[PATCH v3] Bluetooth: btusb: Fix suspend issue for Realtek devices

[Alex Lu]

From: Alex Lu <alex_lu@xxxxxxxxxxxxxx>

>From the perspective of controller, global suspend means there is no
SET_FEATURE (DEVICE_REMOTE_WAKEUP) and controller would drop the
firmware. It would consume less power. So we should not send this kind
of SET_FEATURE when host goes to suspend state.
Otherwise, when making device enter selective suspend, host should send
SET_FEATURE to make sure the firmware remains.

Signed-off-by: Alex Lu <alex_lu@xxxxxxxxxxxxxx>
---
Changes in v3:
  - Change to fit for bluetooth-next
Changes in v2:
  - Change flag to be more descriptive
  - Delete pointless #ifdef CONFIG_BT_HCIBTUSB_RTL and #endif

 drivers/bluetooth/btusb.c | 34 ++++++++++++++++++++++++++++++----
 1 file changed, 30 insertions(+), 4 deletions(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 3876fee6ad13..b606c663ba57 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -435,6 +435,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
 #define BTUSB_OOB_WAKE_ENABLED	11
 #define BTUSB_HW_RESET_ACTIVE	12
 #define BTUSB_TX_WAIT_VND_EVT	13
+#define BTUSB_WAKEUP_DISABLE	14
 
 struct btusb_data {
 	struct hci_dev       *hdev;
@@ -1175,6 +1176,13 @@ static int btusb_open(struct hci_dev *hdev)
 	 */
 	device_wakeup_enable(&data->udev->dev);
 
+	/* Disable device remote wakeup when host is suspended
+	 * For Realtek chips, global suspend without
+	 * SET_FEATURE (DEVICE_REMOTE_WAKEUP) can save more power in device.
+	 */
+	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+		device_wakeup_disable(&data->udev->dev);
+
 	if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
 		goto done;
 
@@ -1238,6 +1246,11 @@ static int btusb_close(struct hci_dev *hdev)
 		goto failed;
 
 	data->intf->needs_remote_wakeup = 0;
+
+	/* Enable remote wake up for auto-suspend */
+	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
+		data->intf->needs_remote_wakeup = 1;
+
 	device_wakeup_disable(&data->udev->dev);
 	usb_autopm_put_interface(data->intf);
 
@@ -3769,11 +3782,11 @@ static int btusb_probe(struct usb_interface *intf,
 		hdev->setup = btrtl_setup_realtek;
 		hdev->shutdown = btrtl_shutdown_realtek;
 
-		/* Realtek devices lose their updated firmware over suspend,
-		 * but the USB hub doesn't notice any status change.
-		 * Explicitly request a device reset on resume.
+		/* Realtek devices lose their updated firmware over global
+		 * suspend that means host doesn't send SET_FEATURE
+		 * (DEVICE_REMOTE_WAKEUP)
 		 */
-		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
+		set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
 	}
 #endif
 
@@ -3947,6 +3960,19 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
 		enable_irq(data->oob_wake_irq);
 	}
 
+	/* For global suspend, Realtek devices lose the loaded fw
+	 * in them. But for autosuspend, firmware should remain.
+	 * Actually, it depends on whether the usb host sends
+	 * set feature (enable wakeup) or not.
+	 */
+	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags)) {
+		if (PMSG_IS_AUTO(message) &&
+		    device_can_wakeup(&data->udev->dev))
+			data->udev->do_remote_wakeup = 1;
+		else if (!PMSG_IS_AUTO(message))
+			data->udev->reset_resume = 1;
+	}
+
 	return 0;
 }
 
-- 
2.19.2