Re: [PATCH 4/6] dt-bindings: phy: tegra: Add Tegra194 support

[Thierry Reding]

On Wed, Oct 02, 2019 at 04:00:49PM +0800, JC Kuo wrote:
> Extend the bindings to cover the set of features found in Tegra194.
> Note that, technically, there are four more supplies connected to the
> XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
> , but the power sequencing requirements of Tegra194 require these to be
> under the control of the PMIC.
> 
> Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it is
> possible for some platforms have long signal trace that could not
> provide sufficient electrical environment for Gen 2 speed. To deal with
> this, a new device node property "nvidia,disable-gen2" was added to
> Tegra194 that be used to specifically disable Gen 2 speed for a
> particular USB 3.0 port so that the port can be limited to Gen 1 speed
> and avoid the instability.
> 
> Signed-off-by: JC Kuo <jckuo@xxxxxxxxxx>
> ---
>  .../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 16 ++++++++++++++++
>  1 file changed, 16 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> index 9fb682e47c29..3bef37e7c365 100644
> --- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> @@ -37,6 +37,7 @@ Required properties:
>    - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
>    - Tegra210: "nvidia,tegra210-xusb-padctl"
>    - Tegra186: "nvidia,tegra186-xusb-padctl"
> +  - Tegra194: "nvidia,tegra194-xusb-padctl"
>  - reg: Physical base address and length of the controller's registers.
>  - resets: Must contain an entry for each entry in reset-names.
>  - reset-names: Must include the following entries:
> @@ -62,6 +63,10 @@ For Tegra186:
>  - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
>  - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
>  
> +For Tegra194:
> +- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
> +  3.3 V.
> +- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
>  
>  Pad nodes:
>  ==========
> @@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
>  - sata: sata-0
>    - functions: "usb3-ss", "sata"
>  
> +For Tegra194, the list of valid PHY nodes is given below:
> +- usb2: usb2-0, usb2-1, usb2-2, usb2-3
> +  - functions: "xusb"
> +- usb3: usb3-0, usb3-1, usb3-2, usb3-3
> +  - functions: "xusb"
>  
>  Port nodes:
>  ===========
> @@ -221,6 +231,9 @@ Optional properties:
>    is internal. In the absence of this property the port is considered to be
>    external.
>  
> +- nvidia,disable-gen2: A boolean property whose presence determines that a port
> +  should be limited to USB 3.1 Gen 1. This properlty is only for Tegra194.

s/properlty/property/

With that:

Acked-by: Thierry Reding <treding@xxxxxxxxxx>

Attachment: signature.asc
Description: PGP signature