[PATCH v2 3/4] arm64: dts: freescale: Add devicetree support for Thor96 board

From: Manivannan Sadhasivam
Date: Wed Oct 30 2019 - 05:02:18 EST

Next message: Greg Kroah-Hartman: "Re: [PATCH 4.14 027/119] MIPS: elf_hwcap: Export userspace ASEs"
Previous message: Manivannan Sadhasivam: "[PATCH v2 2/4] dt-bindings: arm: Add devicetree binding for Thor96 Board"
In reply to: Manivannan Sadhasivam: "[PATCH v2 2/4] dt-bindings: arm: Add devicetree binding for Thor96 Board"
Next in thread: Manivannan Sadhasivam: "[PATCH v2 4/4] mtd: spi-nor: Add support for w25q256jw"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Add devicetree support for Thor96 board from Einfochips. This board is
one of the 96Boards Consumer Edition platform powered by the NXP
i.MX8MQ SoC.

Following are the features supported currently:

1. uSD
2. WiFi/BT
3. Ethernet
4. EEPROM (M24256)
5. NOR Flash (W25Q256JW)
6. 2xUSB3.0 ports and 1xUSB2.0 port at HS expansion

More information about this board can be found in Arrow website:
https://www.arrow.com/en/products/i.imx8-thor96/arrow-development-tools

Link to 96Boards CE Specification: https://linaro.co/ce-specification

Signed-off-by: Darshak Patel <darshak.patel@xxxxxxxxxxxxxx>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/imx8mq-thor96.dts | 581 ++++++++++++++++++
2 files changed, 582 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-thor96.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 93fce8f0c66d..dec1662019be 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
new file mode 100644
index 000000000000..b4795a032fa2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 Einfochips
+ * Copyright 2019 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "imx8mq.dtsi"
+
+/ {
+ model = "Einfochips i.MX8MQ Thor96";
+ compatible = "einfochips,imx8mq-thor96", "fsl,imx8mq";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000 0 0x80000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ user-led1 {
+ label = "green:user1";
+ gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ user-led2 {
+ label = "green:user2";
+ gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ };
+
+ user-led3 {
+ label = "green:user3";
+ gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+
+ user-led4 {
+ label = "green:user4";
+ gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ linux,default-trigger = "none";
+ };
+
+ wlan-active-led {
+ label = "yellow:wlan";
+ gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ bt-active-led {
+ label = "blue:bt";
+ gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "hci0-power";
+ default-state = "off";
+ };
+ };
+
+ reg_usdhc1_vmmc: reg-usdhc1-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usdhc1_vqmmc: reg-usdhc1-vqmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8_EXT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_usdhc2_vmmc: reg-usdhc2-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vqmmc: reg-usdhc2-vqmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "NVCC_SD2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_reg_on>;
+ gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* LS-SPI0 */
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ phy-handle = <&ethphy>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+ };
+};
+
+/* LS-I2C0 */
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@8 {
+ compatible = "fsl,pfuze100";
+ reg = <0x8>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3ab {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
+
+/* LS-I2C1 */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+};
+
+/* HS-I2C2 */
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+/* HS-I2C3 */
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&sw1c_reg>;
+};
+
+&qspi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi0>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <100000000>;
+ reg = <0>;
+ };
+};
+
+/* Debug UART */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+ status = "okay";
+};
+
+/* LS-UART0 */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ device-wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_bt_gpios>;
+ };
+};
+
+/* LS-UART1 */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* SDIO */
+&usdhc1 {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ vmmc-supply = <&reg_usdhc1_vmmc>;
+ vqmmc-supply = <&reg_usdhc1_vqmmc>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ no-sd;
+ no-emmc;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* uSD */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ vmmc-supply = <&reg_usdhc2_vmmc>;
+ vqmmc-supply = <&reg_usdhc2_vqmmc>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ no-sdio;
+ no-emmc;
+ disable-wp;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_bt_gpios: btgpiosgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19
+ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19
+ MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x16
+ MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x16
+ MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x16
+ MX8MQ_IOMUXC_ECSPI2_SS0_ECSPI2_SS0 0x16
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x4
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x24
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1c
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1c
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1c
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1c
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1c
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1c
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x19
+ MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
+ MX8MQ_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19
+ MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19
+ MX8MQ_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19
+ MX8MQ_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19
+ >;
+ };
+
+ pinctrl_qspi0: qspi0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
+ MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+
+ >;
+ };
+
+ pinctrl_reg_usdhc2: regusdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
+ MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8c
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcc
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcc
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcc
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcc
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcc
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9c
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdc
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdc
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdc
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdc
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdc
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xcc
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+
+ pinctrl_wifi_reg_on: wifiregongrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x17059
+ >;
+ };
+};
--
2.17.1

Next message: Greg Kroah-Hartman: "Re: [PATCH 4.14 027/119] MIPS: elf_hwcap: Export userspace ASEs"
Previous message: Manivannan Sadhasivam: "[PATCH v2 2/4] dt-bindings: arm: Add devicetree binding for Thor96 Board"
In reply to: Manivannan Sadhasivam: "[PATCH v2 2/4] dt-bindings: arm: Add devicetree binding for Thor96 Board"
Next in thread: Manivannan Sadhasivam: "[PATCH v2 4/4] mtd: spi-nor: Add support for w25q256jw"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]