Re: [PATCH 01/16] net: phy: adin: add support for Analog Devices PHYs

[Ardelean, Alexandru]

On Mon, 2019-08-05 at 22:54 +0200, Heiner Kallweit wrote:
> [External]
> 
> On 05.08.2019 18:54, Alexandru Ardelean wrote:
> > This change adds support for Analog Devices Industrial Ethernet PHYs.
> > Particularly the PHYs this driver adds support for:
> >  * ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
> >  * ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
> >    Ethernet PHY
> > 
> > The 2 chips are pin & register compatible with one another. The main
> > difference being that ADIN1200 doesn't operate in gigabit mode.
> > 
> > The chips can be operated by the Generic PHY driver as well via the
> > standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
> > kernel as well. This assumes that configuration of the PHY has been done
> > required.
> > 
> > Configuration can also be done via registers, which will be implemented by
> > the driver in the next changes.
> > 
> > Datasheets:
> >   https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdf
> >   https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
> > 
> > Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
> > ---
> >  MAINTAINERS              |  7 +++++
> >  drivers/net/phy/Kconfig  |  9 ++++++
> >  drivers/net/phy/Makefile |  1 +
> >  drivers/net/phy/adin.c   | 59 ++++++++++++++++++++++++++++++++++++++++
> >  4 files changed, 76 insertions(+)
> >  create mode 100644 drivers/net/phy/adin.c
> > 
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index ee663e0e2f2e..faf5723610c8 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -938,6 +938,13 @@ S:	Supported
> >  F:	drivers/mux/adgs1408.c
> >  F:	Documentation/devicetree/bindings/mux/adi,adgs1408.txt
> >  
> > +ANALOG DEVICES INC ADIN DRIVER
> > +M:	Alexandru Ardelean <alexaundru.ardelean@xxxxxxxxxx>
> > +L:	netdev@xxxxxxxxxxxxxxx
> > +W:	http://ez.analog.com/community/linux-device-drivers
> > +S:	Supported
> > +F:	drivers/net/phy/adin.c
> > +
> >  ANALOG DEVICES INC ADIS DRIVER LIBRARY
> >  M:	Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
> >  S:	Supported
> > diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> > index 206d8650ee7f..5966d3413676 100644
> > --- a/drivers/net/phy/Kconfig
> > +++ b/drivers/net/phy/Kconfig
> > @@ -257,6 +257,15 @@ config SFP
> >  	depends on HWMON || HWMON=n
> >  	select MDIO_I2C
> >  
> > +config ADIN_PHY
> > +	tristate "Analog Devices Industrial Ethernet PHYs"
> > +	help
> > +	  Adds support for the Analog Devices Industrial Ethernet PHYs.
> > +	  Currently supports the:
> > +	  - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
> > +	  - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
> > +	    Ethernet PHY
> > +
> >  config AMD_PHY
> >  	tristate "AMD PHYs"
> >  	---help---
> > diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
> > index ba07c27e4208..a03437e091f3 100644
> > --- a/drivers/net/phy/Makefile
> > +++ b/drivers/net/phy/Makefile
> > @@ -47,6 +47,7 @@ obj-$(CONFIG_SFP)		+= sfp.o
> >  sfp-obj-$(CONFIG_SFP)		+= sfp-bus.o
> >  obj-y				+= $(sfp-obj-y) $(sfp-obj-m)
> >  
> > +obj-$(CONFIG_ADIN_PHY)		+= adin.o
> >  obj-$(CONFIG_AMD_PHY)		+= amd.o
> >  aquantia-objs			+= aquantia_main.o
> >  ifdef CONFIG_HWMON
> > diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> > new file mode 100644
> > index 000000000000..6a610d4563c3
> > --- /dev/null
> > +++ b/drivers/net/phy/adin.c
> > @@ -0,0 +1,59 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/**
> > + *  Driver for Analog Devices Industrial Ethernet PHYs
> > + *
> > + * Copyright 2019 Analog Devices Inc.
> > + */
> > +#include <linux/kernel.h>
> > +#include <linux/errno.h>
> > +#include <linux/init.h>
> > +#include <linux/module.h>
> > +#include <linux/mii.h>
> > +#include <linux/phy.h>
> > +
> > +#define PHY_ID_ADIN1200				0x0283bc20
> > +#define PHY_ID_ADIN1300				0x0283bc30
> > +
> > +static int adin_config_init(struct phy_device *phydev)
> > +{
> > +	int rc;
> > +
> > +	rc = genphy_config_init(phydev);
> > +	if (rc < 0)
> > +		return rc;
> > +
> > +	return 0;
> > +}
> > +
> > +static struct phy_driver adin_driver[] = {
> > +	{
> > +		.phy_id		= PHY_ID_ADIN1200,
> 
> You could use PHY_ID_MATCH_MODEL here.
> 
> > +		.name		= "ADIN1200",
> > +		.phy_id_mask	= 0xfffffff0,
> > +		.features	= PHY_BASIC_FEATURES,
> 
> Setting features is deprecated, instead the get_features callback
> should be implemented if the default genphy_read_abilities needs
> to be extended / replaced. You say that the PHY's work with the
> genphy driver, so I suppose the default feature detection is ok
> in your case. Then you could simply remove setting "features".

ack;
thanks for the info

> 
> > +		.config_init	= adin_config_init,
> > +		.config_aneg	= genphy_config_aneg,
> > +		.read_status	= genphy_read_status,
> > +	},
> > +	{
> > +		.phy_id		= PHY_ID_ADIN1300,
> > +		.name		= "ADIN1300",
> > +		.phy_id_mask	= 0xfffffff0,
> > +		.features	= PHY_GBIT_FEATURES,
> > +		.config_init	= adin_config_init,
> > +		.config_aneg	= genphy_config_aneg,
> > +		.read_status	= genphy_read_status,
> > +	},
> > +};
> > +
> > +module_phy_driver(adin_driver);
> > +
> > +static struct mdio_device_id __maybe_unused adin_tbl[] = {
> > +	{ PHY_ID_ADIN1200, 0xfffffff0 },
> > +	{ PHY_ID_ADIN1300, 0xfffffff0 },
> 
> PHY_ID_MATCH_MODEL could be used here too.

ack;
will take a look

> 
> > +	{ }
> > +};
> > +
> > +MODULE_DEVICE_TABLE(mdio, adin_tbl);
> > +MODULE_DESCRIPTION("Analog Devices Industrial Ethernet PHY driver");
> > +MODULE_LICENSE("GPL");
> >