[PATCH 2/2] net: lpc_eth: parse phy nodes from device tree

[Alexandre Belloni]

When connected to a micrel phy, phy_find_first doesn't work properly
because the first phy found is on address 0, the broadcast address but, the
first thing the phy driver is doing is disabling this broadcast address.
The phy is then available only on address 1 but the mdio driver doesn't
know about it.

Instead, register the mdio bus using of_mdiobus_register and try to find
the phy description in device tree before falling back to phy_find_first.

This ultimately also allows to describe the interrupt the phy is connected
to.

Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
---
 drivers/net/ethernet/nxp/lpc_eth.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c
index 141571e2ec11..fdcaf70151d4 100644
--- a/drivers/net/ethernet/nxp/lpc_eth.c
+++ b/drivers/net/ethernet/nxp/lpc_eth.c
@@ -15,6 +15,7 @@
 #include <linux/etherdevice.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/phy.h>
 #include <linux/platform_device.h>
@@ -391,6 +392,7 @@ struct rx_status_t {
 struct netdata_local {
 	struct platform_device	*pdev;
 	struct net_device	*ndev;
+	struct device_node	*phy_node;
 	spinlock_t		lock;
 	void __iomem		*net_base;
 	u32			msg_enable;
@@ -749,22 +751,26 @@ static void lpc_handle_link_change(struct net_device *ndev)
 static int lpc_mii_probe(struct net_device *ndev)
 {
 	struct netdata_local *pldat = netdev_priv(ndev);
-	struct phy_device *phydev = phy_find_first(pldat->mii_bus);
-
-	if (!phydev) {
-		netdev_err(ndev, "no PHY found\n");
-		return -ENODEV;
-	}
+	struct phy_device *phydev;
 
 	/* Attach to the PHY */
 	if (lpc_phy_interface_mode(&pldat->pdev->dev) == PHY_INTERFACE_MODE_MII)
 		netdev_info(ndev, "using MII interface\n");
 	else
 		netdev_info(ndev, "using RMII interface\n");
+
+	if (pldat->phy_node)
+		phydev =  of_phy_find_device(pldat->phy_node);
+	else
+		phydev = phy_find_first(pldat->mii_bus);
+	if (!phydev) {
+		netdev_err(ndev, "no PHY found\n");
+		return -ENODEV;
+	}
+
 	phydev = phy_connect(ndev, phydev_name(phydev),
 			     &lpc_handle_link_change,
 			     lpc_phy_interface_mode(&pldat->pdev->dev));
-
 	if (IS_ERR(phydev)) {
 		netdev_err(ndev, "Could not attach to PHY\n");
 		return PTR_ERR(phydev);
@@ -812,7 +818,7 @@ static int lpc_mii_init(struct netdata_local *pldat)
 
 	platform_set_drvdata(pldat->pdev, pldat->mii_bus);
 
-	if (mdiobus_register(pldat->mii_bus))
+	if (of_mdiobus_register(pldat->mii_bus, pldat->pdev->dev.of_node))
 		goto err_out_unregister_bus;
 
 	if (lpc_mii_probe(pldat->ndev) != 0)
@@ -1345,6 +1351,8 @@ static int lpc_eth_drv_probe(struct platform_device *pdev)
 	netdev_dbg(ndev, "DMA buffer V address :0x%p\n",
 			pldat->dma_buff_base_v);
 
+	pldat->phy_node = of_parse_phandle(np, "phy-handle", 0);
+
 	/* Get MAC address from current HW setting (POR state is all zeros) */
 	__lpc_get_mac(pldat, ndev->dev_addr);
 
-- 
2.21.0