Re: [PATCH v2 17/17] ARM: dts: tegra30: cardhu-a04: Add CPU Operating Performance Points

From: Jon Hunter
Date: Mon Nov 18 2019 - 04:52:11 EST

Next message: Jerome Brunet: "Re: [PATCH v3 0/2] add the DDR clock controller on Meson8 and Meson8b"
Previous message: Bean Huo (beanhuo): "RE: [EXT] [PATCH v2 4/4] scsi: ufs: Complete pending requests in host reset and restore path"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 15/11/2019 20:35, Dmitry Osipenko wrote:
> 15.11.2019 20:31, Jon Hunter ÐÐÑÐÑ:
>>
>>
>> On 15/11/2019 14:55, Dmitry Osipenko wrote:
>>> 15.11.2019 15:52, Jon Hunter ÐÐÑÐÑ:
>>>>
>>>> On 13/11/2019 13:57, Dmitry Osipenko wrote:
>>>>> Hello Jon,
>>>>>
>>>>> 13.11.2019 09:52, Jon Hunter ÐÐÑÐÑ:
>>>>>>
>>>>>> On 24/10/2019 23:14, Dmitry Osipenko wrote:
>>>>>>> Utilize common Tegra30 CPU OPP table. CPU DVFS is available now on
>>>>>>> cardhu-a04.
>>>>>>>
>>>>>>> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
>>>>>>> ---
>>>>>>> arch/arm/boot/dts/tegra30-cardhu-a04.dts | 24 ++++++++++++++++++++++++
>>>>>>> 1 file changed, 24 insertions(+)
>>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
>>>>>>> index 0d71925d4f0b..9234988624ec 100644
>>>>>>> --- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts
>>>>>>> +++ b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
>>>>>>> @@ -2,6 +2,8 @@
>>>>>>> /dts-v1/;
>>>>>>>
>>>>>>> #include "tegra30-cardhu.dtsi"
>>>>>>> +#include "tegra30-cpu-opp.dtsi"
>>>>>>> +#include "tegra30-cpu-opp-microvolt.dtsi"
>>>>>>>
>>>>>>> /* This dts file support the cardhu A04 and later versions of board */
>>>>>>>
>>>>>>> @@ -127,4 +129,26 @@
>>>>>>> nvidia,tegra-core-regulator;
>>>>>>> };
>>>>>>> };
>>>>>>> +
>>>>>>> + cpus {
>>>>>>> + cpu0: cpu@0 {
>>>>>>> + cpu-supply = <&vddctrl_reg>;
>>>>>>> + operating-points-v2 = <&cpu0_opp_table>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + cpu@1 {
>>>>>>> + cpu-supply = <&vddctrl_reg>;
>>>>>>> + operating-points-v2 = <&cpu0_opp_table>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + cpu@2 {
>>>>>>> + cpu-supply = <&vddctrl_reg>;
>>>>>>> + operating-points-v2 = <&cpu0_opp_table>;
>>>>>>> + };
>>>>>>> +
>>>>>>> + cpu@3 {
>>>>>>> + cpu-supply = <&vddctrl_reg>;
>>>>>>> + operating-points-v2 = <&cpu0_opp_table>;
>>>>>>> + };
>>>>>>> + };
>>>>>>> };
>>>>>>
>>>>>> Sorry for not testing this sooner, but this is generating the
>>>>>> following WARNING on boot ...
>>>>>>
>>>>>> [ 2.916019] ------------[ cut here ]------------
>>>>>> [ 2.920669] WARNING: CPU: 2 PID: 1 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/opp/of.c:688 _of_add_opp_table_v2.part.2+0x45c/0x4d4
>>>>>> [ 2.933713] Modules linked in:
>>>>>> [ 2.936785] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc7-next-20191112-gfc6d6db1df2c #1
>>>>>> [ 2.945403] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
>>>>>> [ 2.951706] [<c0112924>] (unwind_backtrace) from [<c010c9d0>] (show_stack+0x10/0x14)
>>>>>> [ 2.959467] [<c010c9d0>] (show_stack) from [<c0aa4494>] (dump_stack+0xc0/0xd4)
>>>>>> [ 2.966707] [<c0aa4494>] (dump_stack) from [<c0124750>] (__warn+0xe0/0xf8)
>>>>>> [ 2.973593] [<c0124750>] (__warn) from [<c0124818>] (warn_slowpath_fmt+0xb0/0xb8)
>>>>>> [ 2.981090] [<c0124818>] (warn_slowpath_fmt) from [<c0754be0>] (_of_add_opp_table_v2.part.2+0x45c/0x4d4)
>>>>>> [ 2.990583] [<c0754be0>] (_of_add_opp_table_v2.part.2) from [<c0754c98>] (dev_pm_opp_of_add_table+0x40/0x15c)
>>>>>> [ 3.000508] [<c0754c98>] (dev_pm_opp_of_add_table) from [<c0754de8>] (dev_pm_opp_of_cpumask_add_table+0x34/0xb4)
>>>>>> [ 3.010704] [<c0754de8>] (dev_pm_opp_of_cpumask_add_table) from [<c075b058>] (cpufreq_init+0xf8/0x2cc)
>>>>>> [ 3.020024] [<c075b058>] (cpufreq_init) from [<c0758758>] (cpufreq_online+0x260/0x824)
>>>>>> [ 3.027953] [<c0758758>] (cpufreq_online) from [<c0758d98>] (cpufreq_add_dev+0x6c/0x78)
>>>>>> [ 3.035976] [<c0758d98>] (cpufreq_add_dev) from [<c05b3188>] (subsys_interface_register+0xa0/0xec)
>>>>>> [ 3.044951] [<c05b3188>] (subsys_interface_register) from [<c07574d4>] (cpufreq_register_driver+0x14c/0x20c)
>>>>>> [ 3.054792] [<c07574d4>] (cpufreq_register_driver) from [<c075aee0>] (dt_cpufreq_probe+0x94/0x114)
>>>>>> [ 3.063771] [<c075aee0>] (dt_cpufreq_probe) from [<c05b6a88>] (platform_drv_probe+0x48/0x98)
>>>>>> [ 3.072225] [<c05b6a88>] (platform_drv_probe) from [<c05b4a38>] (really_probe+0x234/0x34c)
>>>>>> [ 3.080502] [<c05b4a38>] (really_probe) from [<c05b4cc8>] (driver_probe_device+0x60/0x168)
>>>>>> [ 3.088780] [<c05b4cc8>] (driver_probe_device) from [<c05b4f78>] (device_driver_attach+0x58/0x60)
>>>>>> [ 3.097664] [<c05b4f78>] (device_driver_attach) from [<c05b5000>] (__driver_attach+0x80/0xbc)
>>>>>> [ 3.106200] [<c05b5000>] (__driver_attach) from [<c05b2db0>] (bus_for_each_dev+0x74/0xb4)
>>>>>> [ 3.114389] [<c05b2db0>] (bus_for_each_dev) from [<c05b3da4>] (bus_add_driver+0x164/0x1e8)
>>>>>> [ 3.122666] [<c05b3da4>] (bus_add_driver) from [<c05b5b54>] (driver_register+0x7c/0x114)
>>>>>> [ 3.130774] [<c05b5b54>] (driver_register) from [<c010306c>] (do_one_initcall+0x54/0x2a8)
>>>>>> [ 3.138974] [<c010306c>] (do_one_initcall) from [<c0f01040>] (kernel_init_freeable+0x14c/0x1e8)
>>>>>> [ 3.147695] [<c0f01040>] (kernel_init_freeable) from [<c0abbe88>] (kernel_init+0x8/0x10c)
>>>>>> [ 3.155887] [<c0abbe88>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
>>>>>> [ 3.163462] Exception stack(0xef0c9fb0 to 0xef0c9ff8)
>>>>>> [ 3.168519] 9fa0: 00000000 00000000 00000000 00000000
>>>>>> [ 3.176706] 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
>>>>>> [ 3.184893] 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
>>>>>> [ 3.191695] ---[ end trace a7dc36f7a4ddbdb2 ]---
>>>>>> [ 3.197855] ------------[ cut here ]------------
>>>>>>
>>>>>> Let me know if you can take a look at this.
>>>>>
>>>>> The warning happens because Cardhu now has CPU OPPs in the device-tree,
>>>>> but supported_hw isn't set for the OPPs and thus the count of available
>>>>> OPPs is 0.
>>>>>
>>>>> This is expected to happen because patch "cpufreq: tegra20: Use generic
>>>>> cpufreq-dt driver (Tegra30 supported now)" isn't applied yet.
>>>>>
>>>>> It is possible to factor out the blacklisting of Tegra SoCs in
>>>>> cpufreq_dt_platdev_init() into a separate patch and request backporting
>>>>> of that change in order to avoid the warning noise for older kernel
>>>>> versions + newer device-tree. Please let me know if you think that it's
>>>>> worth to do the separation.
>>>>
>>>> Unfortunately, I think we are going to need to drop this patch. Booting
>>>> Tegra30-cardhu-a04 with Thierry's for-5.5/arm/dt branch does not even
>>>> boot. There is no crash log but it hangs on boot. This patch appears to
>>>> be the culprit. What is odd is that Tegra30-cardhu-a04 boots fine with
>>>> Thierry's for-next branch which includes this. However, this is causing
>>>> lots of bisect problems. Updating the DT shouldn't break the boot.
>>> The diff between "for-5.5/arm/dt" and "for-next" is quite small, you
>>> only need to try to revert one or two patches. Seems the only major
>>> change which could be somehow related to CPUFreq is that
>>> "for-5.5/arm/dt" doesn't have regulators coupling support, but I don't
>>> see how it could cause any effect since CPUFreq just doesn't load due to
>>> a missing setup of supported_hw.
>>>
>>> Unfortunately for now I can't reproduce the hang with a similar setup
>>> that has OPPs in DT, doesn't have Tegra CPUFreq driver, doesn't
>>> blacklist Tegra in cpufreq-dt-platdev.c and doesn't have regulators
>>> coupling. I see the warning splats on boot and everything appears to be
>>> working fine.
>>>
>>> It's likely that the hang is caused by something else than this patch.
>>
>> No, it is definitely this patch. 100% reproducible.
>>
>>> It's also a bit odd that you're accusing this patch while apparently it
>>> worked a day before.
>>
>> No, the behaviour on top of -next is different to the "for-5.5/arm/dt"
>> branch, which is what I am saying.
>>
>>> Please give a try to the recent upstream linux-next. If it works, then
>>> probably there is nothing to worry about.
>>
>> No, there is plenty to be concerned about, with the latest -next we are
>> getting these WARN splats on boot, which we need to avoid.
>>
>>> I'll factor out the blacklisting change and add it as a separate patch
>>> into the next revision of the series, marking the patch as "fixes" and
>>> "stable" in order to get rid of the warning on stable kernels.
>>>
>>> I'm also fine with reverting of the DT changes for now, if you prefer
>>> that. But again, this DT change shouldn't cause any critical problems.
>>
>> No it should not, but it does.
>>
>>> I need a detailed report or a way to reproduce the problem in order to
>>> solve it, please try to collect some more details. Try to compile the
>>> cpufreq-dt driver as a loadable module, enable tracing of clk and
>>> regulator events (tp_printk
>>> trace_event=regulator_set_voltage,clk_set_rate,clk_set_parent).
>>
>> I add some debug prints and on boot with "for-5.5/arm/dt" is dies while
>> bringing CPU0 online for cpufreq ...
>>
>> [ 2.863369] cpufreq_dt: dt_cpufreq_probe-347
>> [ 2.867917] cpufreq_dt: dt_cpufreq_probe-360
>> [ 2.872195] cpufreq_dt: dt_cpufreq_probe-370
>> [ 2.876509] cpufreq: cpufreq_register_driver-2632
>> [ 2.881219] cpufreq: cpufreq_register_driver-2636
>> [ 2.885989] cpufreq: trying to register driver cpufreq-dt
>> [ 2.891395] cpufreq: cpufreq_register_driver-2651
>> [ 2.896131] cpufreq: cpufreq_register_driver-2661
>> [ 2.900839] cpufreq: cpufreq_register_driver-2665
>> [ 2.905610] cpufreq: cpufreq_register_driver-2672
>> [ 2.910329] cpu cpu0: cpufreq_add_dev: adding CPU0
>> [ 2.915152] cpufreq: cpufreq_online: bringing CPU0 online
>>
>> So I think it is best to revert this for now.
>
> I managed to reproduced the problem using unmodified "for-5.5/arm/dt":
>
> # modprobe cpufreq-dt
>
> [ 41.002512] regulator_set_voltage: name=vdd_core (1100000-1350000)
> [ 41.007822] regulator_set_voltage: name=vdd_core (1000000-1350000)
> [ 41.012475] regulator_set_voltage: name=vdd_cpu (925000-1250000)
> [ 41.017299] regulator_set_voltage: name=vdd_cpu (825000-1250000)
> [ 41.021842] regulator_set_voltage: name=vdd_core (950000-1350000)
> [ 41.025399] regulator_set_voltage: name=vdd_cpu (800000-1250000)
>
> As you can see the voltage drops too much and I know what causes it. The
> OPP core was getting some fixes recently, while "for-5.5/arm/dt" uses
> older 5.4-rc1 as the base. The problem was introduced in 5.4-rc1 and
> then it was fixed by the commit [1] in 5.4-rc5.

OK, great. Thanks for tracking this down.

> [1]
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/opp?h=v5.4-rc5&id=24957db1004353346583c9cc6d783db8f213e3ad
>
> The "for-next" branch has Tegra30 regulators coupling support and I
> actually worked around that OPP-core problem in the Tegra's coupler back
> in July [2] (see changelog). That explains why "for-next" branch works.
>
> [2] https://lkml.org/lkml/2019/7/25/892
>
> Thus the DT patch doesn't cause any problems. It just happened that the
> DT patch is a victim of the 5.4-rc1 OPP-core problem that is already
> fixed in rc5.

OK, and so that explains what I am seeing.

> Jon, anyways thank you for the heads-up. I'll add a patch to blacklist
> the cpufreq-dt-platdev in the next iteration to silence the warnings.

Yes if we could get the WARN fixed-up, that would make me happy :-)

Cheers!
Jon

--
nvpublic

Next message: Jerome Brunet: "Re: [PATCH v3 0/2] add the DDR clock controller on Meson8 and Meson8b"
Previous message: Bean Huo (beanhuo): "RE: [EXT] [PATCH v2 4/4] scsi: ufs: Complete pending requests in host reset and restore path"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]