Re: [PATCH 1/2] dt-binding: Add DSI/LVDS tc358775 bridge bindings

[Laurent Pinchart]

Hello Vinay,

Please take into account the review comments from v1. We can discuss
them in replies to v1 if you have any question. I'll skip reviewing this
version.

On Wed, Mar 11, 2020 at 03:18:24PM +0530, Vinay Simha BN wrote:
> Add yaml documentation for DSI/LVDS tc358775 bridge
> 
> Signed-off-by: Vinay Simha BN <simhavcs@xxxxxxxxx>
> 
> ---
> v1:
>  Initial version
> ---
>  .../bindings/display/bridge/toshiba-tc358775.yaml  | 174 +++++++++++++++++++++
>  1 file changed, 174 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml
> new file mode 100644
> index 0000000..e9a9544
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml
> @@ -0,0 +1,174 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +
> +title: Toshiba TC358775 DSI to LVDS bridge bindings
> +
> +maintainers:
> +	- Vinay Simha BN <simhavcs@xxxxxxxxx>
> +
> +description: |
> +	This binding supports DSI to LVDS bridge TC358775
> +
> +properties:
> + compatible:
> +	const: toshiba,tc358775
> +
> + reg:
> +   maxItems: 1
> +   description: i2c address of the bridge, 0x0f
> +
> + tc, dsi-lanes: 1
> +   maxItems: 1
> +   description: Number of DSI data lanes connected to the DSI host. It should
> +  be one of 1, 2, 3 or 4.
> +
> + tc, dual-link: 1
> +   maxItems: 1
> +   description: To configure the LVDS transmitter either as single-link or dual-link.
> +
> + vdd-supply:
> +   maxItems: 1
> +   description:  1.2V LVDS Power Supply
> +
> + vddio-supply:
> +   maxItems: 1
> +   description: 1.8V IO Power Supply
> +
> + stby-gpios:
> +   maxItems: 1
> +   description: Standby pin, Low active
> +
> + reset-gpios:
> +   maxItems: 1
> +   description: Hardware reset, Low active
> +
> + ports:
> +   type: object
> +
> +    properties:
> +      port@0:
> +        type: object
> +        description: |
> +          DSI Input. The remote endpoint phandle should be a
> +	  reference to a valid mipi_dsi_host device node.
> +      port@1:
> +        type: object
> +        description: |
> +          Video port for LVDS output (panel or connector).
> +
> +      required:
> +      - port@0
> +      - port@1
> +
> +required:
> + - compatible
> + - reg
> + - dsi-lanes
> + - vdd-supply
> + - vddio-supply
> + - stby-gpios
> + - reset-gpios
> + - ports
> +
> +examples:
> + - |
> +   i2c@78b8000 {
> +	/* On High speed expansion */
> +	label = "HS-I2C2";
> +	status = "okay";
> +
> +	tc_bridge: bridge@f {
> +		status = "okay";
> +
> +		compatible = "toshiba,tc358775";
> +		reg = <0x0f>;
> +
> +		tc,dsi-lanes = <4>;
> +		tc,dual-link = <0>;
> +
> +		vdd-supply = <&pm8916_l2>;
> +		vddio-supply = <&pm8916_l6>;
> +
> +		stby-gpio = <&msmgpio 99 GPIO_ACTIVE_LOW>;
> +		reset-gpio = <&msmgpio 72 GPIO_ACTIVE_LOW>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				d2l_in: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				d2l_out: endpoint {
> +					remote-endpoint = <&panel_in>;
> +				};
> +			};
> +		};
> +	};
> +  };
> +
> +  panel: auo,b101xtn01 {
> +		status = "okay";
> +		compatible = "auo,b101xtn01", "panel-lvds";
> +		power-supply = <&pm8916_l14>;
> +
> +		width-mm = <223>;
> +		height-mm = <125>;
> +
> +		data-mapping = "jeida-24";
> +
> +		panel-timing {
> +			/* 1366x768 @60Hz */
> +			clock-frequency = <72000000>;
> +			hactive = <1366>;
> +			vactive = <768>;
> +			hsync-len = <70>;
> +			hfront-porch = <20>;
> +			hback-porch = <0>;
> +			vsync-len = <42>;
> +			vfront-porch = <14>;
> +			vback-porch = <0>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&d2l_out>;
> +			};
> +		};
> + };
> +
> +  mdss@1a00000 {
> +	status = "okay";
> +
> +	mdp@1a01000 {
> +		status = "okay";
> +	};
> +
> +	dsi@1a98000 {
> +		status = "okay";
> +		..
> +		ports {
> +			port@1 {
> +				dsi0_out: endpoint {
> +					remote-endpoint = <&d2l_in>;
> +					data-lanes = <0 1 2 3>;
> +				};
> +			};
> +		};
> +	};
> +
> +	dsi-phy@1a98300 {
> +		status = "okay";
> +		..
> +	};
> + };

-- 
Regards,

Laurent Pinchart