Re: [PATCH v4 05/12] dt-bindings: soc: Add Aspeed XDMA Engine

[Andrew Jeffery]

On Fri, 3 Jan 2020, at 05:57, Eddie James wrote:
> Document the bindings for the Aspeed AST25XX and AST26XX XDMA engine.
> 
> Signed-off-by: Eddie James <eajames@xxxxxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> Changes since v3:
>  - Switch "scu" property to "aspeed,scu"
> 
>  .../devicetree/bindings/soc/aspeed/xdma.txt   | 40 +++++++++++++++++++
>  MAINTAINERS                                   |  6 +++
>  2 files changed, 46 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/soc/aspeed/xdma.txt
> 
> diff --git a/Documentation/devicetree/bindings/soc/aspeed/xdma.txt 
> b/Documentation/devicetree/bindings/soc/aspeed/xdma.txt
> new file mode 100644
> index 000000000000..e0740ccfa910
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/aspeed/xdma.txt
> @@ -0,0 +1,40 @@
> +Aspeed AST25XX and AST26XX XDMA Engine
> +
> +The XDMA Engine embedded in the AST2500 and AST2600 SOCs can perform 
> automatic
> +DMA operations over PCI between the SOC (acting as a BMC) and a host 
> processor.
> +
> +Required properties:
> + - compatible		: must be "aspeed,ast2500-xdma" or
> +			  "aspeed,ast2600-xdma"
> + - reg			: contains the address and size of the memory region
> +			  associated with the XDMA engine registers
> + - clocks		: clock specifier for the clock associated with the
> +			  XDMA engine
> + - resets		: reset specifier for the syscon reset associated with
> +			  the XDMA engine
> + - interrupts-extended	: two interrupt cells; the first specifies the 
> global
> +			  interrupt for the XDMA engine and the second
> +			  specifies the PCI-E reset or PERST interrupt.
> + - aspeed,scu		: a phandle to the syscon node for the system control
> +			  unit of the SOC
> + - memory		: contains the address and size of the memory area to
> +			  be used by the XDMA engine for DMA operations
> +
> +Optional properties:
> + - pcie-device		: should be either "bmc" or "vga", corresponding to
> +			  which device should be used by the XDMA engine for
> +			  DMA operations. If this property is not set, the XDMA
> +			  engine will use the BMC PCI-E device.
> +
> +Example:
> +
> +    xdma@1e6e7000 {
> +        compatible = "aspeed,ast2500-xdma";
> +        reg = <0x1e6e7000 0x100>;
> +        clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
> +        resets = <&syscon ASPEED_RESET_XDMA>;
> +        interrupts-extended = <&vic 6>, <&scu_ic 
> ASPEED_AST2500_SCU_IC_PCIE_RESET_LO_TO_HI>;
> +        scu = <&syscon>;

You missed fixing the example :)

Andrew