Quoting Rajendra Nayak (2019-11-05 22:50:05)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
new file mode 100644
index 000000000000..17870dd67390
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -0,0 +1,299 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SC7180 SoC device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sc7180.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32764>;
+ clock-output-names = "sleep_clk";
Remove this one too?
+ #clock-cells = <0>;[...]
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0 0x80000000 0 0>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ soc: soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0 0 0 0 0x10 0>;
+ dma-ranges = <0 0 0 0 0x10 0>;
+ compatible = "simple-bus";
+
+ gcc: clock-controller@100000 {
+ compatible = "qcom,gcc-sc7180";
+ reg = <0 0x00100000 0 0x1f0000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x6000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ uart8: serial@a88000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_default>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ tlmm: pinctrl@3500000 {
+ compatible = "qcom,sc7180-pinctrl";
+ reg = <0 0x03500000 0 0x300000>,
+ <0 0x03900000 0 0x300000>,
+ <0 0x03d00000 0 0x300000>;
+ reg-names = "west", "north", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 120>;
+
+ qup_uart8_default: qup-uart8-default {
+ pinmux {
+ pins = "gpio44", "gpio45";
+ function = "qup12";
That looks weird to have qup12 function on uart8. It's right?