[PATCH v2] rtl8xxxu: Fix wifi low signal strength issue of RTL8723BU

[Chris Chiu]

The WiFi tx power of RTL8723BU is extremely low after booting. So
the WiFi scan gives very limited AP list and it always fails to
connect to the selected AP. This module only supports 1x1 antenna
and the antenna is switched to bluetooth due to some incorrect
register settings.

Compare with the vendor driver https://github.com/lwfinger/rtl8723bu,
we realized that the 8723bu's enable_rf() does the same thing as
rtw_btcoex_HAL_Initialize() in vendor driver. And it by default
sets the antenna path to BTC_ANT_PATH_BT which we verified it's
the cause of the wifi weak tx power. The vendor driver will set
the antenna path to BTC_ANT_PATH_PTA in the consequent btcoexist
mechanism, by the function halbtc8723b1ant_PsTdma.

This commit hand over the antenna control to PTA(Packet Traffic
Arbitration), which compares the weight of bluetooth/wifi traffic
then determine whether to continue current wifi traffic or not.
After PTA take control, The wifi signal will be back to normal and
the bluetooth scan can also work at the same time. However, the
btcoexist still needs to be handled under different circumstances.
If there's a BT connection established, the wifi still fails to
connect until BT disconnected.

Signed-off-by: Chris Chiu <chiu@xxxxxxxxxxxx>
---


Note:
 v2:
  - Replace BIT(11) with the descriptive definition
  - Meaningful comment for the REG_S0S1_PATH_SWITCH setting


 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c | 11 ++++++++---
 drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c  |  3 ++-
 2 files changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c
index 3adb1d3d47ac..ceffe05bd65b 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c
@@ -1525,7 +1525,7 @@ static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv)
 	/*
 	 * WLAN action by PTA
 	 */
-	rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04);
+	rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x0c);
 
 	/*
 	 * BT select S0/S1 controlled by WiFi
@@ -1568,9 +1568,14 @@ static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv)
 	rtl8xxxu_gen2_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv));
 
 	/*
-	 * 0x280, 0x00, 0x200, 0x80 - not clear
+	 * Different settings per different antenna position.
+	 *      Antenna Position:   | Normal   Inverse
+	 * --------------------------------------------------
+	 * Antenna switch to BT:    |  0x280,   0x00
+	 * Antenna switch to WiFi:  |  0x0,     0x280
+	 * Antenna switch to PTA:   |  0x200,   0x80
 	 */
-	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00);
+	rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x80);
 
 	/*
 	 * Software control, antenna at WiFi side
diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
index 8136e268b4e6..c6c41fb962ff 100644
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c
@@ -3891,12 +3891,13 @@ static int rtl8xxxu_init_device(struct ieee80211_hw *hw)
 
 	/* Check if MAC is already powered on */
 	val8 = rtl8xxxu_read8(priv, REG_CR);
+	val16 = rtl8xxxu_read16(priv, REG_SYS_CLKR);
 
 	/*
 	 * Fix 92DU-VC S3 hang with the reason is that secondary mac is not
 	 * initialized. First MAC returns 0xea, second MAC returns 0x00
 	 */
-	if (val8 == 0xea)
+	if (val8 == 0xea || !(val16 & SYS_CLK_MAC_CLK_ENABLE))
 		macpower = false;
 	else
 		macpower = true;
-- 
2.11.0