Re: [PATCH v2 2/3] dt-bindings: power: Add the bq2515x family dt bindings

[Sebastian Reichel]

Hi,

On Tue, Oct 29, 2019 at 03:02:00PM -0500, Dan Murphy wrote:
> Add the bindings for the bq25150 and bq25155 500mA
> charging ICs from Texas Instruments.
> 
> Datasheet:
> http://www.ti.com/lit/ds/symlink/bq25150.pdf
> http://www.ti.com/lit/ds/symlink/bq25155.pdf
> 
> Signed-off-by: Dan Murphy <dmurphy@xxxxxx>
> CC: Rob Herring <robh@xxxxxxxxxx>
> ---
> 
> v2 - Converted to yaml format and removed ti,* properties for already defined
> properties
> 
>  .../bindings/power/supply/bq2515x.yaml        | 85 +++++++++++++++++++
>  1 file changed, 85 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/power/supply/bq2515x.yaml
> 
> diff --git a/Documentation/devicetree/bindings/power/supply/bq2515x.yaml b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
> new file mode 100644
> index 000000000000..4e6225056f45
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/power/supply/bq2515x.yaml
> @@ -0,0 +1,85 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright (C) 2019 Texas Instruments Incorporated
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/power/supply/bq2515x.yaml#";
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#";
> +
> +title: TI bq2515x 500-mA Linear charger family
> +
> +maintainers:
> +  - Dan Murphy <dmurphy@xxxxxx>
> +
> +description: |
> +  The BQ2515x family is a highly integrated battery charge management IC that
> +  integrates the most common functions for wearable devices, namely a charger,
> +  an output voltage rail, ADC for battery and system monitoring, and
> +  push-button controller.
> +
> +  Specifications about the charger can be found at:
> +    http://www.ti.com/lit/ds/symlink/bq25150.pdf
> +    http://www.ti.com/lit/ds/symlink/bq25155.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ti,bq25150
> +      - ti,bq25155
> +
> +  reg:
> +    maxItems: 1
> +
> +  pg-gpios:
> +    description: |
> +       GPIO used for connecting the bq2515x device PG (Power Good)
> +       pin.  This pin should be used if possible as this is the
> +       recommended way to obtain the charger's input PG state.
> +       If this pin is not specified a software-based approach for PG
> +       detection is used.
> +
> +  reset-gpios:
> +    description: |
> +       GPIO used for hardware reset.
> +
> +  low-power-gpios:
> +    description: |
> +       GPIO used for low power mode of IC.
> +
> +  charge-enable-gpios:
> +    description: |
> +       GPIO used to turn on and off charging.

Above looks ok to me.

> +  constant-charge-current-max-microamp:
> +    description: |
> +       Maximum charging current in micro Amps.
> +    minimum: 50000
> +    maximum: 600000
> +
> +  voltage-max-design-microvolt:
> +    description: |
> +       Maximum charging voltage in micro volts.
> +    minimum: 3600000
> +    maximum: 4600000

These two should use the simple-battery binding, as seen in
Documentation/devicetree/bindings/power/supply/battery.txt

-- Sebastian

> +
> +required:
> +  - compatible
> +  - reg
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    i2c0 {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +      charger@6b {
> +          compatible = "ti,bq25150";
> +          reg = <0x6b>;
> +
> +          pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> +          reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
> +          low-power-gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
> +          charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
> +          constant-charge-current-max-microamp = <300000>;
> +          voltage-max-design-microvolt = <4200000>;
> +      };
> +    };
> -- 
> 2.22.0.214.g8dca754b1e
>

Attachment: signature.asc
Description: PGP signature