Re: [PATCH] drm: bridge/dw_hdmi: add audio sample channel status setting

From: Cheng-yi Chiang
Date: Wed Sep 04 2019 - 06:52:57 EST

On Wed, Sep 4, 2019 at 6:32 PM Russell King - ARM Linux admin
<linux@xxxxxxxxxxxxxxx> wrote:
>
> On Wed, Sep 04, 2019 at 05:45:20PM +0800, Cheng-yi Chiang wrote:
> > On Wed, Sep 4, 2019 at 5:28 PM Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:
> > >
> > > Hi,
> > >
> > > On 04/09/2019 11:09, Cheng-yi Chiang wrote:
> > > > Hi,
> > > >
> > > > On Tue, Sep 3, 2019 at 5:53 PM Neil Armstrong <narmstrong@xxxxxxxxxxxx> wrote:
> > > >>
> > > >> Hi,
> > > >>
> > > >> On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
> > > >>> From: Yakir Yang <ykk@xxxxxxxxxxxxxx>
> > > >>>
> > > >>> When transmitting IEC60985 linear PCM audio, we configure the
> > > >>> Audio Sample Channel Status information of all the channel
> > > >>> status bits in the IEC60958 frame.
> > > >>> Refer to 60958-3 page 10 for frequency, original frequency, and
> > > >>> wordlength setting.
> > > >>>
> > > >>> This fix the issue that audio does not come out on some monitors
> > > >>> (e.g. LG 22CV241)
> > > >>>
> > > >>> Signed-off-by: Yakir Yang <ykk@xxxxxxxxxxxxxx>
> > > >>> Signed-off-by: Cheng-Yi Chiang <cychiang@xxxxxxxxxxxx>
> > > >>> ---
> > > >>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++
> > > >>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++
> > > >>> 2 files changed, 79 insertions(+)
> > > >>>
> > > >>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > >>> index bd65d0479683..34d46e25d610 100644
> > > >>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > >>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> > > >>> @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)
> > > >>> return n;
> > > >>> }
> > > >>>
> > > >>> +static void hdmi_set_schnl(struct dw_hdmi *hdmi)
> > > >>> +{
> > > >>> + u8 aud_schnl_samplerate;
> > > >>> + u8 aud_schnl_8;
> > > >>> +
> > > >>> + /* These registers are on RK3288 using version 2.0a. */
> > > >>> + if (hdmi->version != 0x200a)
> > > >>> + return;
> > > >>
> > > >> Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all
> > > >> SoCs ?
> > > >>
> > > >
> > > > In the original patch by Yakir,
> > > >
> > > > https://lore.kernel.org/patchwork/patch/539653/ (sorry, I should
> > > > have added this link in the "after the cut" note)
> > > >
> > > > The fix is limited to version 2.0.
> > > > Since I am only testing on RK3288 with 2.0a, I change the check to 2.0a only.
> > > > I can not test 2.0a version on other SoCs.
> > > > The databook I have at hand is 2.0a (not specific to RK3288) so I
> > > > think all 2.0a should have this register.
> > > >
> > > > As for other version like version 1.3 on iMX6, there is no such
> > > > register, as stated by Russell
> > > >
> > > > http://lkml.iu.edu/hypermail/linux/kernel/1501.3/06268.html.
> > >
> > > Russell assumes the registers are not present on the iMX6 IP not having
> > > the I2S registers, but they are present on the IPs configured with I2S
> > > at any versions.
> >
> > I see. Thanks for the check.
> >
> > >
> > > My databook version (1.40.a) specifies :
> > >
> > > fc_audschnls0 to fc_audschnls8
> > >
> > > ```
> > > When transmitting IEC60958 linear PCM audio, this registers allow to configure the channel status
> > > information of all the channel status bits in the IEC60958 frame. For the moment this configuration is only
> > > used when the I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA (AHBAUDDMA)
> > > interface is active (for S/PDIF interface this information comes from the stream).
> > > ```
> > >
> > > But the databook Revision History shows these registers were present since version 1.10a.
> > >
> > > I propose you remove the version check, but you only setup these registers when I2S is enabled:
> > > (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S) until a AHBAUDDMA user needs this,
> > > with a small comment explaining the situation.
> >
> > I see. Sound like a good plan.
> > In sum, I will add
> > set_channel_status()
> > in dw_hdmi.c
> > And in the beginning of this function,
> > check it is using I2S
> > (hdmi_readb(hdmi, HDMI_CONFIG0_ID) & HDMI_CONFIG0_I2S)
> > with a comment explaining the situation.
> >
> > And let dw-hdmi-audio-i2s dw_hdmi_i2s_hw_params() to call this
> > function after dw_hdmi_set_sample_rate, with word length (or
> > sample_bit) passed it as argument.
>
> If you're going to do it this way, there's little point having the
> check. The dw-hdmi-audio-i2s device will only be created if that
> ID bit is already set. So, provided set_channel_status() (which
> should probably be dw_hdmi_set_channel_status()) is only called from
> the I2S driver, then everything should be fine without such a check.
> However, it is worth noting in the docbook comments above the function
> that it is only for I2S setups.
>
I see. Yes it is simpler.
Thanks for the suggestion!
Will fix in v2.


> > I have not tested setting this register here as in the original patch
> > it was set in hdmi_set_clk_regenerator.
> > I will test it and update in my v2.
> >
> > Thanks again to everyone for the prompt reply and help.
> >
> > >
> > > Neil
> > >
> > > >
> > > > So at least we should check the version.
> > > > Maybe we can set the criteria as version 2.0 or above to make it a safe patch ?
> > > > If there is the same need on other SoC with version < 2.0, it can be
> > > > added later.
> > > > Presumably, there will be databook of that version to help confirming
> > > > this setting.
> > > >
> > > > Thanks!
> > > >>> +
> > > >>> + switch (hdmi->sample_rate) {
> > > >>> + case 32000:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;
> > > >>> + break;
> > > >>> + case 44100:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;
> > > >>> + break;
> > > >>> + case 48000:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;
> > > >>> + break;
> > > >>> + case 88200:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;
> > > >>> + break;
> > > >>> + case 96000:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;
> > > >>> + break;
> > > >>> + case 176400:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;
> > > >>> + break;
> > > >>> + case 192000:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;
> > > >>> + break;
> > > >>> + case 768000:
> > > >>> + aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;
> > > >>> + break;
> > > >>> + default:
> > > >>> + dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",
> > > >>> + hdmi->sample_rate);
> > > >>> + return;
> > > >>> + }
> > > >>> +
> > > >>> + /* set channel status register */
> > > >>> + hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
> > > >>> + HDMI_FC_AUDSCHNLS7);
> > > >>> +
> > > >>> + /*
> > > >>> + * Set original frequency to be the same as frequency.
> > > >>> + * Use one-complement value as stated in IEC60958-3 page 13.
> > > >>> + */
> > > >>> + aud_schnl_8 = (~aud_schnl_samplerate) <<
> > > >>> + HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;
> > > >>> +
> > > >>> + /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
> > > >>> + aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
> > > >>> +
> > > >>> + hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
> > > >>> +}
> > > >>> +
> > > >>> static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> > > >>> unsigned long pixel_clk, unsigned int sample_rate)
> > > >>> {
> > > >>> @@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
> > > >>> hdmi->audio_cts = cts;
> > > >>> hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0);
> > > >>> spin_unlock_irq(&hdmi->audio_lock);
> > > >>> +
> > > >>> + hdmi_set_schnl(hdmi);
> > > >>> }
> > > >>>
> > > >>> static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
> > > >>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > >>> index 6988f12d89d9..619ebc1c8354 100644
> > > >>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > >>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h
> > > >>> @@ -158,6 +158,17 @@
> > > >>> #define HDMI_FC_SPDDEVICEINF 0x1062
> > > >>> #define HDMI_FC_AUDSCONF 0x1063
> > > >>> #define HDMI_FC_AUDSSTAT 0x1064
> > > >>> +#define HDMI_FC_AUDSV 0x1065
> > > >>> +#define HDMI_FC_AUDSU 0x1066
> > > >>> +#define HDMI_FC_AUDSCHNLS0 0x1067
> > > >>> +#define HDMI_FC_AUDSCHNLS1 0x1068
> > > >>> +#define HDMI_FC_AUDSCHNLS2 0x1069
> > > >>> +#define HDMI_FC_AUDSCHNLS3 0x106a
> > > >>> +#define HDMI_FC_AUDSCHNLS4 0x106b
> > > >>> +#define HDMI_FC_AUDSCHNLS5 0x106c
> > > >>> +#define HDMI_FC_AUDSCHNLS6 0x106d
> > > >>> +#define HDMI_FC_AUDSCHNLS7 0x106e
> > > >>> +#define HDMI_FC_AUDSCHNLS8 0x106f
> > > >>> #define HDMI_FC_DATACH0FILL 0x1070
> > > >>> #define HDMI_FC_DATACH1FILL 0x1071
> > > >>> #define HDMI_FC_DATACH2FILL 0x1072
> > > >>> @@ -706,6 +717,15 @@ enum {
> > > >>> /* HDMI_FC_AUDSCHNLS7 field values */
> > > >>> HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4,
> > > >>> HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
> > > >>> + HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
> > > >>>
> > > >>> /* HDMI_FC_AUDSCHNLS8 field values */
> > > >>> HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,
> > > >>>
> > > >>
> > >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
> According to speedtest.net: 11.9Mbps down 500kbps up