Re: [PATCH v6 1/5] dt-bindings: power: avs: Add support for CPR (Core Power Reduction)

[Bjorn Andersson]

On Tue 19 Nov 07:46 PST 2019, Niklas Cassel wrote:

> Add DT bindings to describe the CPR HW found on certain Qualcomm SoCs.
> 
> Co-developed-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@xxxxxxxxxx>
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@xxxxxxxxxx>
> Signed-off-by: Niklas Cassel <niklas.cassel@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>

Reviewed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>

Regards,
Bjorn

> ---
> Changes since v5:
> -None
> 
>  .../bindings/power/avs/qcom,cpr.txt           | 130 ++++++++++++++++++
>  1 file changed, 130 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
> 
> diff --git a/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt b/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
> new file mode 100644
> index 000000000000..ab0d5ebbad4e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/avs/qcom,cpr.txt
> @@ -0,0 +1,130 @@
> +QCOM CPR (Core Power Reduction)
> +
> +CPR (Core Power Reduction) is a technology to reduce core power on a CPU
> +or other device. Each OPP of a device corresponds to a "corner" that has
> +a range of valid voltages for a particular frequency. While the device is
> +running at a particular frequency, CPR monitors dynamic factors such as
> +temperature, etc. and suggests adjustments to the voltage to save power
> +and meet silicon characteristic requirements.
> +
> +- compatible:
> +	Usage: required
> +	Value type: <string>
> +	Definition: should be "qcom,qcs404-cpr", "qcom,cpr" for qcs404
> +
> +- reg:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: base address and size of the rbcpr register region
> +
> +- interrupts:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify the CPR interrupt
> +
> +- clocks:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: phandle to the reference clock
> +
> +- clock-names:
> +	Usage: required
> +	Value type: <stringlist>
> +	Definition: must be "ref"
> +
> +- vdd-apc-supply:
> +	Usage: required
> +	Value type: <phandle>
> +	Definition: phandle to the vdd-apc-supply regulator
> +
> +- #power-domain-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: should be 0
> +
> +- operating-points-v2:
> +	Usage: required
> +	Value type: <phandle>
> +	Definition: A phandle to the OPP table containing the
> +		    performance states supported by the CPR
> +		    power domain
> +
> +- acc-syscon:
> +	Usage: optional
> +	Value type: <phandle>
> +	Definition: phandle to syscon for writing ACC settings
> +
> +- nvmem-cells:
> +	Usage: required
> +	Value type: <phandle>
> +	Definition: phandle to nvmem cells containing the data
> +		    that makes up a fuse corner, for each fuse corner.
> +		    As well as the CPR fuse revision.
> +
> +- nvmem-cell-names:
> +	Usage: required
> +	Value type: <stringlist>
> +	Definition: should be "cpr_quotient_offset1", "cpr_quotient_offset2",
> +		    "cpr_quotient_offset3", "cpr_init_voltage1",
> +		    "cpr_init_voltage2", "cpr_init_voltage3", "cpr_quotient1",
> +		    "cpr_quotient2", "cpr_quotient3", "cpr_ring_osc1",
> +		    "cpr_ring_osc2", "cpr_ring_osc3", "cpr_fuse_revision"
> +		    for qcs404.
> +
> +Example:
> +
> +	cpr_opp_table: cpr-opp-table {
> +		compatible = "operating-points-v2-qcom-level";
> +
> +		cpr_opp1: opp1 {
> +			opp-level = <1>;
> +			qcom,opp-fuse-level = <1>;
> +		};
> +		cpr_opp2: opp2 {
> +			opp-level = <2>;
> +			qcom,opp-fuse-level = <2>;
> +		};
> +		cpr_opp3: opp3 {
> +			opp-level = <3>;
> +			qcom,opp-fuse-level = <3>;
> +		};
> +	};
> +
> +	power-controller@b018000 {
> +		compatible = "qcom,qcs404-cpr", "qcom,cpr";
> +		reg = <0x0b018000 0x1000>;
> +		interrupts = <0 15 IRQ_TYPE_EDGE_RISING>;
> +		clocks = <&xo_board>;
> +		clock-names = "ref";
> +		vdd-apc-supply = <&pms405_s3>;
> +		#power-domain-cells = <0>;
> +		operating-points-v2 = <&cpr_opp_table>;
> +		acc-syscon = <&tcsr>;
> +
> +		nvmem-cells = <&cpr_efuse_quot_offset1>,
> +			<&cpr_efuse_quot_offset2>,
> +			<&cpr_efuse_quot_offset3>,
> +			<&cpr_efuse_init_voltage1>,
> +			<&cpr_efuse_init_voltage2>,
> +			<&cpr_efuse_init_voltage3>,
> +			<&cpr_efuse_quot1>,
> +			<&cpr_efuse_quot2>,
> +			<&cpr_efuse_quot3>,
> +			<&cpr_efuse_ring1>,
> +			<&cpr_efuse_ring2>,
> +			<&cpr_efuse_ring3>,
> +			<&cpr_efuse_revision>;
> +		nvmem-cell-names = "cpr_quotient_offset1",
> +			"cpr_quotient_offset2",
> +			"cpr_quotient_offset3",
> +			"cpr_init_voltage1",
> +			"cpr_init_voltage2",
> +			"cpr_init_voltage3",
> +			"cpr_quotient1",
> +			"cpr_quotient2",
> +			"cpr_quotient3",
> +			"cpr_ring_osc1",
> +			"cpr_ring_osc2",
> +			"cpr_ring_osc3",
> +			"cpr_fuse_revision";
> +	};
> -- 
> 2.23.0
>