[PATCH 4.9 25/34] net: bcmgenet: reset 40nm EPHY on energy detect

[Greg Kroah-Hartman]

From: Doug Berger <opendmb@xxxxxxxxx>

[ Upstream commit 25382b991d252aed961cd434176240f9de6bb15f ]

The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.

It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@xxxxxxxxx>
Acked-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c |    9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -1914,6 +1914,8 @@ static void bcmgenet_link_intr_enable(st
 	 */
 	if (priv->internal_phy) {
 		int0_enable |= UMAC_IRQ_LINK_EVENT;
+		if (GENET_IS_V1(priv) || GENET_IS_V2(priv) || GENET_IS_V3(priv))
+			int0_enable |= UMAC_IRQ_PHY_DET_R;
 	} else if (priv->ext_phy) {
 		int0_enable |= UMAC_IRQ_LINK_EVENT;
 	} else if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) {
@@ -2531,6 +2533,10 @@ static void bcmgenet_irq_task(struct wor
 		bcmgenet_power_up(priv, GENET_POWER_WOL_MAGIC);
 	}
 
+	if (status & UMAC_IRQ_PHY_DET_R &&
+	    priv->dev->phydev->autoneg != AUTONEG_ENABLE)
+		phy_init_hw(priv->dev->phydev);
+
 	/* Link UP/DOWN event */
 	if (status & UMAC_IRQ_LINK_EVENT)
 		phy_mac_interrupt(priv->phydev,
@@ -2627,8 +2633,7 @@ static irqreturn_t bcmgenet_isr0(int irq
 	}
 
 	/* all other interested interrupts handled in bottom half */
-	status &= (UMAC_IRQ_LINK_EVENT |
-		   UMAC_IRQ_MPD_R);
+	status &= (UMAC_IRQ_LINK_EVENT | UMAC_IRQ_MPD_R | UMAC_IRQ_PHY_DET_R);
 	if (status) {
 		/* Save irq status for bottom-half processing. */
 		spin_lock_irqsave(&priv->lock, flags);