Re: [PATCH v7 10/14] dt-bindings: Document the Rockchip ISP1 bindings

[Andrà Almeida]

Hello Helen,

On 7/3/19 4:09 PM, Helen Koike wrote:
> From: Jacob Chen <jacob2.chen@xxxxxxxxxxxxxx>
>
> Add DT bindings documentation for Rockchip ISP1
>
> Signed-off-by: Jacob Chen <jacob2.chen@xxxxxxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> [update for upstream]
> Signed-off-by: Helen Koike <helen.koike@xxxxxxxxxxxxx>
>
> ---
>
> Changes in v7:
> - update document with new design and tested example
>
>  .../bindings/media/rockchip-isp1.txt          | 71 +++++++++++++++++++
>  1 file changed, 71 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/rockchip-isp1.txt
>
> diff --git a/Documentation/devicetree/bindings/media/rockchip-isp1.txt b/Documentation/devicetree/bindings/media/rockchip-isp1.txt
> new file mode 100644
> index 000000000000..a97fef0f189f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/rockchip-isp1.txt
> @@ -0,0 +1,71 @@
> +Rockchip SoC Image Signal Processing unit v1
> +----------------------------------------------
> +
> +Rockchip ISP1 is the Camera interface for the Rockchip series of SoCs
> +which contains image processing, scaling, and compression funcitons.
> +
> +Required properties:
> +- compatible: value should be one of the following
> +	"rockchip,rk3288-cif-isp";
> +	"rockchip,rk3399-cif-isp";
> +- reg : offset and length of the register set for the device.
> +- interrupts: should contain ISP interrupt.
> +- clocks: phandle to the required clocks.
> +- clock-names: required clock name.
> +- iommus: required a iommu node.
> +- phys: the phandle for the PHY port
> +- phy-names: must contain "dphy"
> +
> +port node
> +-------------------
I would remove those extra `---`, and keep as:
...node
...----

The same applies for the title.

Thanks,
ÂÂÂ AndrÃ

> +
> +The device node should contain one 'ports' child node, with children 'port'
> +with child 'endpoint'.
> +nodes, according to the bindings defined in Documentation/devicetree/bindings/
> +media/video-interfaces.txt.
> +
> +- endpoint(mipi):
> +	- remote-endpoint: Connecting to Rockchip MIPI-DPHY,
> +		which is defined in rockchip-mipi-dphy.txt.
> +
> +The port node must contain at least one endpoint, either parallel or mipi.
> +It could have multiple endpoints, but please note the hardware don't support
> +two sensors work at a time, they are supposed to work asynchronously.
> +
> +Device node example
> +-------------------
> +
> +	isp0: isp0@ff910000 {
> +		compatible = "rockchip,rk3399-cif-isp";
> +		reg = <0x0 0xff910000 0x0 0x4000>;
> +		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>;
> +		clocks = <&cru SCLK_ISP0>,
> +			 <&cru ACLK_ISP0>, <&cru ACLK_ISP0_WRAPPER>,
> +			 <&cru HCLK_ISP0>, <&cru HCLK_ISP0_WRAPPER>;
> +		clock-names = "clk_isp",
> +			      "aclk_isp", "aclk_isp_wrap",
> +			      "hclk_isp", "hclk_isp_wrap";
> +		power-domains = <&power RK3399_PD_ISP0>;
> +		iommus = <&isp0_mmu>;
> +		phys = <&dphy>;
> +		phy-names = "dphy";
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				mipi_in_wcam: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&wcam_out>;
> +					data-lanes = <1 2>;
> +				};
> +
> +				mipi_in_ucam: endpoint@1 {
> +					reg = <1>;
> +					remote-endpoint = <&ucam_out>;
> +					data-lanes = <1>;
> +				};
> +			};
> +		};
> +	};