Re: [PATCH V2 7/7] USB: serial: f81232: Add gpiolib to GPIO device

From: Johan Hovold
Date: Wed Oct 23 2019 - 08:21:56 EST

Next message: Matti Vaittinen: "[PATCH] gpio: bd70528: Add MODULE ALIAS to autoload module"
Previous message: Arnd Bergmann: "Re: [PATCH 04/36] usb: gadget: s3c-hsudc: remove platform header dependency"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Mon, Sep 23, 2019 at 10:24:49AM +0800, Ji-Ze Hong (Peter Hong) wrote:
> The Fintek F81534A series contains 3 GPIOs per UART and The max GPIOs
> is 12x3 = 36 GPIOs and this patch will implements GPIO device as a
> gpiochip to control all GPIO pins even transforms to transceiver pins.

Depending to your answer to my question whether these pins are truly
general purpose or not, this may not be the right interface.

> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@xxxxxxxxx>
> ---
> drivers/usb/serial/f81232.c | 249 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 249 insertions(+)
>
> diff --git a/drivers/usb/serial/f81232.c b/drivers/usb/serial/f81232.c
> index 82cc1e6cff62..dc9b28738b80 100644
> --- a/drivers/usb/serial/f81232.c
> +++ b/drivers/usb/serial/f81232.c
> @@ -18,6 +18,7 @@
> #include <linux/moduleparam.h>
> #include <linux/mutex.h>
> #include <linux/uaccess.h>
> +#include <linux/gpio.h>
> #include <linux/usb.h>
> #include <linux/usb/serial.h>
> #include <linux/serial_reg.h>
> @@ -104,6 +105,8 @@ MODULE_DEVICE_TABLE(usb, all_serial_id_table);
> #define F81534A_TRIGGER_MULTPILE_4X BIT(3)
> #define F81534A_FIFO_128BYTE (BIT(1) | BIT(0))
>
> +#define F81534A_MAX_PORT 12
> +
> /* Serial port self GPIO control, 2bytes [control&output data][input data] */
> #define F81534A_GPIO_REG 0x10e
> #define F81534A_GPIO_MODE2_DIR BIT(6) /* 1: input, 0: output */
> @@ -115,6 +118,13 @@ MODULE_DEVICE_TABLE(usb, all_serial_id_table);
>
> #define F81534A_CMD_ENABLE_PORT 0x116
>
> +/*
> + * Control device global GPIO control,
> + * 2bytes [control&output data][input data]
> + */
> +#define F81534A_CTRL_GPIO_REG 0x1601
> +#define F81534A_CTRL_GPIO_MAX_PIN 3
> +
> struct f81232_private {
> struct mutex lock;
> u8 modem_control;
> @@ -126,6 +136,12 @@ struct f81232_private {
> struct usb_serial_port *port;
> };
>
> +struct f81534a_ctrl_private {
> + struct usb_interface *intf;
> + struct gpio_chip chip;
> + struct mutex lock;
> +};
> +
> static u32 const baudrate_table[] = { 115200, 921600, 1152000, 1500000 };
> static u8 const clock_table[] = { F81232_CLK_1_846_MHZ, F81232_CLK_14_77_MHZ,
> F81232_CLK_18_46_MHZ, F81232_CLK_24_MHZ };
> @@ -863,6 +879,50 @@ static void f81232_lsr_worker(struct work_struct *work)
> dev_warn(&port->dev, "read LSR failed: %d\n", status);
> }
>
> +static int f81534a_ctrl_get_register(struct usb_device *dev, u16 reg, u16 size,
> + void *val)

Looks like this one needs to go under CONFIG_GPIOLIB as well.

> +{
> + int retry = F81534A_ACCESS_REG_RETRY;
> + int status;
> + u8 *tmp;
> +
> + tmp = kmalloc(size, GFP_KERNEL);
> + if (!tmp)
> + return -ENOMEM;
> +
> + while (retry--) {
> + status = usb_control_msg(dev,
> + usb_rcvctrlpipe(dev, 0),
> + F81534A_REGISTER_REQUEST,
> + F81534A_GET_REGISTER,
> + reg,
> + 0,
> + tmp,
> + size,
> + USB_CTRL_GET_TIMEOUT);
> + if (status != size) {
> + status = usb_translate_errors(status);
> + if (status == -EIO)
> + continue;
> +
> + status = -EIO;
> + } else {
> + status = 0;
> + memcpy(val, tmp, size);
> + }
> +
> + break;
> + }
> +
> + if (status) {
> + dev_err(&dev->dev, "get reg: %x, failed status: %d\n", reg,
> + status);
> + }
> +
> + kfree(tmp);
> + return status;
> +}
> +
> static int f81534a_ctrl_set_register(struct usb_device *dev, u16 reg, u16 size,
> void *val)
> {
> @@ -908,6 +968,182 @@ static int f81534a_ctrl_set_register(struct usb_device *dev, u16 reg, u16 size,
> return status;
> }
>
> +#ifdef CONFIG_GPIOLIB
> +static int f81534a_ctrl_set_mask_register(struct usb_device *dev, u16 reg,
> + u8 mask, u8 val)
> +{
> + int status;
> + u8 tmp;
> +
> + status = f81534a_ctrl_get_register(dev, reg, 1, &tmp);
> + if (status)
> + return status;
> +
> +
> + tmp = (tmp & ~mask) | (val & mask);
> +
> + status = f81534a_ctrl_set_register(dev, reg, 1, &tmp);
> + if (status)
> + return status;
> +
> + return 0;
> +}
> +
> +static int f81534a_gpio_get(struct gpio_chip *chip, unsigned int gpio_num)
> +{
> + struct f81534a_ctrl_private *priv = gpiochip_get_data(chip);
> + struct usb_interface *intf = priv->intf;
> + struct usb_device *dev = interface_to_usbdev(intf);
> + int status;
> + u8 tmp[2];
> + int set;
> + int idx;
> + int reg;
> +
> + set = gpio_num / F81534A_CTRL_GPIO_MAX_PIN;
> + idx = gpio_num % F81534A_CTRL_GPIO_MAX_PIN;
> + reg = F81534A_CTRL_GPIO_REG + set;
> +
> + mutex_lock(&priv->lock);
> +
> + status = f81534a_ctrl_get_register(dev, reg, sizeof(tmp), tmp);
> + if (status) {
> + mutex_unlock(&priv->lock);
> + return status;
> + }
> +
> + mutex_unlock(&priv->lock);
> +
> + return !!(tmp[1] & BIT(idx));
> +}
> +
> +static int f81534a_gpio_direction_in(struct gpio_chip *chip,
> + unsigned int gpio_num)
> +{
> + struct f81534a_ctrl_private *priv = gpiochip_get_data(chip);
> + struct usb_interface *intf = priv->intf;
> + struct usb_device *dev = interface_to_usbdev(intf);
> + int status;
> + int set;
> + int idx;
> + int reg;
> + u8 mask;
> +
> + set = gpio_num / F81534A_CTRL_GPIO_MAX_PIN;
> + idx = gpio_num % F81534A_CTRL_GPIO_MAX_PIN;
> + mask = F81534A_GPIO_MODE0_DIR << idx;
> + reg = F81534A_CTRL_GPIO_REG + set;
> +
> + mutex_lock(&priv->lock);
> + status = f81534a_ctrl_set_mask_register(dev, reg, mask, mask);
> + mutex_unlock(&priv->lock);
> +
> + return status;
> +}
> +
> +static int f81534a_gpio_direction_out(struct gpio_chip *chip,
> + unsigned int gpio_num, int val)
> +{
> + struct f81534a_ctrl_private *priv = gpiochip_get_data(chip);
> + struct usb_interface *intf = priv->intf;
> + struct usb_device *dev = interface_to_usbdev(intf);
> + int status;
> + int set;
> + int idx;
> + int reg;
> + u8 mask;
> + u8 data;
> +
> + set = gpio_num / F81534A_CTRL_GPIO_MAX_PIN;
> + idx = gpio_num % F81534A_CTRL_GPIO_MAX_PIN;
> + mask = (F81534A_GPIO_MODE0_DIR << idx) | BIT(idx);
> + reg = F81534A_CTRL_GPIO_REG + set;
> + data = val ? BIT(idx) : 0;
> +
> + mutex_lock(&priv->lock);
> + status = f81534a_ctrl_set_mask_register(dev, reg, mask, data);
> + mutex_unlock(&priv->lock);
> +
> + return status;
> +}
> +
> +static void f81534a_gpio_set(struct gpio_chip *chip, unsigned int gpio_num,
> + int val)
> +{
> + f81534a_gpio_direction_out(chip, gpio_num, val);
> +}
> +
> +static int f81534a_gpio_get_direction(struct gpio_chip *chip,
> + unsigned int gpio_num)
> +{
> + struct f81534a_ctrl_private *priv = gpiochip_get_data(chip);
> + struct usb_interface *intf = priv->intf;
> + struct usb_device *dev = interface_to_usbdev(intf);
> + int status;
> + u8 tmp[2];
> + int set;
> + int idx;
> + int reg;
> + u8 mask;
> +
> + set = gpio_num / F81534A_CTRL_GPIO_MAX_PIN;
> + idx = gpio_num % F81534A_CTRL_GPIO_MAX_PIN;
> + mask = F81534A_GPIO_MODE0_DIR << idx;
> + reg = F81534A_CTRL_GPIO_REG + set;
> +
> + mutex_lock(&priv->lock);
> +
> + status = f81534a_ctrl_get_register(dev, reg, sizeof(tmp), tmp);
> + if (status) {
> + mutex_unlock(&priv->lock);
> + return status;
> + }
> +
> + mutex_unlock(&priv->lock);
> +
> + if (tmp[0] & mask)
> + return GPIOF_DIR_IN;
> +
> + return GPIOF_DIR_OUT;
> +}
> +
> +static int f81534a_prepare_gpio(struct usb_interface *intf)

Could you rename this f81534a_gpiochip_register or similar?

> +{
> + struct f81534a_ctrl_private *priv = usb_get_intfdata(intf);
> + int status;
> +
> + priv->chip.parent = &intf->dev;
> + priv->chip.owner = THIS_MODULE;
> + priv->chip.get_direction = f81534a_gpio_get_direction,
> + priv->chip.get = f81534a_gpio_get;
> + priv->chip.direction_input = f81534a_gpio_direction_in;
> + priv->chip.set = f81534a_gpio_set;
> + priv->chip.direction_output = f81534a_gpio_direction_out;
> + priv->chip.label = "f81534a";
> + priv->chip.can_sleep = true;
> + /* M0(SD)/M1/M2 */
> + priv->chip.ngpio = F81534A_CTRL_GPIO_MAX_PIN * F81534A_MAX_PORT;
> + priv->chip.base = -1;
> +
> + priv->intf = intf;

Maybe store the parent struct usb_device instead since that's what you
end up using?

> + mutex_init(&priv->lock);

Already initialised in probe() below. Same with priv->intf by the way.

> +
> + status = devm_gpiochip_add_data(&intf->dev, &priv->chip, priv);
> + if (status) {
> + dev_err(&intf->dev, "failed to register gpiochip: %d\n",
> + status);
> + return status;
> + }

Have you tried disconnecting the device with gpios requested? This used
to break gpiolib, but was fixed. Just want to make sure it hasn't
regressed.

> +
> + return 0;
> +}
> +#else
> +static int f81534a_prepare_gpio(struct usb_interface *intf)
> +{
> + return 0;
> +}
> +#endif
> +
> static int f81534a_ctrl_enable_all_ports(struct usb_interface *intf)
> {
> struct usb_device *dev = interface_to_usbdev(intf);
> @@ -930,8 +1166,21 @@ static int f81534a_ctrl_probe(struct usb_interface *intf,
> const struct usb_device_id *id)
> {
> struct usb_device *dev = interface_to_usbdev(intf);
> + struct f81534a_ctrl_private *priv;
> int status;
>
> + priv = devm_kzalloc(&intf->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + mutex_init(&priv->lock);
> + usb_set_intfdata(intf, priv);
> + priv->intf = intf;
> +
> + status = f81534a_prepare_gpio(intf);
> + if (status)
> + return status;
> +
> status = f81534a_ctrl_enable_all_ports(intf);
> if (status)
> return status;

Overall this all look much better now.

Thanks,
Johan

Next message: Matti Vaittinen: "[PATCH] gpio: bd70528: Add MODULE ALIAS to autoload module"
Previous message: Arnd Bergmann: "Re: [PATCH 04/36] usb: gadget: s3c-hsudc: remove platform header dependency"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]