[PATCH V15 10/13] dt-bindings: PCI: tegra: Add device tree support for Tegra194

From: Vidya Sagar
Date: Fri Aug 09 2019 - 00:47:30 EST

Next message: Vidya Sagar: "[PATCH V15 11/13] dt-bindings: PHY: P2U: Add Tegra194 P2U block"
Previous message: Bjorn Helgaas: "Re: [PATCH v2 2/2] nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled"
In reply to: Vidya Sagar: "[PATCH V15 09/13] dt-bindings: Add PCIe supports-clkreq property"
Next in thread: Vidya Sagar: "[PATCH V15 11/13] dt-bindings: PHY: P2U: Add Tegra194 P2U block"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Add support for Tegra194 PCIe controllers. These controllers are based
on Synopsys DesignWare core IP.

Signed-off-by: Vidya Sagar <vidyas@xxxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Acked-by: Thierry Reding <treding@xxxxxxxxxx>
---
V15:
* None

V14:
* None

V13:
* None

V12:
* None

V11:
* None

V10:
* None

V9:
* Added Acked-by from Thierry

V8:
* Addressed review comments from Thierry
* Modified DT example to reflect new changes

V7:
* Changed description of the property "nvidia,bpmp".
* Removed property "nvidia,disable-aspm-states".

V6:
* Removed 'max-link-speed' as it is going to be a common sub-system property
* Removed 'nvidia,init-link-speed' as there isn't much value addition
* Removed 'nvidia,wake-gpios' for now
* Addressed review comments from Thierry and Rob in general

V5:
* None

V4:
* None

V3:
* Using only 'Cx' (x-being controller number) format to represent a controller
* Changed to 'value: description' format where applicable
* Changed 'nvidia,init-speed' to 'nvidia,init-link-speed'
* Provided more documentation for 'nvidia,init-link-speed' property
* Changed 'nvidia,pex-wake' to 'nvidia,wake-gpios'

V2:
* Added documentation for 'power-domains' property
* Removed 'window1' and 'window2' properties
* Removed '_clk' and '_rst' from clock and reset names
* Dropped 'pcie' from phy-names
* Added entry for BPMP-FW handle
* Removed offsets for some of the registers and added them in code and would be pickedup based on
controller ID
* Changed 'nvidia,max-speed' to 'max-link-speed' and is made as an optional
* Changed 'nvidia,disable-clock-request' to 'supports-clkreq' with inverted operation
* Added more documentation for 'nvidia,update-fc-fixup' property
* Removed 'nvidia,enable-power-down' and 'nvidia,plat-gpios' properties
* Added '-us' to all properties that represent time in microseconds
* Moved P2U documentation to a separate file

.../bindings/pci/nvidia,tegra194-pcie.txt | 155 ++++++++++++++++++
1 file changed, 155 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt

diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
new file mode 100644
index 000000000000..674e5adb2895
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
@@ -0,0 +1,155 @@
+NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie".
+- device_type: Must be "pci"
+- power-domains: A phandle to the node that controls power to the respective
+ PCIe controller and a specifier name for the PCIe controller. Following are
+ the specifiers for the different PCIe controllers
+ TEGRA194_POWER_DOMAIN_PCIEX8B: C0
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C1
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C2
+ TEGRA194_POWER_DOMAIN_PCIEX1A: C3
+ TEGRA194_POWER_DOMAIN_PCIEX4A: C4
+ TEGRA194_POWER_DOMAIN_PCIEX8A: C5
+ these specifiers are defined in
+ "include/dt-bindings/power/tegra194-powergate.h" file.
+- reg: A list of physical base address and length pairs for each set of
+ controller registers. Must contain an entry for each entry in the reg-names
+ property.
+- reg-names: Must include the following entries:
+ "appl": Controller's application logic registers
+ "config": As per the definition in designware-pcie.txt
+ "atu_dma": iATU and DMA registers. This is where the iATU (internal Address
+ Translation Unit) registers of the PCIe core are made available
+ for SW access.
+ "dbi": The aperture where root port's own configuration registers are
+ available
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+ entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+ "intr": The Tegra interrupt that is asserted for controller interrupts
+ "msi": The Tegra interrupt that is asserted when an MSI is received
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+ - cell 0 specifies the bus and device numbers of the root port:
+ [23:16]: bus number
+ [15:11]: device number
+ - cell 1 denotes the upper 32 address bits and should be 0
+ - cell 2 contains the lower 32 address bits and is used to translate to the
+ CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+ PCI regions. The entries must be 7 cells each, where the first three cells
+ correspond to the address as described for the #address-cells property
+ above, the fourth and fifth cells are for the physical CPU address to
+ translate to and the sixth and seventh cells are as described for the
+ #size-cells property above.
+ - Entries setup the mapping for the standard I/O, memory and
+ prefetchable PCI regions. The first cell determines the type of region
+ that is setup:
+ - 0x81000000: I/O memory region
+ - 0x82000000: non-prefetchable memory region
+ - 0xc2000000: prefetchable memory region
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+ Please refer to the standard PCI bus binding document for a more detailed
+ explanation.
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - core
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - apb
+ - core
+- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
+- phy-names: Must include an entry for each active lane.
+ "p2u-N": where N ranges from 0 to one less than the total number of lanes
+- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed
+ by controller-id. Following are the controller ids for each controller.
+ 0: C0
+ 1: C1
+ 2: C2
+ 3: C3
+ 4: C4
+ 5: C5
+- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals
+
+Optional properties:
+- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt
+- nvidia,update-fc-fixup: This is a boolean property and needs to be present to
+ improve performance when a platform is designed in such a way that it
+ satisfies at least one of the following conditions thereby enabling root
+ port to exchange optimum number of FC (Flow Control) credits with
+ downstream devices
+ 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS)
+ 2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and
+ a) speed is Gen-2 and MPS is 256B
+ b) speed is >= Gen-3 with any MPS
+- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM
+ to be specified in microseconds
+- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be
+ specified in microseconds
+- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be
+ specified in microseconds
+
+Examples:
+=========
+
+Tegra194:
+--------
+
+ pcie@14180000 {
+ compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
+ reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */
+ 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */
+ 0x00 0x38040000 0x0 0x00040000>; /* iATU_DMA reg space (256K) */
+ reg-names = "appl", "config", "atu_dma";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <8>;
+ linux,pci-domain = <0>;
+
+ clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
+ clock-names = "core";
+
+ resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>,
+ <&bpmp TEGRA194_RESET_PEX0_CORE_0>;
+ reset-names = "apb", "core";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+ interrupt-names = "intr", "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ nvidia,bpmp = <&bpmp 0>;
+
+ supports-clkreq;
+ nvidia,aspm-cmrt-us = <60>;
+ nvidia,aspm-pwr-on-t-us = <20>;
+ nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x38100000 0x0 0x38100000 0x0 0x00100000 /* downstream I/O (1MB) */
+ 0x82000000 0x0 0x38200000 0x0 0x38200000 0x0 0x01E00000 /* non-prefetchable memory (30MB) */
+ 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory (16GB) */
+
+ vddio-pex-ctl-supply = <&vdd_1v8ao>;
+
+ phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>,
+ <&p2u_hsio_5>;
+ phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
+ };
--
2.17.1

Next message: Vidya Sagar: "[PATCH V15 11/13] dt-bindings: PHY: P2U: Add Tegra194 P2U block"
Previous message: Bjorn Helgaas: "Re: [PATCH v2 2/2] nvme-pci: Allow PCI bus-level PM to be used if ASPM is disabled"
In reply to: Vidya Sagar: "[PATCH V15 09/13] dt-bindings: Add PCIe supports-clkreq property"
Next in thread: Vidya Sagar: "[PATCH V15 11/13] dt-bindings: PHY: P2U: Add Tegra194 P2U block"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]