Re: [PATCH v5 1/4] Bluetooth: hci_bcm: Disallow set_baudrate for BCM4354

[Marcel Holtmann]

Hi Abhishek,

> Without updating the patchram, the BCM4354 does not support a higher
> operating speed. The normal bcm_setup follows the correct order
> (init_speed, patchram and then oper_speed) but the serdev driver will
> set the operating speed before calling the hu->setup function. Thus,
> for the BCM4354, don't set the operating speed before patchram.
> 
> Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@xxxxxxxxxxxx>
> ---
> 
> Changes in v5: None
> Changes in v4: None
> Changes in v3: None
> Changes in v2: None
> 
> drivers/bluetooth/hci_bcm.c | 31 +++++++++++++++++++++++++++++--
> 1 file changed, 29 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
> index 0f851c0dde7f..ee40003008d8 100644
> --- a/drivers/bluetooth/hci_bcm.c
> +++ b/drivers/bluetooth/hci_bcm.c
> @@ -47,6 +47,14 @@
> 
> #define BCM_NUM_SUPPLIES 2
> 
> +/**
> + * struct bcm_device_data - device specific data
> + * @no_early_set_baudrate: Disallow set baudrate before driver setup()
> + */
> +struct bcm_device_data {
> +	bool	no_early_set_baudrate;
> +};
> +
> /**
>  * struct bcm_device - device driver resources
>  * @serdev_hu: HCI UART controller struct
> @@ -79,6 +87,7 @@
>  * @hu: pointer to HCI UART controller struct,
>  *	used to disable flow control during runtime suspend and system sleep
>  * @is_suspended: whether flow control is currently disabled
> + * @no_early_set_baudrate: don't set_baudrate before setup()
>  */
> struct bcm_device {
> 	/* Must be the first member, hci_serdev.c expects this. */
> @@ -112,6 +121,7 @@ struct bcm_device {
> 	struct hci_uart		*hu;
> 	bool			is_suspended;
> #endif
> +	bool			no_early_set_baudrate;
> };
> 
> /* generic bcm uart resources */
> @@ -447,7 +457,13 @@ static int bcm_open(struct hci_uart *hu)
> 	if (bcm->dev) {
> 		hci_uart_set_flow_control(hu, true);
> 		hu->init_speed = bcm->dev->init_speed;
> -		hu->oper_speed = bcm->dev->oper_speed;
> +
> +		/* If oper_speed is set, ldisc/serdev will set the baudrate
> +		 * before calling setup()
> +		 */
> +		if (!bcm->dev->no_early_set_baudrate)
> +			hu->oper_speed = bcm->dev->oper_speed;
> +
> 		err = bcm_gpio_set_power(bcm->dev, true);
> 		hci_uart_set_flow_control(hu, false);
> 		if (err)
> @@ -565,6 +581,8 @@ static int bcm_setup(struct hci_uart *hu)
> 	/* Operational speed if any */
> 	if (hu->oper_speed)
> 		speed = hu->oper_speed;
> +	else if (bcm->dev && bcm->dev->oper_speed)
> +		speed = bcm->dev->oper_speed;
> 	else if (hu->proto->oper_speed)
> 		speed = hu->proto->oper_speed;
> 	else
> @@ -1374,6 +1392,7 @@ static struct platform_driver bcm_driver = {
> static int bcm_serdev_probe(struct serdev_device *serdev)
> {
> 	struct bcm_device *bcmdev;
> +	const struct bcm_device_data *data;
> 	int err;
> 
> 	bcmdev = devm_kzalloc(&serdev->dev, sizeof(*bcmdev), GFP_KERNEL);
> @@ -1408,6 +1427,10 @@ static int bcm_serdev_probe(struct serdev_device *serdev)
> 	if (err)
> 		dev_err(&serdev->dev, "Failed to power down\n");
> 
> +	data = device_get_match_data(bcmdev->dev);
> +	if (data)
> +		bcmdev->no_early_set_baudrate = data->no_early_set_baudrate;
> +
> 	return hci_uart_register_device(&bcmdev->serdev_hu, &bcm_proto);
> }
> 
> @@ -1419,12 +1442,16 @@ static void bcm_serdev_remove(struct serdev_device *serdev)
> }
> 
> #ifdef CONFIG_OF
> +struct bcm_device_data bcm4354_device_data = {
> +	.no_early_set_baudrate = true,
> +};
> +
> static const struct of_device_id bcm_bluetooth_of_match[] = {
> 	{ .compatible = "brcm,bcm20702a1" },
> 	{ .compatible = "brcm,bcm4345c5" },
> 	{ .compatible = "brcm,bcm4330-bt" },
> 	{ .compatible = "brcm,bcm43438-bt" },
> -	{ .compatible = "brcm,bcm43540-bt" },
> +	{ .compatible = "brcm,bcm43540-bt", .data = &bcm4354_device_data },

this looks good to me. Can some users of the other devices test this patch so we ensure that it wonât break other devices.

Regards

Marcel