Re: [PATCH v2] riscv: dts: Add DT node for SiFive FU540 Ethernet controller driver

[Troy Benjegerdes]

> On Jun 21, 2019, at 2:14 PM, Atish Patra <Atish.Patra@xxxxxxx> wrote:
> 
> On Fri, 2019-06-21 at 16:23 +0530, Yash Shah wrote:
>> DT node for SiFive FU540-C000 GEMGXL Ethernet controller driver added
>> 
>> Signed-off-by: Yash Shah <yash.shah@xxxxxxxxxx>
>> ---
>> arch/riscv/boot/dts/sifive/fu540-c000.dtsi          | 16
>> ++++++++++++++++
>> arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts |  9 +++++++++
>> 2 files changed, 25 insertions(+)
>> 
>> diff --git a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
>> b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
>> index 4e8fbde..c53b4ea 100644
>> --- a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
>> +++ b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi
>> @@ -225,5 +225,21 @@
>> 			#address-cells = <1>;
>> 			#size-cells = <0>;
>> 		};
>> +		eth0: ethernet@10090000 {
>> +			compatible = "sifive,fu540-macb";
>> +			interrupt-parent = <&plic0>;
>> +			interrupts = <53>;
>> +			reg = <0x0 0x10090000 0x0 0x2000
>> +			       0x0 0x100a0000 0x0 0x1000>;
>> +			reg-names = "control";
>> +			status = "disabled";
>> +			local-mac-address = [00 00 00 00 00 00];
>> +			clock-names = "pclk", "hclk";
>> +			clocks = <&prci PRCI_CLK_GEMGXLPLL>,
>> +				 <&prci PRCI_CLK_GEMGXLPLL>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +		};
>> +
>> 	};
>> };
>> diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
>> b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
>> index 4da8870..d783bf2 100644
>> --- a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
>> +++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts
>> @@ -63,3 +63,12 @@
>> 		disable-wp;
>> 	};
>> };
>> +
>> +&eth0 {
>> +	status = "okay";
>> +	phy-mode = "gmii";
>> +	phy-handle = <&phy1>;
>> +	phy1: ethernet-phy@0 {
>> +		reg = <0>;
>> +	};
>> +};
> 
> Thanks. I am able to boot Unleashed with networking enabled with this
> patch.
> 
> FWIW, 
> Tested-by: Atish Patra <atish.patra@xxxxxxx>
> 
> Regards,
> Atish

I am able to boot using a build from the dev/new-dts branch of
my freedom-u-sdk development tree [1] which has this patch
with an additional reset-gpios entry for the ethernet phy in the
DTS provided by the legacy U-boot[2].

Tested-by: Troy Benjegerdes <troy.benjegerdes@xxxxxxxxxx>

[1] https://github.com/tmagik/freedom-u-sdk 
[2] https://github.com/sifive/HiFive_U-Boot/blob/081373fa3eb0ca79ba3f4a703e8e83a15135a6d1/arch/riscv/dts/hifive_u540.dts#L73