[PATCH] pinctrl: qcom: use scm_call to route GPIO irq to Apps

[Ansuel Smith]

For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.

Signed-off-by: Ajay Kishore <akisho@xxxxxxxxxxxxxx>
Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
---
 drivers/pinctrl/qcom/pinctrl-msm.c | 36 ++++++++++++++++++++++++++----
 1 file changed, 32 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 9a8daa256a32..a83cfd1da219 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -22,6 +22,8 @@
 #include <linux/reboot.h>
 #include <linux/pm.h>
 #include <linux/log2.h>
+#include <linux/qcom_scm.h>
+#include <linux/io.h>
 
 #include <linux/soc/qcom/irq.h>
 
@@ -710,6 +712,9 @@ static void msm_gpio_irq_mask(struct irq_data *d)
 	const struct msm_pingroup *g;
 	unsigned long flags;
 	u32 val;
+	u32 addr;
+	int ret;
+	const __be32 *reg;
 
 	if (d->parent_data)
 		irq_chip_mask_parent(d);
@@ -863,6 +868,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	const struct msm_pingroup *g;
 	unsigned long flags;
 	u32 val;
+	int ret;
 
 	if (d->parent_data)
 		irq_chip_set_type_parent(d, type);
@@ -882,11 +888,33 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	else
 		clear_bit(d->hwirq, pctrl->dual_edge_irqs);
 
+	ret = of_device_is_compatible(pctrl->dev->of_node,
+					"qcom,ipq8064-pinctrl");
 	/* Route interrupts to application cpu */
-	val = msm_readl_intr_target(pctrl, g);
-	val &= ~(7 << g->intr_target_bit);
-	val |= g->intr_target_kpss_val << g->intr_target_bit;
-	msm_writel_intr_target(val, pctrl, g);
+	if (!ret) {
+		val = msm_readl_intr_target(pctrl, g);
+		val &= ~(7 << g->intr_target_bit);
+		val |= g->intr_target_kpss_val << g->intr_target_bit;
+		msm_writel_intr_target(val, pctrl, g);
+	} else {
+		const __be32 *reg = of_get_property(pctrl->dev->of_node,
+						    "reg", NULL);
+
+		if (reg) {
+			u32 addr = be32_to_cpup(reg) + g->intr_target_reg;
+
+			qcom_scm_io_readl(addr, &val);
+			__iormb();
+
+			val &= ~(7 << g->intr_target_bit);
+			val |= g->intr_target_kpss_val << g->intr_target_bit;
+
+			__iowmb();
+			ret = qcom_scm_io_writel(addr, val);
+			if (ret)
+				pr_err("\n Routing interrupts to Apps proc failed");
+		}
+	}
 
 	/* Update configuration for gpio.
 	 * RAW_STATUS_EN is left on for all gpio irqs. Due to the
-- 
2.25.0