Re: [PATCHv5 06/14] remoteproc/omap: Initialize and assign reserved memory node

[Suman Anna]

On 1/30/20 3:57 PM, Suman Anna wrote:
> On 1/30/20 3:50 PM, Andrew F. Davis wrote:
>> On 1/30/20 4:39 PM, Suman Anna wrote:
>>> On 1/30/20 3:19 PM, Andrew F. Davis wrote:
>>>> On 1/30/20 3:39 PM, Suman Anna wrote:
>>>>> On 1/30/20 2:22 PM, Andrew F. Davis wrote:
>>>>>> On 1/30/20 2:55 PM, Suman Anna wrote:
>>>>>>> On 1/30/20 1:42 PM, Tero Kristo wrote:
>>>>>>>> On 30/01/2020 21:20, Andrew F. Davis wrote:
>>>>>>>>> On 1/30/20 2:18 PM, Tero Kristo wrote:
>>>>>>>>>> On 30/01/2020 20:11, Andrew F. Davis wrote:
>>>>>>>>>>> On 1/16/20 8:53 AM, Tero Kristo wrote:
>>>>>>>>>>>> From: Suman Anna <s-anna@xxxxxx>
>>>>>>>>>>>>
>>>>>>>>>>>> The reserved memory nodes are not assigned to platform devices by
>>>>>>>>>>>> default in the driver core to avoid the lookup for every platform
>>>>>>>>>>>> device and incur a penalty as the real users are expected to be
>>>>>>>>>>>> only a few devices.
>>>>>>>>>>>>
>>>>>>>>>>>> OMAP remoteproc devices fall into the above category and the OMAP
>>>>>>>>>>>> remoteproc driver _requires_ specific CMA pools to be assigned
>>>>>>>>>>>> for each device at the moment to align on the location of the
>>>>>>>>>>>> vrings and vring buffers in the RTOS-side firmware images. So,
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> Same comment as before, this is a firmware issue for only some
>>>>>>>>>>> firmwares
>>>>>>>>>>> that do not handle being assigned vring locations correctly and instead
>>>>>>>>>>> hard-code them.
>>>>>>>
>>>>>>> As for this statement, this can do with some updating. Post 4.20,
>>>>>>> because of the lazy allocation scheme used for carveouts including the
>>>>>>> vrings, the resource tables now have to use FW_RSC_ADDR_ANY and will
>>>>>>> have to wait for the vdev synchronization to happen.
>>>>>>>
>>>>>>>>>>
>>>>>>>>>> I believe we discussed this topic in length in previous version but
>>>>>>>>>> there was no conclusion on it.
>>>>>>>>>>
>>>>>>>>>> The commit desc might be a bit misleading, we are not actually forced to
>>>>>>>>>> use specific CMA buffers, as we use IOMMU to map these to device
>>>>>>>>>> addresses. For example IPU1/IPU2 use internally exact same memory
>>>>>>>>>> addresses, iommu is used to map these to specific CMA buffer.
>>>>>>>>>>
>>>>>>>>>> CMA buffers are mostly used so that we get aligned large chunk of memory
>>>>>>>>>> which can be mapped properly with the limited IOMMU OMAP family of chips
>>>>>>>>>> have. Not sure if there is any sane way to get this done in any other
>>>>>>>>>> manner.
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Why not use the default CMA area?
>>>>>>>>
>>>>>>>> I think using default CMA area getting the actual memory block is not
>>>>>>>> guaranteed and might fail. There are other users for the memory, and it
>>>>>>>> might get fragmented at the very late phase we are grabbing the memory
>>>>>>>> (omap remoteproc driver probe time.) Some chunks we need are pretty large.
>>>>>>>>
>>>>>>>> I believe I could experiment with this a bit though and see, or Suman
>>>>>>>> could maybe provide feedback why this was designed initially like this
>>>>>>>> and why this would not be a good idea.
>>>>>>>
>>>>>>> I have given some explanation on this on v4 as well, but if it is not
>>>>>>> clear, there are restrictions with using default CMA. Default CMA has
>>>>>>> switched to be assigned from the top of the memory (higher addresses,
>>>>>>> since 3.18 IIRC), and the MMUs on IPUs and DSPs can only address
>>>>>>> 32-bits. So, we cannot blindly use the default CMA pool, and this will
>>>>>>> definitely not work on boards > 2 GB RAM. And, if you want to add in any
>>>>>>> firewall capability, then specific physical addresses becomes mandatory.
>>>>>>>
>>>>>>
>>>>>>
>>>>>> If you need 32bit range allocations then
>>>>>> dma_set_mask(dev, DMA_BIT_MASK(32));
>>>>>>
>>>>>> I'm not saying don't have support for carveouts, just make them
>>>>>> optional, keystone_remoteproc.c does this:
>>>>>>
>>>>>> if (of_reserved_mem_device_init(dev))
>>>>>> 	dev_warn(dev, "device does not have specific CMA pool\n");
>>>>>>
>>>>>> There doesn't even needs to be a warning but that is up to you.
>>>>>
>>>>> It is not exactly an apples to apples comparison. K2s do not have MMUs,
>>>>> and most of our firmware images on K2 are actually running out of the
>>>>> DSP internal memory.
>>>>>
>>>>
>>>>
>>>> So again we circle back to it being a firmware issue, if K2 can get away
>>>> without needing carveouts and it doesn't even have an MMU then certainly
>>>> OMAP/DRA7x class devices can handle it even better given they *do* have
>>>> an IOMMU. Unless someone is hard-coding the IOMMU configuration.. In
>>>> which case we are still just hacking around the problem here with
>>>> mandatory specific address memory carveouts.
>>>
>>> Optional carveouts on OMAP remoteprocs can be an enhancement in the
>>> future, but at the moment, we won't be able to run use-cases without
>>> this. And I have already given some of the reasons for the same here and
>>> on v4.
>>>
>>
>>
>> No reason to be dismissive, my questions are valid.
>>
>> What "use-cases" are we talking about, I have firmware that doesn't need
>> specific carved-out addresses. 
> 
> I think you are well aware of all the usecases we provide with the TI
> SDKs with IPUs and DSPs. And what is the firmware that you have and what
> do you use it for?
> 
> If you have misbehaving firmware that
>> needs statically carved out memory addresses then you can have carveouts
>> if you want, but it should be optional. 
> If I don't want to pollute my
>> system's memory space with a bunch of carveout holes then I shouldn't
>> have to just because your specific firmware needs them.
> 
> Further follow-up series like early-boot and late-attach will mandate
> fixed carveouts actually. You cannot just run out of any random memory.

Also, these are CMA pools ("reusable"), so they are not actual carveout
holes ("no-map"). This is the preferred method in remoteproc mode so
that the memory is available for kernel when remoteprocs are not in use.
Customers can always choose to make these carveouts so that they do not
run into memory allocation issues when changing firmwares and under
stress conditions. These will have to be carveouts for early-boot usecases.

regards
Suman

> 
> regards
> Suman
> 
>>
>> Andrew
>>
>>
>>> regards
>>> Suman
>>>
>>>>
>>>> Andrew
>>>>
>>>>
>>>>> regards
>>>>> Suman
>>>>>
>>>>>>
>>>>>> Andrew
>>>>>>
>>>>>>
>>>>>>> regards
>>>>>>> Suman
>>>>>>>
>>>>>>>>
>>>>>>>> -Tero
>>>>>>>>
>>>>>>>>>
>>>>>>>>> Andrew
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> -Tero
>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>> This is not a requirement of the remote processor itself and so it
>>>>>>>>>>> should not fail to probe if a specific memory carveout isn't given.
>>>>>>>>>>>
>>>>>>>>>>>
>>>>>>>>>>>> use the of_reserved_mem_device_init/release() API appropriately
>>>>>>>>>>>> to assign the corresponding reserved memory region to the OMAP
>>>>>>>>>>>> remoteproc device. Note that only one region per device is
>>>>>>>>>>>> allowed by the framework.
>>>>>>>>>>>>
>>>>>>>>>>>> Signed-off-by: Suman Anna <s-anna@xxxxxx>
>>>>>>>>>>>> Signed-off-by: Tero Kristo <t-kristo@xxxxxx>
>>>>>>>>>>>> Reviewed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>>>>>>>>>>>> ---
>>>>>>>>>>>> v5: no changes
>>>>>>>>>>>>
>>>>>>>>>>>> ÂÂ drivers/remoteproc/omap_remoteproc.c | 12 +++++++++++-
>>>>>>>>>>>> ÂÂ 1 file changed, 11 insertions(+), 1 deletion(-)
>>>>>>>>>>>>
>>>>>>>>>>>> diff --git a/drivers/remoteproc/omap_remoteproc.c
>>>>>>>>>>>> b/drivers/remoteproc/omap_remoteproc.c
>>>>>>>>>>>> index 0846839b2c97..194303b860b2 100644
>>>>>>>>>>>> --- a/drivers/remoteproc/omap_remoteproc.c
>>>>>>>>>>>> +++ b/drivers/remoteproc/omap_remoteproc.c
>>>>>>>>>>>> @@ -17,6 +17,7 @@
>>>>>>>>>>>> ÂÂ #include <linux/module.h>
>>>>>>>>>>>> ÂÂ #include <linux/err.h>
>>>>>>>>>>>> ÂÂ #include <linux/of_device.h>
>>>>>>>>>>>> +#include <linux/of_reserved_mem.h>
>>>>>>>>>>>> ÂÂ #include <linux/platform_device.h>
>>>>>>>>>>>> ÂÂ #include <linux/dma-mapping.h>
>>>>>>>>>>>> ÂÂ #include <linux/remoteproc.h>
>>>>>>>>>>>> @@ -480,14 +481,22 @@ static int omap_rproc_probe(struct
>>>>>>>>>>>> platform_device *pdev)
>>>>>>>>>>>> ÂÂÂÂÂÂ if (ret)
>>>>>>>>>>>> ÂÂÂÂÂÂÂÂÂÂ goto free_rproc;
>>>>>>>>>>>> ÂÂ +ÂÂÂ ret = of_reserved_mem_device_init(&pdev->dev);
>>>>>>>>>>>> +ÂÂÂ if (ret) {
>>>>>>>>>>>> +ÂÂÂÂÂÂÂ dev_err(&pdev->dev, "device does not have specific CMA
>>>>>>>>>>>> pool\n");
>>>>>>>>>>>> +ÂÂÂÂÂÂÂ goto free_rproc;
>>>>>>>>>>>> +ÂÂÂ }
>>>>>>>>>>>> +
>>>>>>>>>>>> ÂÂÂÂÂÂ platform_set_drvdata(pdev, rproc);
>>>>>>>>>>>> ÂÂ ÂÂÂÂÂ ret = rproc_add(rproc);
>>>>>>>>>>>> ÂÂÂÂÂÂ if (ret)
>>>>>>>>>>>> -ÂÂÂÂÂÂÂ goto free_rproc;
>>>>>>>>>>>> +ÂÂÂÂÂÂÂ goto release_mem;
>>>>>>>>>>>> ÂÂ ÂÂÂÂÂ return 0;
>>>>>>>>>>>> ÂÂ +release_mem:
>>>>>>>>>>>> +ÂÂÂ of_reserved_mem_device_release(&pdev->dev);
>>>>>>>>>>>> ÂÂ free_rproc:
>>>>>>>>>>>> ÂÂÂÂÂÂ rproc_free(rproc);
>>>>>>>>>>>> ÂÂÂÂÂÂ return ret;
>>>>>>>>>>>> @@ -499,6 +508,7 @@ static int omap_rproc_remove(struct
>>>>>>>>>>>> platform_device *pdev)
>>>>>>>>>>>> ÂÂ ÂÂÂÂÂ rproc_del(rproc);
>>>>>>>>>>>> ÂÂÂÂÂÂ rproc_free(rproc);
>>>>>>>>>>>> +ÂÂÂ of_reserved_mem_device_release(&pdev->dev);
>>>>>>>>>>>> ÂÂ ÂÂÂÂÂ return 0;
>>>>>>>>>>>> ÂÂ }
>>>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> --Â
>>>>>>>>
>>>>>>>> -- 
>>>>>>>> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
>>>>>>>> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
>>>>>>>
>>>>>
>>>
>