[PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab

From: Icenowy Zheng
Date: Fri Jan 10 2020 - 10:54:36 EST

Next message: Lorenzo Pieralisi: "Re: [PATCH v2] PCI: tegra: Fix afi_pex2_ctrl reg offset for Tegra30"
Previous message: Icenowy Zheng: "[PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet"
In reply to: Rob Herring: "Re: [PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet"
Next in thread: Maxime Ripard: "Re: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, and
the front camera currently lacks a driver and a facility to share the
bus with the rear one.

Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-a64-pinetab.dts | 461 ++++++++++++++++++
2 files changed, 462 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index cf4f78617c3f..6dad63881cd3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
new file mode 100644
index 000000000000..1dfa3668636e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Icenowy Zheng <icenowy@xxxxxxxx>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "PineTab";
+ compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &rtl8723cs;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+ power-supply = <&vdd_bl>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ i2c-csi {
+ compatible = "i2c-gpio";
+ sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
+ scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */
+ i2c-gpio,delay-us = <5>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Rear camera */
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&csi_mclk_pin>;
+ clocks = <&ccu CLK_CSI_MCLK>;
+ clock-names = "xclk";
+
+ AVDD-supply = <&reg_dldo3>;
+ DOVDD-supply = <&reg_aldo1>;
+ DVDD-supply = <&reg_eldo3>;
+ reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */
+ powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+
+ port {
+ ov5640_ep: endpoint {
+ remote-endpoint = <&csi_ep>;
+ bus-width = <8>;
+ hsync-active = <1>; /* Active high */
+ vsync-active = <0>; /* Active low */
+ data-active = <1>; /* Active high */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+ };
+ };
+
+ speaker_amp: audio-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
+ sound-name-prefix = "Speaker Amp";
+ };
+
+ vdd_bl: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "bl-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ enable-active-high;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&codec {
+ status = "okay";
+};
+
+&codec_analog {
+ hpvcc-supply = <&reg_eldo1>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc2>;
+};
+
+&csi {
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi_ep: endpoint {
+ remote-endpoint = <&ov5640_ep>;
+ bus-width = <8>;
+ hsync-active = <1>; /* Active high */
+ vsync-active = <0>; /* Active low */
+ data-active = <1>; /* Active high */
+ pclk-sample = <1>; /* Rising */
+ };
+ };
+};
+
+&dai {
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&dphy {
+ status = "okay";
+};
+
+&dsi {
+ vcc-dsi-supply = <&reg_dldo1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "feixin,k101-im2ba02";
+ reg = <0>;
+ avdd-supply = <&reg_dc1sw>;
+ dvdd-supply = <&reg_dc1sw>;
+ cvdd-supply = <&reg_ldo_io1>;
+ reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+ backlight = <&backlight>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+
+ touchscreen@5d {
+ compatible = "goodix,gt9271";
+ reg = <0x5d>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
+ irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ AVDD28-supply = <&reg_ldo_io1>;
+ };
+};
+
+&i2c0_pins {
+ bias-pull-up;
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+
+ bma223@18 {
+ compatible = "bosch,bma223", "bosch,bma222e";
+ reg = <0x18>;
+ interrupt-parent = <&pio>;
+ interrupts = <7 5 IRQ_TYPE_LEVEL_HIGH>; /* PH5 */
+ mount-matrix = "0", "-1", "0",
+ "-1", "0", "0",
+ "0", "0", "-1";
+ };
+};
+
+&lradc {
+ vref-supply = <&reg_aldo3>;
+ status = "okay";
+
+ button-200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button-400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mixer1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&reg_dldo4>;
+ vqmmc-supply = <&reg_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8723cs: wifi@1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ vqmmc-supply = <&reg_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pwm {
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp803.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
+&reg_aldo1 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "dovdd-csi";
+};
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+&reg_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&reg_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca-1v8";
+};
+
+&reg_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-1v8-csi";
+};
+
+&reg_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+&reg_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_ldo_io0 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb";
+ status = "okay";
+};
+
+&reg_ldo_io1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <3500000>;
+ regulator-name = "vcc-touchscreen";
+ status = "okay";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&sound {
+ status = "okay";
+ simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
+ simple-audio-card,widgets = "Microphone", "Internal Microphone Left",
+ "Microphone", "Internal Microphone Right",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Internal Speaker";
+ simple-audio-card,routing =
+ "Left DAC", "AIF1 Slot 0 Left",
+ "Right DAC", "AIF1 Slot 0 Right",
+ "Speaker Amp INL", "LINEOUT",
+ "Speaker Amp INR", "LINEOUT",
+ "Internal Speaker", "Speaker Amp OUTL",
+ "Internal Speaker", "Speaker Amp OUTR",
+ "Headphone Jack", "HP",
+ "AIF1 Slot 0 Left ADC", "Left ADC",
+ "AIF1 Slot 0 Right ADC", "Right ADC",
+ "Internal Microphone Left", "MBIAS",
+ "MIC1", "Internal Microphone Left",
+ "Internal Microphone Right", "HBIAS",
+ "MIC2", "Internal Microphone Right";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <&reg_drivevbus>;
+ usb1_vbus-supply = <&reg_ldo_io0>;
+ status = "okay";
+};
--
2.23.0

Next message: Lorenzo Pieralisi: "Re: [PATCH v2] PCI: tegra: Fix afi_pex2_ctrl reg offset for Tegra30"
Previous message: Icenowy Zheng: "[PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet"
In reply to: Rob Herring: "Re: [PATCH 4/5] dt-bindings: arm: sunxi: add binding for PineTab tablet"
Next in thread: Maxime Ripard: "Re: [PATCH 5/5] arm64: dts: allwinner: a64: add support for PineTab"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]