[PATCH 3/3] arm64: dts: qcom: db845c: Enable PCIe controllers

[Bjorn Andersson]

Enable the two PCIe controllers found on the Dragonboard845c.

Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 91 ++++++++++++++++++++++
 1 file changed, 91 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index f5a85caff1a3..c314b5d55796 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -340,6 +340,39 @@
 			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
 };
 
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+
+	vddpe-3v3-supply = <&pcie0_3p3v_dual>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+};
+
+&pcie0_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+};
+
+&pcie1_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
 &pm8998_gpio {
 	vol_up_pin_a: vol-up-active {
 		pins = "gpio6";
@@ -382,6 +415,31 @@
 };
 
 &tlmm {
+	pcie0_default_state: pcie0-default {
+		clkreq {
+			pins = "gpio36";
+			function = "pci_e0";
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio35";
+			function = "gpio";
+
+			drive-strength = <2>;
+			output-low;
+			bias-pull-down;
+		};
+
+		wake-n {
+			pins = "gpio37";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie0_pwren_state: pcie0-pwren {
 		pins = "gpio90";
 		function = "gpio";
@@ -390,6 +448,39 @@
 		bias-disable;
 	};
 
+	pcie1_default_state: pcie1-default {
+		perst-n {
+			pins = "gpio102";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		clkreq {
+			pins = "gpio103";
+			function = "pci_e1";
+			bias-pull-up;
+		};
+
+		wake-n {
+			pins = "gpio11";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio75";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+
 	sdc2_default_state: sdc2-default {
 		clk {
 			pins = "sdc2_clk";
-- 
2.23.0