[PATCH v3 1/2] dt-bindings: spi: Add schema for Cadence QSPI Controller driver

[Ramuthevar,Vadivel MuruganX]

From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>

Add dt-bindings documentation for Cadence-QSPI controller to support
spi based flash memories.

Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
---
 .../devicetree/bindings/spi/cadence,qspi.yaml      | 162 +++++++++++++++++++++
 1 file changed, 162 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/cadence,qspi.yaml

diff --git a/Documentation/devicetree/bindings/spi/cadence,qspi.yaml b/Documentation/devicetree/bindings/spi/cadence,qspi.yaml
new file mode 100644
index 000000000000..7756c34bb453
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cadence,qspi.yaml
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/spi/cadence,qspi.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: Cadence QSPI Flash Controller support
+
+maintainers:
+  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+description: |
+  Add support for the Cadence QSPI controller,This controller is
+  present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
+  has been tested On Intel's LGM SoC.
+
+  - compatible : should be one of the following:
+        Generic default - "cdns,qspi-nor".
+        For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
+        For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
+        For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
+
+properties:
+  compatible:
+    enum:
+      - cadence,qspi
+      - cdns,qspi-nor
+      - ti,k2g-qspi
+      - ti,am654-ospi
+      - intel,lgm-qspi
+
+  reg:
+    description: |
+      Contains two entries, each of which is a tuple consisting of a
+      Physical address and length. The first entry is the address and
+      length of the controller register set. The second entry is the
+      address and length of the QSPI Controller data area.
+
+  interrupts:
+    description:
+      Unit interrupt specifier for the controller interrupt.
+
+  clocks:
+    description:
+      phandle to the Quad SPI clock.
+
+  cdns,fifo-depth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Size of the data FIFO in words.
+
+  cdns,fifo-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Bus width of the data FIFO in bytes.
+
+  cdns,trigger-address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      32-bit indirect AHB trigger address.
+
+  cdns,is-decoded-cs:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Flag to indicate whether decoder is used or not.
+
+  cdns,rclk-en:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Flag to indicate that QSPI return clock is used to latch the read data
+      rather than the QSPI clock. Make sure that QSPI return clock is populated
+      on the board before using this property.
+
+  resets:
+    minItems: 1
+    maxItems: 2
+
+  reset-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      - const: qspi
+      - const: qspi-ocp
+
+# subnode's properties
+patternProperties:
+  "^.*@[0-9a-fA-F]+$":
+    type: object
+    description:
+      flash device uses the subnodes below defined properties.
+
+  cdns,read-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay for read capture logic, in clock cycles.
+
+  cdns,tshsl-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Delay in nanoseconds for the length that the master mode chip select
+      outputs are de-asserted between transactions.
+
+  cdns,tsd2d-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Delay in nanoseconds between one chip select being de-activated
+      and the activation of another.
+
+  cdns,tchsh-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Delay in nanoseconds between last bit of current transaction and
+      deasserting the device chip select (qspi_n_ss_out).
+
+  cdns,tslch-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      Delay in nanoseconds between setting qspi_n_ss_out low and
+      first bit transfer.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - cdns,is-decoded-cs
+  - cdns,fifo-depth
+  - cdns,fifo-width
+  - cdns,trigger-address
+  - resets
+  - reset-names
+
+examples:
+  - |
+    qspi: spi@ff705000 {
+          compatible = "cadence,qspi", "cdns,qspi-nor";
+          #address-cells = <1>;
+          #size-cells = <0>;
+          reg = <0xff705000 0x1000>,
+                <0xffa00000 0x1000>;
+          interrupts = <0 151 4>;
+          clocks = <&qspi_clk>;
+          cdns,is-decoded-cs;
+          cdns,fifo-depth = <128>;
+          cdns,fifo-width = <4>;
+          cdns,trigger-address = <0x00000000>;
+          resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
+          reset-names = "qspi", "qspi-ocp";
+
+          flash0: n25q00@0 {
+              ...
+              cdns,read-delay = <4>;
+              cdns,tshsl-ns = <50>;
+              cdns,tsd2d-ns = <50>;
+              cdns,tchsh-ns = <4>;
+              cdns,tslch-ns = <4>;
+          };
+    };
+
-- 
2.11.0