Quoting Akash Asthana (2020-02-17 01:49:33)ok
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yamlDrop the | because it doesn't look like any formatting needs to be
new file mode 100644
index 0000000..977070a
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id:"http://devicetree.org/schemas/spi/qcom,spi-qcom-qspi.yaml#"
+$schema:"http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Quad Serial Peripheral Interface (QSPI)
+
+maintainers:
+ - Mukesh Savaliya<msavaliy@xxxxxxxxxxxxxx>
+ - Akash Asthana<akashast@xxxxxxxxxxxxxx>
+
+description: |
maintained in the text for the description.
ok+ The QSPI controller allows SPI protocol communication in single, dual, or quadDrop description? It doesn't seem useful.
+ wire transmission modes for read/write access to slaves such as NOR flash.
+
+allOf:
+ - $ref: /spi/spi-controller.yaml#
+
+properties:
+ compatible:
+ items:
+ - const: qcom,sdm845-qspi
+ - const: qcom,qspi-v1
+
+ reg:
+ description: Base register location and length.
ok+ maxItems: 1Please drop the full-stop on core clock.
+
+ interrupts:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: iface
+ - const: core
+
+ clocks:
+ items:
+ - description: AHB clock
+ - description: QSPI core clock.
ok+Aren't these two unnecessary because they're covered by the
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
spi-controller.yaml binding?
ok will remove
+These last two are also covered by spi-controller binding.
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clock-names
+ - clocks
+ - "#address-cells"
+ - "#size-cells"
+Why two newlines instead of one?
+
+examples:Remove this node from example please.
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc: soc@0 {
Ok, I will align it better.
+ #address-cells = <2>;Weird tabbing here. Just use spaces and align it up.
+ #size-cells = <2>;
+
+ qspi: spi@88df000 {
+ compatible = "qcom,sdm845-qspi", "qcom,qspi-v1";
+ reg = <0 0x88df000 0 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clock-names = "iface", "core";
+ clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+ <&gcc GCC_QSPI_CORE_CLK>;
+Is this flash node necessary for the example?
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
+ };Nitpick: Why newline here?
+ };
+
+...