Re: [PATCH v3 03/14] net: phy: adin: add support for interrupts

[Heiner Kallweit]

On 09.08.2019 15:35, Alexandru Ardelean wrote:
> This change adds support for enabling PHY interrupts that can be used by
> the PHY framework to get signal for link/speed/auto-negotiation changes.
> 
> Reviewed-by: Andrew Lunn <andrew@xxxxxxx>
> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
> ---
>  drivers/net/phy/adin.c | 38 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> index fc0148ba4b94..91ff26d08fd5 100644
> --- a/drivers/net/phy/adin.c
> +++ b/drivers/net/phy/adin.c
> @@ -14,11 +14,45 @@
>  #define PHY_ID_ADIN1200				0x0283bc20
>  #define PHY_ID_ADIN1300				0x0283bc30
>  
> +#define ADIN1300_INT_MASK_REG			0x0018
> +#define   ADIN1300_INT_MDIO_SYNC_EN		BIT(9)
> +#define   ADIN1300_INT_ANEG_STAT_CHNG_EN	BIT(8)
> +#define   ADIN1300_INT_ANEG_PAGE_RX_EN		BIT(6)
> +#define   ADIN1300_INT_IDLE_ERR_CNT_EN		BIT(5)
> +#define   ADIN1300_INT_MAC_FIFO_OU_EN		BIT(4)
> +#define   ADIN1300_INT_RX_STAT_CHNG_EN		BIT(3)
> +#define   ADIN1300_INT_LINK_STAT_CHNG_EN	BIT(2)
> +#define   ADIN1300_INT_SPEED_CHNG_EN		BIT(1)
> +#define   ADIN1300_INT_HW_IRQ_EN		BIT(0)
> +#define ADIN1300_INT_MASK_EN	\
> +	(ADIN1300_INT_ANEG_STAT_CHNG_EN | ADIN1300_INT_ANEG_PAGE_RX_EN | \
> +	 ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_SPEED_CHNG_EN | \
> +	 ADIN1300_INT_HW_IRQ_EN)

phylib only needs the link status change interrupt. It shouldn't hurt
if enable more interrupt sources, but it's not needed.


> +#define ADIN1300_INT_STATUS_REG			0x0019
> +
>  static int adin_config_init(struct phy_device *phydev)
>  {
>  	return genphy_config_init(phydev);
>  }
>  
> +static int adin_phy_ack_intr(struct phy_device *phydev)
> +{
> +	/* Clear pending interrupts */
> +	int rc = phy_read(phydev, ADIN1300_INT_STATUS_REG);
> +
> +	return rc < 0 ? rc : 0;
> +}
> +
> +static int adin_phy_config_intr(struct phy_device *phydev)
> +{
> +	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
> +		return phy_set_bits(phydev, ADIN1300_INT_MASK_REG,
> +				    ADIN1300_INT_MASK_EN);
> +
> +	return phy_clear_bits(phydev, ADIN1300_INT_MASK_REG,
> +			      ADIN1300_INT_MASK_EN);
> +}
> +
>  static struct phy_driver adin_driver[] = {
>  	{
>  		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200),
> @@ -26,6 +60,8 @@ static struct phy_driver adin_driver[] = {
>  		.config_init	= adin_config_init,
>  		.config_aneg	= genphy_config_aneg,
>  		.read_status	= genphy_read_status,
> +		.ack_interrupt	= adin_phy_ack_intr,
> +		.config_intr	= adin_phy_config_intr,
>  		.resume		= genphy_resume,
>  		.suspend	= genphy_suspend,
>  	},
> @@ -35,6 +71,8 @@ static struct phy_driver adin_driver[] = {
>  		.config_init	= adin_config_init,
>  		.config_aneg	= genphy_config_aneg,
>  		.read_status	= genphy_read_status,
> +		.ack_interrupt	= adin_phy_ack_intr,
> +		.config_intr	= adin_phy_config_intr,
>  		.resume		= genphy_resume,
>  		.suspend	= genphy_suspend,
>  	},
>