RE: [PATCH 10/14] serial: tegra: add support to use 8 bytes trigger
From: Krishna Yarlagadda
Date: Tue Aug 27 2019 - 05:36:12 EST
> -----Original Message-----
> From: Jonathan Hunter <jonathanh@xxxxxxxxxx>
> Sent: Tuesday, August 20, 2019 1:59 AM
> To: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>;
> gregkh@xxxxxxxxxxxxxxxxxxx; robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx;
> thierry.reding@xxxxxxxxx; Laxman Dewangan <ldewangan@xxxxxxxxxx>;
> jslaby@xxxxxxxx
> Cc: linux-serial@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-
> tegra@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Shardar Mohammed
> <smohammed@xxxxxxxxxx>
> Subject: Re: [PATCH 10/14] serial: tegra: add support to use 8 bytes trigger
>
>
> On 12/08/2019 12:28, Krishna Yarlagadda wrote:
> > From: Shardar Shariff Md <smohammed@xxxxxxxxxx>
> >
> > Add support to use 8 bytes trigger for Tegra186 SOC.
> >
> > Signed-off-by: Shardar Shariff Md <smohammed@xxxxxxxxxx>
> > Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
> > ---
> > drivers/tty/serial/serial-tegra.c | 13 +++++++++++--
> > 1 file changed, 11 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c
> > index 329923c..03d1d20 100644
> > --- a/drivers/tty/serial/serial-tegra.c
> > +++ b/drivers/tty/serial/serial-tegra.c
> > @@ -88,6 +88,7 @@ struct tegra_uart_chip_data {
> > bool support_clk_src_div;
> > bool fifo_mode_enable_status;
> > int uart_max_port;
> > + int dma_burst_bytes;
>
> I assume that this is a maximum, so why not say max_dma_burst_bytes?
Yes. This is maximum. Will update.
>
> > };
> >
> > struct tegra_uart_port {
> > @@ -933,7 +934,12 @@ static int tegra_uart_hw_init(struct
> tegra_uart_port *tup)
> > * programmed in the DMA registers.
> > */
> > tup->fcr_shadow = UART_FCR_ENABLE_FIFO;
> > - tup->fcr_shadow |= UART_FCR_R_TRIG_01;
> > +
> > + if (tup->cdata->dma_burst_bytes == 8)
> > + tup->fcr_shadow |= UART_FCR_R_TRIG_10;
> > + else
> > + tup->fcr_shadow |= UART_FCR_R_TRIG_01;
> > +
> > tup->fcr_shadow |= TEGRA_UART_TX_TRIG_16B;
> > tegra_uart_write(tup, tup->fcr_shadow, UART_FCR);
> >
> > @@ -1046,7 +1052,7 @@ static int
> tegra_uart_dma_channel_allocate(struct tegra_uart_port *tup,
> > }
> > dma_sconfig.src_addr = tup->uport.mapbase;
> > dma_sconfig.src_addr_width =
> DMA_SLAVE_BUSWIDTH_1_BYTE;
> > - dma_sconfig.src_maxburst = 4;
> > + dma_sconfig.src_maxburst = tup->cdata->dma_burst_bytes;
> > tup->rx_dma_chan = dma_chan;
> > tup->rx_dma_buf_virt = dma_buf;
> > tup->rx_dma_buf_phys = dma_phys;
> > @@ -1325,6 +1331,7 @@ static struct tegra_uart_chip_data
> tegra20_uart_chip_data = {
> > .support_clk_src_div = false,
> > .fifo_mode_enable_status = false,
> > .uart_max_port = 5,
> > + .dma_burst_bytes = 4,
>
> Isn't it simpler to store the TRIG value here?
>
> Jon
TRIG value will have to be converted to max burst and one of it needs to be
derived from other.
KY
>
> --
> nvpublic