Re: [RFC PATCH v2 02/13] dt-bindings: mfd: Document ROHM BD71828 bindings

[Dan Murphy]

Matti

On 10/24/19 6:41 AM, Matti Vaittinen wrote:
> ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
> a real-time clock (RTC), 3 GPO/regulator control pins, HALL input
> and a 32.768 kHz clock gate.
>
> Document the dt bindings drivers are using.
>
> Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
> ---
>
> No changes since v1
>
>   .../bindings/mfd/rohm,bd71828-pmic.txt        | 180 ++++++++++++++++++
>   1 file changed, 180 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt

I will let maintainers weigh in here but if this is new this should 
probably be in the yaml format to avoid conversion in the future


> diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
> new file mode 100644
> index 000000000000..125efa9f3de0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
> @@ -0,0 +1,180 @@
> +* ROHM BD71828 Power Management Integrated Circuit bindings
> +
> +BD71828GW is a single-chip power management IC for battery-powered portable
> +devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA single-cell
> +linear charger. Also included is a Coulomb counter, a real-time clock (RTC),
> +and a 32.768 kHz clock gate.
> +
> +Required properties:
> + - compatible			: Should be "rohm,bd71828".
> + - reg				: I2C slave address.
> + - interrupt-parent		: Phandle to the parent interrupt controller.
> + - interrupts			: The interrupt line the device is connected to.
> + - clocks			: The parent clock connected to PMIC.
> + - #clock-cells			: Should be 0.
> + - regulators			: List of child nodes that specify the
> +				  regulators. Please see
> +				  ../regulator/rohm,bd71828-regulator.txt
> + - gpio-controller		: To indicate BD71828 acts as a GPIO controller.
> + - #gpio-cells			: Should be 2. The first cell is the pin number
> +				  and the second cell is used to specify flags.
> +				  See ../gpio/gpio.txt for more information.
> +
> +The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
> +RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
> +via I2C, or some/all of them can be bound to run-levels and controlled as a
> +group. If bucks are controlled individually these run-levels are ignored. See
> +../regulator/rohm,bd71828-regulator.txt for how to define regulator voltages
The rohm,bd71828-regulator.txt should be yaml if the maintainers want it 
that way.
> +for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's OTP
> +configuration.
> +
> +Optional properties:
> +- clock-output-names		: Should contain name for output clock.
> +- rohm,dvs-vsel-gpios		: GPIOs used to control PMIC run-levels. Should
> +				  describe two GPIOs. (See run-level control in
> +				  data-sheet). If this property is omitted but
> +				  some bucks are marked to be controlled by
> +				  run-levels - then OTP option allowing
> +				  run-level control via I2C is assumed.
> +- gpio-reserved-ranges		: Usage of GPIO pins can be changed via OTP.
> +				  This property can be used to mark the pins
> +				  which should not be configured for GPIO.
> +				  Please see the ../gpio/gpio.txt for more
> +				  information.
> +
> +Example:
> +

This example does not look right.

I see that I2C is referenced above so the example could look like this

osc: oscillator {
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ compatible = "fixed-clock";
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ #clock-cells = <1>;
 clock-frequency = <32768>;
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ clock-output-names = "osc";
ÂÂÂÂÂÂÂ };

This is an external oscillator and is not really part of the pmic 
itself. I am not sure you even need to define that since it is not part 
of the pmic.

i2c {

ÂÂÂ ÂÂÂ pmic@4b {

ÂÂÂ ÂÂÂ ÂÂÂ ÂÂÂ [...]

ÂÂÂ ÂÂÂ };

};

Dan