Re: [PATCH v4 1/8] dt-bindings: phy: qcom,qusb2: Convert QUSB2 phy bindings to yaml

[Matthias Kaehlcke]

Hi Sandeep,

On Wed, Jan 29, 2020 at 07:21:52PM +0530, Sandeep Maheswaram wrote:
> Convert QUSB2 phy  bindings to DT schema format using json-schema.
> 
> Signed-off-by: Sandeep Maheswaram <sanm@xxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/phy/qcom,qusb2-phy.yaml    | 142 +++++++++++++++++++++
>  .../devicetree/bindings/phy/qcom-qusb2-phy.txt     |  68 ----------
>  2 files changed, 142 insertions(+), 68 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
>  delete mode 100644 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
> new file mode 100644
> index 0000000..90b3cc6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
> @@ -0,0 +1,142 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,qusb2-phy.yaml#";
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#";
> +
> +title: Qualcomm QUSB2 phy controller
> +
> +maintainers:
> +  - Manu Gautam <mgautam@xxxxxxxxxxxxxx>
> +
> +description:
> +  QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,msm8996-qusb2-phy
> +      - qcom,msm8998-qusb2-phy
> +      - qcom,sdm845-qusb2-phy

If you wanted to maintain the comments from the .txt file you could add
them after the compatible string (e.g.
Documentation/devicetree/bindings/pwm/pwm-samsung.yaml)

> +  reg:
> +    maxItems: 1
> +
> +  "#phy-cells":
> +    const: 0
> +
> +  clocks:
> +    minItems: 2

       maxItems: 3 ?

> +    items:
> +      - description: phy config clock
> +      - description: 19.2 MHz ref clk
> +      - description: phy interface clock (Optional)
> +
> +  clock-names:
> +    minItems: 2

       maxItems: 3 ?

> +    items:
> +      - const: cfg_ahb
> +      - const: ref
> +      - const: iface
> +
> +  vdda-pll-supply:
> +     description:
> +       Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> +  vdda-phy-dpdm-supply:
> +     description:
> +       Phandle to 3.1V regulator supply to Dp/Dm port signals.
> +
> +  resets:
> +    maxItems: 1

       description:
         Phandle to reset to phy block.

> +
> +  nvmem-cells:
> +    maxItems: 1
> +    description:
> +        Phandle to nvmem cell that contains 'HS Tx trim'
> +        tuning parameter value for qusb2 phy.
> +
> +  qcom,tcsr-syscon:
> +    description:
> +        Phandle to TCSR syscon register region.
> +    $ref: /schemas/types.yaml#/definitions/cell
> +
> +  qcom,imp-res-offset-value:
> +    description:
> +        It is a 6 bit value that specifies offset to be
> +        added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
> +        tuning parameter that may vary for different boards of same SOC.
> +        This property is applicable to only QUSB2 v2 PHY.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - minimum: 0
> +        maximum: 63
> +        default: 0
> +
> +  qcom,hstx-trim-value:
> +    description:
> +        It is a 4 bit value that specifies tuning for HSTX
> +        output current.
> +        Possible range is - 15mA to 24mA (stepsize of 600 uA).
> +        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
> +        This property is applicable to only QUSB2 v2 PHY.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - minimum: 0
> +        maximum: 15
> +        default: 3
> +
> +  qcom,preemphasis-level:
> +    description:
> +        It is a 2 bit value that specifies pre-emphasis level.
> +        Possible range is 0 to 15% (stepsize of 5%).
> +        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
> +        This property is applicable to only QUSB2 v2 PHY.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - minimum: 0
> +        maximum: 3
> +        default: 2
> +
> +  qcom,preemphasis-width:
> +    description:
> +        It is a 1 bit value that specifies how long the HSTX
> +        pre-emphasis (specified using qcom,preemphasis-level) must be in
> +        effect. Duration could be half-bit of full-bit.
> +        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
> +        This property is applicable to only QUSB2 v2 PHY.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - minimum: 0
> +        maximum: 1
> +        default: 0

I think you could put the properties that are only applicable for QUSB2
v2 PHY into a block like this and remove the 'This property is
applicable to only QUSB2 v2 PHY.' comment from the property description:

if:
  properties:
    compatible:
      contains:
        const: qcom,sdm845-qusb2-phy
then:
  qcom,imp-res-offset-value:
    ...


Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>