Re: [PATCH 11/14] ARM: dts: sun8i: r40: Add device node for CSI0

[Chen-Yu Tsai]

On Mon, Dec 16, 2019 at 9:39 PM Maxime Ripard <mripard@xxxxxxxxxx> wrote:
>
> On Mon, Dec 16, 2019 at 12:59:21AM +0800, Chen-Yu Tsai wrote:
> > From: Chen-Yu Tsai <wens@xxxxxxxx>
> >
> > The CSI0 and CSI1 blocks are the same as found on the A20. However only
> > CSI0 is supported upstream right now.
> >
> > Add a device node for CSI0 using the A20 compatible as a fallback, and
> > the standard pinctrl options. Also add the MBUS interconnect.
> >
> > Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> > ---
> >  arch/arm/boot/dts/sun8i-r40.dtsi | 36 ++++++++++++++++++++++++++++++++
> >  1 file changed, 36 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
> > index 82ea0b5b0710..2d1e97cc4155 100644
> > --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> > +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> > @@ -180,6 +180,20 @@ nmi_intc: interrupt-controller@1c00030 {
> >                       interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> >               };
> >
> > +             csi0: csi@1c09000 {
> > +                     compatible = "allwinner,sun8i-r40-csi0",
> > +                                  "allwinner,sun7i-a20-csi0";
> > +                     reg = <0x01c09000 0x1000>;
> > +                     interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> > +                     clocks = <&ccu CLK_BUS_CSI0>, <&ccu CLK_CSI_SCLK>,
> > +                              <&ccu CLK_DRAM_CSI0>;
> > +                     clock-names = "bus", "isp", "ram";
> > +                     resets = <&ccu RST_BUS_CSI0>;
> > +                     interconnects = <&mbus 5>;
> > +                     interconnect-names = "dma-mem";
> > +                     status = "disabled";
> > +             };
> > +
> >               mmc0: mmc@1c0f000 {
> >                       compatible = "allwinner,sun8i-r40-mmc",
> >                                    "allwinner,sun50i-a64-mmc";
> > @@ -355,6 +369,20 @@ clk_out_a_pin: clk-out-a-pin {
> >                               function = "clk_out_a";
> >                       };
> >
> > +                     /omit-if-no-ref/
> > +                     csi0_8bits_pins: csi0-8bits-pins {
> > +                             pins = "PE0", "PE2", "PE3", "PE4", "PE5",
> > +                                    "PE6", "PE7", "PE8", "PE9", "PE10",
> > +                                    "PE11";
> > +                             function = "csi0";
> > +                     };
> > +
> > +                     /omit-if-no-ref/
> > +                     csi0_mclk_pin: csi0-mclk-pin {
> > +                             pins = "PE1";
> > +                             function = "csi0";
> > +                     };
> > +
> >                       gmac_rgmii_pins: gmac-rgmii-pins {
> >                               pins = "PA0", "PA1", "PA2", "PA3",
> >                                      "PA4", "PA5", "PA6", "PA7",
> > @@ -624,6 +652,14 @@ gmac_mdio: mdio {
> >                       };
> >               };
> >
> > +             mbus: dram-controller@1c62000 {
> > +                     compatible = "allwinner,sun8i-r40-mbus";
> > +                     reg = <0x01c62000 0x1000>;
> > +                     clocks = <&ccu 155>;
>
> We should export the clock too?

I meant to do it separately. Haven't gotten to it though.

ChenYu