[PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file

[Vinod Koul]

Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
nodes

Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++
 1 file changed, 95 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
new file mode 100644
index 000000000000..4a678be46d37
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: BSD-3-Clause
+// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+// Copyright (c) 2019, Linaro Limited
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+&spmi_bus {
+	pm8150_0: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+		};
+
+		pm8150_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			status = "disabled";
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+
+			status = "disabled";
+		};
+
+		pm8150_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
+				     <0 0xc1 0 IRQ_TYPE_NONE>,
+				     <0 0xc2 0 IRQ_TYPE_NONE>,
+				     <0 0xc3 0 IRQ_TYPE_NONE>,
+				     <0 0xc4 0 IRQ_TYPE_NONE>,
+				     <0 0xc5 0 IRQ_TYPE_NONE>,
+				     <0 0xc6 0 IRQ_TYPE_NONE>,
+				     <0 0xc7 0 IRQ_TYPE_NONE>,
+				     <0 0xc8 0 IRQ_TYPE_NONE>,
+				     <0 0xc9 0 IRQ_TYPE_NONE>,
+				     <0 0xca 0 IRQ_TYPE_NONE>,
+				     <0 0xcb 0 IRQ_TYPE_NONE>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
-- 
2.20.1