __field(u32, usb_ists)
> + __dynamic_array(char, str, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __entry->speed = cdns3_get_speed(priv_dev);
> + __entry->usb_ists = usb_ists;
> + ),
> + TP_printk("%s", cdns3_decode_usb_irq(__get_str(str), __entry->speed,
> + __entry->usb_ists))
> +);
> +
> +DEFINE_EVENT(cdns3_log_usb_irq, cdns3_usb_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 usb_ists),
> + TP_ARGS(priv_dev, usb_ists)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_epx_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_dev, priv_ep),
> + TP_STRUCT__entry(
> + __string(ep_name, priv_ep->name)
> + __field(u32, ep_sts)
> + __field(u32, ep_traddr)
> + __dynamic_array(char, str, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __assign_str(ep_name, priv_ep->name);
> + __entry->ep_sts = readl(&priv_dev->regs->ep_sts);
> + __entry->ep_traddr = readl(&priv_dev->regs->ep_traddr);
> + ),
> + TP_printk("%s, ep_traddr: %08x",
> + cdns3_decode_epx_irq(__get_str(str),
> + __get_str(ep_name),
> + __entry->ep_sts),
> + __entry->ep_traddr)
> +);
> +
> +DEFINE_EVENT(cdns3_log_epx_irq, cdns3_epx_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_dev, priv_ep)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ep0_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 ep_sts),
> + TP_ARGS(priv_dev, ep_sts),
> + TP_STRUCT__entry(
> + __field(int, ep_dir)
> + __field(u32, ep_sts)
> + __dynamic_array(char, str, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __entry->ep_dir = priv_dev->ep0_data_dir;
> + __entry->ep_sts = ep_sts;
> + ),
> + TP_printk("%s", cdns3_decode_ep0_irq(__get_str(str),
> + __entry->ep_dir,
> + __entry->ep_sts))
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep0_irq, cdns3_ep0_irq,
> + TP_PROTO(struct cdns3_device *priv_dev, u32 ep_sts),
> + TP_ARGS(priv_dev, ep_sts)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ctrl,
> + TP_PROTO(struct usb_ctrlrequest *ctrl),
> + TP_ARGS(ctrl),
> + TP_STRUCT__entry(
> + __field(u8, bRequestType)
> + __field(u8, bRequest)
> + __field(u16, wValue)
> + __field(u16, wIndex)
> + __field(u16, wLength)
> + __dynamic_array(char, str, CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + __entry->bRequestType = ctrl->bRequestType;
> + __entry->bRequest = ctrl->bRequest;
> + __entry->wValue = le16_to_cpu(ctrl->wValue);
> + __entry->wIndex = le16_to_cpu(ctrl->wIndex);
> + __entry->wLength = le16_to_cpu(ctrl->wLength);
> + ),
> + TP_printk("%s", usb_decode_ctrl(__get_str(str), CDNS3_MSG_MAX,
> + __entry->bRequestType,
> + __entry->bRequest, __entry->wValue,
> + __entry->wIndex, __entry->wLength)
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_ctrl, cdns3_ctrl_req,
> + TP_PROTO(struct usb_ctrlrequest *ctrl),
> + TP_ARGS(ctrl)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req),
> + TP_STRUCT__entry(
> + __string(name, req->priv_ep->name)
> + __field(struct cdns3_request *, req)
> + __field(void *, buf)
> + __field(unsigned int, actual)
> + __field(unsigned int, length)
> + __field(int, status)
> + __field(int, zero)
> + __field(int, short_not_ok)
> + __field(int, no_interrupt)
> + __field(int, start_trb)
> + __field(int, end_trb)
> + __field(struct cdns3_trb *, start_trb_addr)
> + __field(int, flags)
> + ),
> + TP_fast_assign(
> + __assign_str(name, req->priv_ep->name);
> + __entry->req = req;
> + __entry->buf = req->request.buf;
> + __entry->actual = req->request.actual;
> + __entry->length = req->request.length;
> + __entry->status = req->request.status;
> + __entry->zero = req->request.zero;
> + __entry->short_not_ok = req->request.short_not_ok;
> + __entry->no_interrupt = req->request.no_interrupt;
> + __entry->start_trb = req->start_trb;
> + __entry->end_trb = req->end_trb;
> + __entry->start_trb_addr = req->trb;
> + __entry->flags = req->flags;
> + ),
> + TP_printk("%s: req: %p, req buff %p, length: %u/%u %s%s%s, status: %d,"
> + " trb: [start:%d, end:%d: virt addr %pa], flags:%x ",
> + __get_str(name), __entry->req, __entry->buf, __entry->actual,
> + __entry->length,
> + __entry->zero ? "zero | " : "",
> + __entry->short_not_ok ? "short | " : "",
> + __entry->no_interrupt ? "no int" : "",
> + __entry->status,
> + __entry->start_trb,
> + __entry->end_trb,
> + __entry->start_trb_addr,
> + __entry->flags
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_alloc_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_free_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_ep_queue,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_ep_dequeue,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_request, cdns3_gadget_giveback,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_aligned_request,
> + TP_PROTO(struct cdns3_request *priv_req),
> + TP_ARGS(priv_req),
> + TP_STRUCT__entry(
> + __string(name, priv_req->priv_ep->name)
> + __field(struct usb_request *, req)
> + __field(void *, buf)
> + __field(dma_addr_t, dma)
> + __field(void *, aligned_buf)
> + __field(dma_addr_t, aligned_dma)
> + __field(u32, aligned_buf_size)
> + ),
> + TP_fast_assign(
> + __assign_str(name, priv_req->priv_ep->name);
> + __entry->req = &priv_req->request;
> + __entry->buf = priv_req->request.buf;
> + __entry->dma = priv_req->request.dma;
> + __entry->aligned_buf = priv_req->aligned_buf->buf;
> + __entry->aligned_dma = priv_req->aligned_buf->dma;
> + __entry->aligned_buf_size = priv_req->aligned_buf->size;
> + ),
> + TP_printk("%s: req: %p, req buf %p, dma %08llx a_buf %p a_dma %08llx, size %d",
> + __get_str(name), __entry->req, __entry->buf, __entry->dma,
> + __entry->aligned_buf, __entry->aligned_dma,
> + __entry->aligned_buf_size
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_aligned_request, cdns3_free_aligned_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DEFINE_EVENT(cdns3_log_aligned_request, cdns3_prepare_aligned_request,
> + TP_PROTO(struct cdns3_request *req),
> + TP_ARGS(req)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb),
> + TP_STRUCT__entry(
> + __string(name, priv_ep->name)
> + __field(struct cdns3_trb *, trb)
> + __field(u32, buffer)
> + __field(u32, length)
> + __field(u32, control)
> + __field(u32, type)
> + ),
> + TP_fast_assign(
> + __assign_str(name, priv_ep->name);
> + __entry->trb = trb;
> + __entry->buffer = trb->buffer;
> + __entry->length = trb->length;
> + __entry->control = trb->control;
> + __entry->type = usb_endpoint_type(priv_ep->endpoint.desc);
> + ),
> + TP_printk("%s: trb %p, dma buf: 0x%08x, size: %ld, burst: %d ctrl: 0x%08x (%s%s%s%s%s%s%s)",
> + __get_str(name), __entry->trb, __entry->buffer,
> + TRB_LEN(__entry->length),
> + (u8)TRB_BURST_LEN_GET(__entry->length),
> + __entry->control,
> + __entry->control & TRB_CYCLE ? "C=1, " : "C=0, ",
> + __entry->control & TRB_TOGGLE ? "T=1, " : "T=0, ",
> + __entry->control & TRB_ISP ? "ISP, " : "",
> + __entry->control & TRB_FIFO_MODE ? "FIFO, " : "",
> + __entry->control & TRB_CHAIN ? "CHAIN, " : "",
> + __entry->control & TRB_IOC ? "IOC, " : "",
> + TRB_FIELD_TO_TYPE(__entry->control) == TRB_NORMAL ? "Normal" : "LINK"
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_trb, cdns3_prepare_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb)
> +);
> +
> +DEFINE_EVENT(cdns3_log_trb, cdns3_complete_trb,
> + TP_PROTO(struct cdns3_endpoint *priv_ep, struct cdns3_trb *trb),
> + TP_ARGS(priv_ep, trb)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ring,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep),
> + TP_STRUCT__entry(
> + __dynamic_array(u8, ring, TRB_RING_SIZE)
> + __dynamic_array(u8, priv_ep, sizeof(struct cdns3_endpoint))
> + __dynamic_array(char, buffer,
> + (TRBS_PER_SEGMENT * 65) + CDNS3_MSG_MAX)
> + ),
> + TP_fast_assign(
> + memcpy(__get_dynamic_array(priv_ep), priv_ep,
> + sizeof(struct cdns3_endpoint));
> + memcpy(__get_dynamic_array(ring), priv_ep->trb_pool,
> + TRB_RING_SIZE);
> + ),
> +
> + TP_printk("%s",
> + cdns3_dbg_ring((struct cdns3_endpoint *)__get_str(priv_ep),
> + (struct cdns3_trb *)__get_str(ring),
> + __get_str(buffer)))
> +);
> +
> +DEFINE_EVENT(cdns3_log_ring, cdns3_ring,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_ep,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep),
> + TP_STRUCT__entry(
> + __string(name, priv_ep->name)
> + __field(unsigned int, maxpacket)
> + __field(unsigned int, maxpacket_limit)
> + __field(unsigned int, max_streams)
> + __field(unsigned int, maxburst)
> + __field(unsigned int, flags)
> + __field(unsigned int, dir)
> + __field(u8, enqueue)
> + __field(u8, dequeue)
> + ),
> + TP_fast_assign(
> + __assign_str(name, priv_ep->name);
> + __entry->maxpacket = priv_ep->endpoint.maxpacket;
> + __entry->maxpacket_limit = priv_ep->endpoint.maxpacket_limit;
> + __entry->max_streams = priv_ep->endpoint.max_streams;
> + __entry->maxburst = priv_ep->endpoint.maxburst;
> + __entry->flags = priv_ep->flags;
> + __entry->dir = priv_ep->dir;
> + __entry->enqueue = priv_ep->enqueue;
> + __entry->dequeue = priv_ep->dequeue;
> + ),
> + TP_printk("%s: mps: %d/%d. streams: %d, burst: %d, enq idx: %d, "
> + "deq idx: %d, flags %s%s%s%s%s%s%s%s, dir: %s",
> + __get_str(name), __entry->maxpacket,
> + __entry->maxpacket_limit, __entry->max_streams,
> + __entry->maxburst, __entry->enqueue,
> + __entry->dequeue,
> + __entry->flags & EP_ENABLED ? "EN | " : "",
> + __entry->flags & EP_STALL ? "STALL | " : "",
> + __entry->flags & EP_WEDGE ? "WEDGE | " : "",
> + __entry->flags & EP_TRANSFER_STARTED ? "STARTED | " : "",
> + __entry->flags & EP_UPDATE_EP_TRBADDR ? "UPD TRB | " : "",
> + __entry->flags & EP_PENDING_REQUEST ? "REQ PEN | " : "",
> + __entry->flags & EP_RING_FULL ? "RING FULL |" : "",
> + __entry->flags & EP_CLAIMED ? "CLAIMED " : "",
> + __entry->dir ? "IN" : "OUT"
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_enable,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DEFINE_EVENT(cdns3_log_ep, cdns3_gadget_ep_disable,
> + TP_PROTO(struct cdns3_endpoint *priv_ep),
> + TP_ARGS(priv_ep)
> +);
> +
> +DECLARE_EVENT_CLASS(cdns3_log_request_handled,
> + TP_PROTO(struct cdns3_request *priv_req, int current_index,
> + int handled),
> + TP_ARGS(priv_req, current_index, handled),
> + TP_STRUCT__entry(
> + __field(struct cdns3_request *, priv_req)
> + __field(unsigned int, dma_position)
> + __field(unsigned int, handled)
> + __field(unsigned int, dequeue_idx)
> + __field(unsigned int, enqueue_idx)
> + __field(unsigned int, start_trb)
> + __field(unsigned int, end_trb)
> + ),
> + TP_fast_assign(
> + __entry->priv_req = priv_req;
> + __entry->dma_position = current_index;
> + __entry->handled = handled;
> + __entry->dequeue_idx = priv_req->priv_ep->dequeue;
> + __entry->enqueue_idx = priv_req->priv_ep->enqueue;
> + __entry->start_trb = priv_req->start_trb;
> + __entry->end_trb = priv_req->end_trb;
> + ),
> + TP_printk("Req: %p %s, DMA pos: %d, ep deq: %d, ep enq: %d,"
> + " start trb: %d, end trb: %d",
> + __entry->priv_req,
> + __entry->handled ? "handled" : "not handled",
> + __entry->dma_position, __entry->dequeue_idx,
> + __entry->enqueue_idx, __entry->start_trb,
> + __entry->end_trb
> + )
> +);
> +
> +DEFINE_EVENT(cdns3_log_request_handled, cdns3_request_handled,
> + TP_PROTO(struct cdns3_request *priv_req, int current_index,
> + int handled),
> + TP_ARGS(priv_req, current_index, handled)
> +);
> +#endif /* __LINUX_CDNS3_TRACE */
> +
> +/* this part must be outside header guard */
> +
> +#undef TRACE_INCLUDE_PATH
> +#define TRACE_INCLUDE_PATH .
> +
> +#undef TRACE_INCLUDE_FILE
> +#define TRACE_INCLUDE_FILE trace
> +
> +#include <trace/define_trace.h>
> --
> 2.17.1
>

Next message: Viresh Kumar: "Re: [RFC v2 02/11] OPP: Make dev_pm_opp_set_rate() with freq=0 as valid"
Previous message: Christoph Hellwig: "Re: [PATCH 09/22] memremap: lift the devmap_enable manipulation into devm_memremap_pages"
In reply to: Heikki Krogerus: "Re: [PATCH v7 5/6] usb:cdns3 Add Cadence USB3 DRD Driver"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]