[PATCH] serial: 8250_omap: Fix sleeping function called from invalid context during probe

[Peter Ujfalusi]

When booting j721e the following bug is printed:

[    1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[    1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[    1.154832] 3 locks held by kworker/0:1/12:
[    1.154836]  #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154852]  #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154860]  #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[    1.154872] irq event stamp: 63096
[    1.154881] hardirqs last  enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[    1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[    1.154893] softirqs last  enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[    1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[    1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[    1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[    1.154917] Workqueue: events deferred_probe_work_func
[    1.154923] Call trace:
[    1.154928]  dump_backtrace+0x0/0x190
[    1.154933]  show_stack+0x14/0x20
[    1.154940]  dump_stack+0xe0/0x148
[    1.154946]  ___might_sleep+0x150/0x1f0
[    1.154952]  __might_sleep+0x4c/0x80
[    1.154957]  wait_for_completion_timeout+0x40/0x140
[    1.154964]  ti_sci_set_device_state+0xa0/0x158
[    1.154969]  ti_sci_cmd_get_device_exclusive+0x14/0x20
[    1.154977]  ti_sci_dev_start+0x34/0x50
[    1.154984]  genpd_runtime_resume+0x78/0x1f8
[    1.154991]  __rpm_callback+0x3c/0x140
[    1.154996]  rpm_callback+0x20/0x80
[    1.155001]  rpm_resume+0x568/0x758
[    1.155007]  __pm_runtime_resume+0x44/0xb0
[    1.155013]  omap8250_probe+0x2b4/0x508
[    1.155019]  platform_drv_probe+0x50/0xa0
[    1.155023]  really_probe+0xd4/0x318
[    1.155028]  driver_probe_device+0x54/0xe8
[    1.155033]  __device_attach_driver+0x80/0xb8
[    1.155039]  bus_for_each_drv+0x74/0xc0
[    1.155044]  __device_attach+0xdc/0x138
[    1.155049]  device_initial_probe+0x10/0x18
[    1.155053]  bus_probe_device+0x98/0xa0
[    1.155058]  deferred_probe_work_func+0x74/0xb0
[    1.155063]  process_one_work+0x280/0x6e8
[    1.155068]  worker_thread+0x48/0x430
[    1.155073]  kthread+0x108/0x138
[    1.155079]  ret_from_fork+0x10/0x18

To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.

Reported-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@xxxxxx>
---
 drivers/tty/serial/8250/8250_omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index a2e5a4e77000..611e3002d68c 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -1202,6 +1202,7 @@ static int omap8250_probe(struct platform_device *pdev)
 	spin_lock_init(&priv->rx_dma_lock);
 
 	device_init_wakeup(&pdev->dev, true);
+	pm_runtime_enable(&pdev->dev);
 	pm_runtime_use_autosuspend(&pdev->dev);
 
 	/*
@@ -1215,7 +1216,6 @@ static int omap8250_probe(struct platform_device *pdev)
 		pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
 
 	pm_runtime_irq_safe(&pdev->dev);
-	pm_runtime_enable(&pdev->dev);
 
 	pm_runtime_get_sync(&pdev->dev);
 
-- 
Peter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki