[PATCH 1/2] arm64: dts: imx8mq-evk: Adjust nodes following alphabetical sort

[Anson Huang]

Adjust some nodes to make them follow alphabetical sort except
iomuxc node which is put at the end of file because of its huge
pinctrl data.

Signed-off-by: Anson Huang <Anson.Huang@xxxxxxx>
---
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 46 ++++++++++++++--------------
 1 file changed, 23 insertions(+), 23 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index 0595812..6ede46f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -115,15 +115,6 @@
 	};
 };
 
-&sai2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sai2>;
-	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>;
-	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>;
-	assigned-clock-rates = <0>, <24576000>;
-	status = "okay";
-};
-
 &gpio5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wifi_reset>;
@@ -242,6 +233,29 @@
 	power-supply = <&sw1a_reg>;
 };
 
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	n25q256a: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q256a", "jedec,spi-nor";
+		spi-max-frequency = <29000000>;
+	};
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1_BYPASS>, <&clk IMX8MQ_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <0>, <24576000>;
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -261,20 +275,6 @@
 	status = "okay";
 };
 
-&qspi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi>;
-	status = "okay";
-
-	n25q256a: flash@0 {
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "micron,n25q256a", "jedec,spi-nor";
-		spi-max-frequency = <29000000>;
-	};
-};
-
 &usdhc1 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc1>;
-- 
2.7.4