Re: [PATCH v2 1/2] remoteproc: qcom_q6v5_mss: Don't reassign mpss region on shutdown

[Jeffrey Hugo]

On Tue, Nov 12, 2019 at 10:01 AM Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx> wrote:
>
> On Fri, Nov 8, 2019 at 5:40 PM Bjorn Andersson
> <bjorn.andersson@xxxxxxxxxx> wrote:
> >
> > Trying to reclaim mpss memory while the mba is not running causes the
> > system to crash on devices with security fuses blown, so leave it
> > assigned to the remote on shutdown and recover it on a subsequent boot.
> >
> > Fixes: 6c5a9dc2481b ("remoteproc: qcom: Make secure world call for mem ownership switch")
> > Cc: stable@xxxxxxxxxxxxxxx
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>
> Stuff still works on the laptop, and I don't hit the access violation
> with the crash dump scenario on the mtp.
>
> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx>
> Tested-by: Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx>

Actually, nack that.  See comment below.

>
> > ---
> >
> > Changes since v1:
> > - Assign memory back to Linux in coredump case
> >
> >  drivers/remoteproc/qcom_q6v5_mss.c | 20 ++++++++++----------
> >  1 file changed, 10 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/remoteproc/qcom_q6v5_mss.c b/drivers/remoteproc/qcom_q6v5_mss.c
> > index de919f2e8b94..efab574b2e12 100644
> > --- a/drivers/remoteproc/qcom_q6v5_mss.c
> > +++ b/drivers/remoteproc/qcom_q6v5_mss.c
> > @@ -875,11 +875,6 @@ static void q6v5_mba_reclaim(struct q6v5 *qproc)
> >                 writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
> >         }
> >
> > -       ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm,
> > -                                     false, qproc->mpss_phys,
> > -                                     qproc->mpss_size);
> > -       WARN_ON(ret);
> > -
> >         q6v5_reset_assert(qproc);
> >
> >         q6v5_clk_disable(qproc->dev, qproc->reset_clks,
> > @@ -969,6 +964,10 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
> >                         max_addr = ALIGN(phdr->p_paddr + phdr->p_memsz, SZ_4K);
> >         }
> >
> > +       /* Try to reset ownership back to Linux */
> > +       q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false,
> > +                               qproc->mpss_phys, qproc->mpss_size);
> > +
> >         mpss_reloc = relocate ? min_addr : qproc->mpss_phys;
> >         qproc->mpss_reloc = mpss_reloc;
> >         /* Load firmware segments */
> > @@ -1058,9 +1057,14 @@ static void qcom_q6v5_dump_segment(struct rproc *rproc,
> >         void *ptr = rproc_da_to_va(rproc, segment->da, segment->size);
> >
> >         /* Unlock mba before copying segments */
> > -       if (!qproc->dump_mba_loaded)
> > +       if (!qproc->dump_mba_loaded) {
> >                 ret = q6v5_mba_load(qproc);
> >
> > +               /* Try to reset ownership back to Linux */
> > +               q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false,
> > +                                       qproc->mpss_phys, qproc->mpss_size);

If the load fails, we can't pull the memory otherwise we'll hit the
access violation (serror).  I happened to see this on a production
device, where I think the load fails because crashdumps are not
enabled.

> > +       }
> > +
> >         if (!ptr || ret)
> >                 memset(dest, 0xff, segment->size);
> >         else
> > @@ -1111,10 +1115,6 @@ static int q6v5_start(struct rproc *rproc)
> >         return 0;
> >
> >  reclaim_mpss:
> > -       xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm,
> > -                                               false, qproc->mpss_phys,
> > -                                               qproc->mpss_size);
> > -       WARN_ON(xfermemop_ret);
> >         q6v5_mba_reclaim(qproc);
> >
> >         return ret;
> > --
> > 2.23.0
> >