[PATCH v2] tty: serial: msm_serial: Fix flow control

[Jeffrey Hugo]

hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop.  As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990.  It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.

According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL.  Auto
hw flow control will manage RFR based on the configured watermark.  When
there is space to receive data, the hw will assert RFR.  When the watermark
is hit, the hw will de-assert RFR.

The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set.  SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.

msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR.  This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation.  It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured.  msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.

Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx>
---

v2:
-mask out RX_RDY_CTL in msm_reset() to close a small race window for RFR

 drivers/tty/serial/msm_serial.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 3657a24913fc..00964b6e4ac1 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -980,6 +980,7 @@ static unsigned int msm_get_mctrl(struct uart_port *port)
 static void msm_reset(struct uart_port *port)
 {
 	struct msm_port *msm_port = UART_TO_MSM(port);
+	unsigned int mr;
 
 	/* reset everything */
 	msm_write(port, UART_CR_CMD_RESET_RX, UART_CR);
@@ -987,7 +988,10 @@ static void msm_reset(struct uart_port *port)
 	msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR);
 	msm_write(port, UART_CR_CMD_RESET_BREAK_INT, UART_CR);
 	msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR);
-	msm_write(port, UART_CR_CMD_SET_RFR, UART_CR);
+	msm_write(port, UART_CR_CMD_RESET_RFR, UART_CR);
+	mr = msm_read(port, UART_MR1);
+	mr &= ~UART_MR1_RX_RDY_CTL;
+	msm_write(port, mr, UART_MR1);
 
 	/* Disable DM modes */
 	if (msm_port->is_uartdm)
-- 
2.17.1