Re: [PATCH v2 1/3] phy: amlogic: Add Amlogic AXG MIPI/PCIE PHY Driver

[Jerome Brunet]

On Tue 24 Dec 2019 at 17:30, Remi Pommarel <repk@xxxxxxxxxxxx> wrote:

> On Tue, Dec 24, 2019 at 03:40:20PM +0530, Kishon Vijay Abraham I wrote:
>> Hi,
>> 
>> On 24/12/19 3:15 AM, Remi Pommarel wrote:
>> > This adds support for the MIPI PHY also needed for PCIE found in the
>> > Amlogic AXG SoC Family.
>> > 
>> > MIPI or PCIE selection is done by the #phy-cells, making the mode
>> > static and exclusive.
>> > 
>> > For now only PCIE fonctionality is supported.
>> > 
>> > This PHY will be used to replace the mipi_enable clock gating logic
>> > which was mistakenly added in the clock subsystem. This also activate
>> > a non documented band gap bit in those registers that allows reliable
>> > PCIE clock signal generation on AXG platforms.
>> > 
>> > Signed-off-by: Remi Pommarel <repk@xxxxxxxxxxxx>
>> > ---
>> >  drivers/phy/amlogic/Kconfig                   |  11 ++
>> >  drivers/phy/amlogic/Makefile                  |   1 +
>> >  drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c | 176 ++++++++++++++++++
>> >  3 files changed, 188 insertions(+)
>> >  create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
>> > 
>> > diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
>> > index af774ac2b934..1eeb75d018e3 100644
>> > --- a/drivers/phy/amlogic/Kconfig
>> > +++ b/drivers/phy/amlogic/Kconfig
>> > @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
>> >  	  Enable this to support the Meson USB3 + PCIE Combo PHY found
>> >  	  in Meson G12A SoCs.
>> >  	  If unsure, say N.
>> > +
>> > +config PHY_MESON_AXG_MIPI_PCIE
>> > +	tristate "Meson AXG MIPI + PCIE PHY driver"
>> > +	default ARCH_MESON
>> > +	depends on OF && (ARCH_MESON || COMPILE_TEST)
>> > +	select GENERIC_PHY
>> > +	select MFD_SYSCON
>> > +	help
>> > +	  Enable this to support the Meson MIPI + PCIE PHY found
>> > +	  in Meson AXG SoCs.
>> > +	  If unsure, say N.
>> > diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
>> > index 11d1c42ac2be..2167330a0ae8 100644
>> > --- a/drivers/phy/amlogic/Makefile
>> > +++ b/drivers/phy/amlogic/Makefile
>> > @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_MESON_GXL_USB2)	+= phy-meson-gxl-usb2.o
>> >  obj-$(CONFIG_PHY_MESON_G12A_USB2)	+= phy-meson-g12a-usb2.o
>> >  obj-$(CONFIG_PHY_MESON_GXL_USB3)	+= phy-meson-gxl-usb3.o
>> >  obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE)	+= phy-meson-g12a-usb3-pcie.o
>> > +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE)	+= phy-meson-axg-mipi-pcie.o
>> > diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
>> > new file mode 100644
>> > index 000000000000..006aa8cdfc47
>> > --- /dev/null
>> > +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie.c
>> > @@ -0,0 +1,176 @@
>> > +// SPDX-License-Identifier: GPL-2.0
>> > +/*
>> > + * Amlogic AXG MIPI + PCIE PHY driver
>> > + *
>> > + * Copyright (C) 2019 Remi Pommarel <repk@xxxxxxxxxxxx>
>> > + */
>> > +#include <linux/module.h>
>> > +#include <linux/phy/phy.h>
>> > +#include <linux/regmap.h>
>> > +#include <linux/mfd/syscon.h>
>> > +#include <linux/platform_device.h>
>> > +#include <dt-bindings/phy/phy.h>
>> > +
>> > +#define HHI_MIPI_CNTL0 0x00
>> > +#define		HHI_MIPI_CNTL0_COMMON_BLOCK	GENMASK(31, 28)
>> > +#define		HHI_MIPI_CNTL0_ENABLE		BIT(29)
>> > +#define		HHI_MIPI_CNTL0_BANDGAP		BIT(26)
>> > +#define		HHI_MIPI_CNTL0_DECODE_TO_RTERM	GENMASK(15, 12)
>> > +#define		HHI_MIPI_CNTL0_OUTPUT_EN	BIT(3)
>> > +
>> > +#define HHI_MIPI_CNTL1 0x01
>> > +#define		HHI_MIPI_CNTL1_CH0_CML_PDR_EN	BIT(12)
>> > +#define		HHI_MIPI_CNTL1_LP_ABILITY	GENMASK(5, 4)
>> > +#define		HHI_MIPI_CNTL1_LP_RESISTER	BIT(3)
>> > +#define		HHI_MIPI_CNTL1_INPUT_SETTING	BIT(2)
>> > +#define		HHI_MIPI_CNTL1_INPUT_SEL	BIT(1)
>> > +#define		HHI_MIPI_CNTL1_PRBS7_EN		BIT(0)
>> > +
>> > +#define HHI_MIPI_CNTL2 0x02
>> > +#define		HHI_MIPI_CNTL2_CH_PU		GENMASK(31, 25)
>> > +#define		HHI_MIPI_CNTL2_CH_CTL		GENMASK(24, 19)
>> > +#define		HHI_MIPI_CNTL2_CH0_DIGDR_EN	BIT(18)
>> > +#define		HHI_MIPI_CNTL2_CH_DIGDR_EN	BIT(17)
>> > +#define		HHI_MIPI_CNTL2_LPULPS_EN	BIT(16)
>> > +#define		HHI_MIPI_CNTL2_CH_EN(n)		BIT(15 - (n))
>> > +#define		HHI_MIPI_CNTL2_CH0_LP_CTL	GENMASK(10, 1)
>> > +
>> > +struct phy_axg_mipi_pcie_priv {
>> > +	struct phy *phy;
>> > +	unsigned int mode;
>> > +	struct regmap *regmap;
>> > +};
>> > +
>> > +static const struct regmap_config phy_axg_mipi_pcie_regmap_conf = {
>> > +	.reg_bits = 8,
>> > +	.val_bits = 32,
>> > +	.reg_stride = 4,
>> > +	.max_register = HHI_MIPI_CNTL2,
>> > +};
>> > +
>> > +static int phy_axg_mipi_pcie_power_on(struct phy *phy)
>> > +{
>> > +	struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy);
>> > +
>> > +	/* MIPI not supported yet */
>> > +	if (priv->mode != PHY_TYPE_PCIE)
>> > +		return 0;
>> > +
>> > +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> > +			   HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
>> > +
>> > +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> > +			   HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
>> > +	return 0;
>> > +}
>> > +
>> > +static int phy_axg_mipi_pcie_power_off(struct phy *phy)
>> > +{
>> > +	struct phy_axg_mipi_pcie_priv *priv = phy_get_drvdata(phy);
>> > +
>> > +	/* MIPI not supported yet */
>> > +	if (priv->mode != PHY_TYPE_PCIE)
>> > +		return 0;
>> > +
>> > +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> > +			   HHI_MIPI_CNTL0_BANDGAP, 0);
>> > +	regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
>> > +			   HHI_MIPI_CNTL0_ENABLE, 0);
>> > +	return 0;
>> > +}
>> > +
>> > +static int phy_axg_mipi_pcie_init(struct phy *phy)
>> > +{
>> > +	return 0;
>> > +}
>> > +
>> > +static int phy_axg_mipi_pcie_exit(struct phy *phy)
>> > +{
>> > +	return 0;
>> > +}
>> > +
>> > +static const struct phy_ops phy_axg_mipi_pcie_ops = {
>> > +	.init = phy_axg_mipi_pcie_init,
>> > +	.exit = phy_axg_mipi_pcie_exit,
>> > +	.power_on = phy_axg_mipi_pcie_power_on,
>> > +	.power_off = phy_axg_mipi_pcie_power_off,
>> > +	.owner = THIS_MODULE,
>> > +};
>> > +
>> > +static struct phy *phy_axg_mipi_pcie_xlate(struct device *dev,
>> > +					   struct of_phandle_args *args)
>> > +{
>> > +	struct phy_axg_mipi_pcie_priv *priv = dev_get_drvdata(dev);
>> > +	unsigned int mode;
>> > +
>> > +	if (args->args_count != 1) {
>> > +		dev_err(dev, "invalid number of arguments\n");
>> > +		return ERR_PTR(-EINVAL);
>> > +	}
>> > +
>> > +	mode = args->args[0];
>> > +
>> > +	/* MIPI mode is not supported yet */
>> > +	if (mode != PHY_TYPE_PCIE) {
>> > +		dev_err(dev, "invalid phy mode select argument\n");
>> > +		return ERR_PTR(-EINVAL);
>> > +	}
>> > +
>> > +	priv->mode = mode;
>> > +	return priv->phy;
>> > +}
>> > +
>> > +static int phy_axg_mipi_pcie_probe(struct platform_device *pdev)
>> > +{
>> > +	struct phy_provider *pphy;
>> > +	struct device *dev = &pdev->dev;
>> > +	struct phy_axg_mipi_pcie_priv *priv;
>> > +	struct device_node *np = dev->of_node;
>> > +	int ret;
>> > +
>> > +	priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
>> > +	if (!priv)
>> > +		return -ENOMEM;
>> > +
>> > +	/* Get the hhi system controller node */
>> > +	priv->regmap = syscon_node_to_regmap(of_get_parent(dev->of_node));
>> > +	if (IS_ERR(priv->regmap)) {
>> > +		dev_err(dev, "failed to get HHI regmap\n");
>> > +		return PTR_ERR(priv->regmap);
>> > +	}
>> > +
>> > +	priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_ops);
>> > +	if (IS_ERR(priv->phy)) {
>> > +		ret = PTR_ERR(priv->phy);
>> > +		if (ret != -EPROBE_DEFER)
>> > +			dev_err(dev, "failed to create PHY\n");
>> > +		return ret;
>> > +	}
>> > +
>> > +	phy_set_drvdata(priv->phy, priv);
>> > +	dev_set_drvdata(dev, priv);
>> > +	pphy = devm_of_phy_provider_register(dev, phy_axg_mipi_pcie_xlate);
>> > +
>> > +	return PTR_ERR_OR_ZERO(pphy);
>> > +}
>> > +
>> > +static const struct of_device_id phy_axg_mipi_pcie_of_match[] = {
>> > +	{
>> > +		.compatible = "amlogic,axg-mipi-pcie-phy",
>> 
>> Is there a dt-binding documentation for this?
>
> There is binding documentation updates for this whole serie but I thought
> they were supposed to be sent in separate serie, which is not the case
> apparently.

Different patches, but same series is recommended ;)

>
> Thanks,