Re: [PATCH] ASoC: Add MediaTek MT6660 Speaker Amp Driver

[Mark Brown]

On Fri, Dec 20, 2019 at 06:15:34PM +0800, Jeff Chang wrote:

> +++ b/sound/soc/codecs/mt6660.c
> @@ -0,0 +1,653 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 MediaTek Inc.
> + */

Please make the entire comment a C++ one so things look more
intentional.

> +	{ MT6660_REG_DEVID, 2},
> +	{ MT6660_REG_TDM_CFG3, 2},
> +	{ MT6660_REG_HCLIP_CTRL, 2},
> +	{ MT6660_REG_DA_GAIN, 2},

Missing space before the } (the same thing happens in some of the
other tables).

> +static int mt6660_component_get_volsw(struct snd_kcontrol *kcontrol,
> +				  struct snd_ctl_elem_value *ucontrol)
> +{
> +	struct snd_soc_component *component =
> +		snd_soc_kcontrol_component(kcontrol);
> +	struct mt6660_chip *chip = (struct mt6660_chip *)
> +		snd_soc_component_get_drvdata(component);
> +	int ret = -EINVAL;
> +
> +	if (!strcmp(kcontrol->id.name, "Chip_Rev")) {

Why would this be used on a different control?

> +	SOC_SINGLE_EXT("BoostMode", MT6660_REG_BST_CTRL, 0, 3, 0,
> +		       snd_soc_get_volsw, snd_soc_put_volsw),

Boost Mode.  You've also got a lot of these controls that are _EXT but
you then just use standard operations so it's not clear why you're using
_EXT.

> +	SOC_SINGLE_EXT("audio input selection", MT6660_REG_DATAO_SEL, 6, 3, 0,
> +		       snd_soc_get_volsw, snd_soc_put_volsw),

Audio Input Selection, but this looks like it should be a DAPM control
if it's controlling audio routing.  A simple numerical setting
definitely doesn't seem like the right thing.

> +	SOC_SINGLE_EXT("AUD LOOP BACK Switch", MT6660_REG_PATH_BYPASS, 4, 1, 0,
> +		       snd_soc_get_volsw, snd_soc_put_volsw),

This sounds like it should be a DAPM thing too.

> +static int mt6660_component_probe(struct snd_soc_component *component)
> +{
> +	struct mt6660_chip *chip = snd_soc_component_get_drvdata(component);
> +	int ret = 0;
> +
> +	dev_info(component->dev, "%s\n", __func__);

dev_dbg() at most but probably better to remove this and the other
similar dev_info()s.

> +static inline int _mt6660_chip_id_check(struct mt6660_chip *chip)
> +{
> +	u8 id[2] = {0};
> +	int ret = 0;
> +
> +	ret = i2c_smbus_read_i2c_block_data(chip->i2c, MT6660_REG_DEVID, 2, id);
> +	if (ret < 0)
> +		return ret;
> +	ret = (id[0] << 8) + id[1];
> +	ret &= 0x0ff0;
> +	if (ret != 0x00e0 && ret != 0x01e0)
> +		return -ENODEV;

It'd be better to print an error message saying we don't recognize the
device to help people doing debugging.

> +	if (of_property_read_u32(np, "rt,init_setting_num", &val)) {
> +		dev_info(dev, "no init setting\n");
> +		chip->plat_data.init_setting_num = 0;

You should be adding a DT binding document for any new DT bindings.

Attachment: signature.asc
Description: PGP signature