[PATCH v4 2/2] PCI: dwc: add support to handle ZRX-DC Compliant PHYs

[Anvesh Salveru]

Many platforms use DesignWare controller but the PHY can be different in
different platforms. If the PHY is compliant is to ZRX-DC specification
it helps in low power consumption during power states.

If current data rate is 8.0 GT/s or higher and PHY is not compliant to
ZRX-DC specification, then after every 100ms link should transition to
recovery state during the low power states.

DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.

Platforms with ZRX-DC compliant PHY can set phy_zrxdc_compliant variable
to specify this property to the controller.

Signed-off-by: Anvesh Salveru <anvesh.s@xxxxxxxxxxx>
Signed-off-by: Pankaj Dubey <pankaj.dubey@xxxxxxxxxxx>
---
 drivers/pci/controller/dwc/pcie-designware.c | 6 ++++++
 drivers/pci/controller/dwc/pcie-designware.h | 4 ++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 820488d..36a01b7 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -556,4 +556,10 @@ void dw_pcie_setup(struct dw_pcie *pci)
 		       PCIE_PL_CHK_REG_CHK_REG_START;
 		dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS, val);
 	}
+
+	if (pci->phy_zrxdc_compliant) {
+		val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
+		val &= ~PORT_LOGIC_GEN3_ZRXDC_NONCOMPL;
+		dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
+	}
 }
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index 5a18e94..f43f986 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -60,6 +60,9 @@
 #define PCIE_MSI_INTR0_MASK		0x82C
 #define PCIE_MSI_INTR0_STATUS		0x830
 
+#define PCIE_PORT_GEN3_RELATED		0x890
+#define PORT_LOGIC_GEN3_ZRXDC_NONCOMPL	BIT(0)
+
 #define PCIE_ATU_VIEWPORT		0x900
 #define PCIE_ATU_REGION_INBOUND		BIT(31)
 #define PCIE_ATU_REGION_OUTBOUND	0
@@ -249,6 +252,7 @@ struct dw_pcie {
 	void __iomem		*atu_base;
 	u32			num_viewport;
 	u8			iatu_unroll_enabled;
+	bool			phy_zrxdc_compliant;
 	struct pcie_port	pp;
 	struct dw_pcie_ep	ep;
 	const struct dw_pcie_ops *ops;
-- 
2.7.4