[PATCH v5 4/5] scsi: ufs: Do not clear the DL layer timers

[Can Guo]

During power mode change, PACP_PWR_Req frame sends
PAPowerModeUserData parameters (and they are considered valid by device if
Flags[4] - UserDataValid bit is set in the same frame).
Currently we don't set these PAPowerModeUserData parameters and hardware
always sets UserDataValid bit which would clear all the DL layer timeout
values of the peer device after the power mode change.

This change sets the PAPowerModeUserData[0..5] to UniPro specification
recommended default values, in addition we are also setting the relevant
DME_LOCAL_* timer attributes as required by UFS HCI specification.

Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
Reviewed-by Avri Altman <avri.altman@xxxxxxx>
Reviewed-by: Bean Huo <beanhuo@xxxxxxxxxx>
---
 drivers/scsi/ufs/ufshcd.c | 20 ++++++++++++++++++++
 drivers/scsi/ufs/unipro.h | 11 +++++++++++
 2 files changed, 31 insertions(+)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 9e44506..086d359 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4084,6 +4084,26 @@ static int ufshcd_change_power_mode(struct ufs_hba *hba,
 		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HSSERIES),
 						pwr_mode->hs_rate);
 
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
+			DL_FC0ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
+			DL_TC0ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
+			DL_AFC0ReqTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
+			DL_FC1ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
+			DL_TC1ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
+			DL_AFC1ReqTimeOutVal_Default);
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
+			DL_FC0ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
+			DL_TC0ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
+			DL_AFC0ReqTimeOutVal_Default);
+
 	ret = ufshcd_uic_change_pwr_mode(hba, pwr_mode->pwr_rx << 4
 			| pwr_mode->pwr_tx);
 
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
index f539f87..3dc4d8b 100644
--- a/drivers/scsi/ufs/unipro.h
+++ b/drivers/scsi/ufs/unipro.h
@@ -161,6 +161,17 @@
 /* PHY Adapter Protocol Constants */
 #define PA_MAXDATALANES	4
 
+#define DL_FC0ProtectionTimeOutVal_Default	8191
+#define DL_TC0ReplayTimeOutVal_Default		65535
+#define DL_AFC0ReqTimeOutVal_Default		32767
+#define DL_FC1ProtectionTimeOutVal_Default	8191
+#define DL_TC1ReplayTimeOutVal_Default		65535
+#define DL_AFC1ReqTimeOutVal_Default		32767
+
+#define DME_LocalFC0ProtectionTimeOutVal	0xD041
+#define DME_LocalTC0ReplayTimeOutVal		0xD042
+#define DME_LocalAFC0ReqTimeOutVal		0xD043
+
 /* PA power modes */
 enum {
 	FAST_MODE	= 1,
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project