[PATCH 00/28] ata: optimize core code size on PATA only setups

[Bartlomiej Zolnierkiewicz]

Hi,

There have been reports in the past of libata core code size
being a problem in migration from deprecated IDE subsystem on
legacy PATA only systems, i.e.:

https://lore.kernel.org/linux-ide/db2838b7-4862-785b-3a1d-3bf09811340a@xxxxxxxxx/

This patchset re-organizes libata core code to exclude SATA
specific code from being built for PATA only setups.

The end result is up to 17% (by 17246 bytes, from 101787 bytes to
84541 bytes) smaller libata core code size (as measured for m68k
arch using atari_defconfig) on affected setups.

I've tested this patchset using pata_falcon driver under ARAnyM
emulator.


patches #1-9 are general fixes/cleanups done in the process of
making the patchset (there should be no inter-dependencies between
them except patch #9 which depends on patch #8)

patch #10 separates PATA timings code to libata-pata-timings.c file

patch #11 optimizes ata_ncq_enable() inline for PATA only setups

patches #12-22 separate SATA only code from libata-core.c file to
libata-core-sata.c one

patches #24-25 separate SATA only code from libata-scsi.c file to
libata-scsi-sata.c one

patches #26-28 separate SATA only code from libata-eh.c file to
libata-eh-sata.c one


Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics


Bartlomiej Zolnierkiewicz (28):
  ata: remove stale maintainership information from core code
  ata: expose ncq_enable_prio sysfs attribute only on NCQ capable hosts
  ata: make SATA_PMP option selectable only if any SATA host driver is
    enabled
  sata_promise: use ata_cable_sata()
  ata: simplify ata_scsiop_inq_89()
  ata: use COMMAND_LINE_SIZE for ata_force_param_buf[] size
  ata: optimize struct ata_force_param size
  ata: move EXPORT_SYMBOL_GPL()s close to exported code
  ata: remove EXPORT_SYMBOL_GPL()s not used by modules
  ata: separate PATA timings code from libata-core.c
  ata: add CONFIG_SATA_HOST=n version of ata_ncq_enabled()
  ata: start separating SATA specific code from libata-core.c
  ata: move ata_do_link_spd_horkage() to libata-core-sata.c
  ata: move ata_dev_config_ncq*() to libata-core-sata.c
  ata: move sata_print_link_status() to libata-core-sata.c
  ata: move sata_down_spd_limit() to libata-core-sata.c
  ata: move *sata_set_spd*() to libata-core-sata.c
  ata: move sata_link_{debounce,resume}() to libata-core-sata.c
  ata: move sata_link_hardreset() to libata-core-sata.c
  ata: move sata_link_init_spd() to libata-core-sata.c
  ata: move ata_qc_complete_multiple() to libata-core-sata.c
  ata: move sata_scr_*() to libata-core-sata.c
  ata: move sata_deb_timing_*() to libata-core-sata.c
  ata: start separating SATA specific code from libata-scsi.c
  ata: move ata_sas_*() to libata-scsi-sata.c
  ata: start separating SATA specific code from libata-eh.c
  ata: move ata_eh_analyze_ncq_error() & co. to libata-core-sata.c
  ata: move ata_eh_set_lpm() to libata-core-sata.c

 drivers/ata/Kconfig               |   61 ++
 drivers/ata/Makefile              |    3 +
 drivers/ata/libata-core-sata.c    | 1077 +++++++++++++++++++++
 drivers/ata/libata-core.c         | 1456 ++---------------------------
 drivers/ata/libata-eh-sata.c      |  349 +++++++
 drivers/ata/libata-eh.c           |  354 +------
 drivers/ata/libata-pata-timings.c |  180 ++++
 drivers/ata/libata-scsi-sata.c    |  523 +++++++++++
 drivers/ata/libata-scsi.c         |  542 +----------
 drivers/ata/libata-sff.c          |    4 -
 drivers/ata/libata.h              |   69 +-
 drivers/ata/sata_promise.c        |    8 +-
 drivers/scsi/Kconfig              |    1 +
 drivers/scsi/libsas/Kconfig       |    1 +
 include/linux/libata.h            |  176 ++--
 15 files changed, 2496 insertions(+), 2308 deletions(-)
 create mode 100644 drivers/ata/libata-core-sata.c
 create mode 100644 drivers/ata/libata-eh-sata.c
 create mode 100644 drivers/ata/libata-pata-timings.c
 create mode 100644 drivers/ata/libata-scsi-sata.c

-- 
2.24.1