Re: [PATCH] staging: rtl8192u: fix indentation issue

[walter harms]

Am 14.11.2019 10:54, schrieb Colin King:
> From: Colin Ian King <colin.king@xxxxxxxxxxxxx>
> 
> There is a block of statements that are indented
> too deeply, remove the extraneous tabs.
> 
> Signed-off-by: Colin Ian King <colin.king@xxxxxxxxxxxxx>
> ---
>  drivers/staging/rtl8192u/r819xU_cmdpkt.c | 25 ++++++++++++------------
>  1 file changed, 13 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/staging/rtl8192u/r819xU_cmdpkt.c b/drivers/staging/rtl8192u/r819xU_cmdpkt.c
> index e064f43fd8b6..bc98cdaf61ec 100644
> --- a/drivers/staging/rtl8192u/r819xU_cmdpkt.c
> +++ b/drivers/staging/rtl8192u/r819xU_cmdpkt.c
> @@ -169,19 +169,20 @@ static void cmdpkt_beacontimerinterrupt_819xusb(struct net_device *dev)
>  {
>  	struct r8192_priv *priv = ieee80211_priv(dev);
>  	u16 tx_rate;
> -		/* 87B have to S/W beacon for DTM encryption_cmn. */
> -		if (priv->ieee80211->current_network.mode == IEEE_A ||
> -		    priv->ieee80211->current_network.mode == IEEE_N_5G ||
> -		    (priv->ieee80211->current_network.mode == IEEE_N_24G &&
> -		     (!priv->ieee80211->pHTInfo->bCurSuppCCK))) {
> -			tx_rate = 60;
> -			DMESG("send beacon frame  tx rate is 6Mbpm\n");
> -		} else {
> -			tx_rate = 10;
> -			DMESG("send beacon frame  tx rate is 1Mbpm\n");
> -		}
>  
> -		rtl819xusb_beacon_tx(dev, tx_rate); /* HW Beacon */
> +	/* 87B have to S/W beacon for DTM encryption_cmn. */
> +	if (priv->ieee80211->current_network.mode == IEEE_A ||
> +	    priv->ieee80211->current_network.mode == IEEE_N_5G ||
> +	    (priv->ieee80211->current_network.mode == IEEE_N_24G &&
> +	     (!priv->ieee80211->pHTInfo->bCurSuppCCK))) {
> +		tx_rate = 60;
> +		DMESG("send beacon frame  tx rate is 6Mbpm\n");
> +	} else {
> +		tx_rate = 10;
> +		DMESG("send beacon frame  tx rate is 1Mbpm\n");
> +	}
> +
> +	rtl819xusb_beacon_tx(dev, tx_rate); /* HW Beacon */
>  }
>  
>  /*-----------------------------------------------------------------------------

this is hard to read in the first place.
Maybe using switch() here is better to read (untested example below).


	switch(priv->ieee80211->current_network.mode) {

	case IEEE_A:
	case IEEE_N_5G:
	 tx_rate = 60;
         break;
        IEEE_N_24G:
	     if ( !priv->ieee80211->pHTInfo->bCurSuppCCK )
		tx_rate = 60;
             // fall truh

        default:
		tx_rate = 10;

	}	

	if (txrate == 60 )
	     DMESG("send beacon frame  tx rate is 6Mbpm\n");
	else if (txrate == 10 )
	     DMESG("send beacon frame  tx rate is 1Mbpm\n");

JM2C

re,
 wh